ページ1に含まれる内容の要旨
HomePlug to Ethernet Bridge
User Manual (GHPB01)
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Welcome Thank you for purchasing one of the most user-friendly networking devices on the market. IOGEAR’s HomePlug to Ethernet Bridges are first-class networking devices designed to network your computers at home (or in your small office). This device allows you to set up your home network via the most pervasive medium in your house – the home power lines. It is easy to set up, and it doesn’t require any additional wiring in the house. To better serve you, IOGEAR offers an array of additional US
ページ4に含まれる内容の要旨
Table of Contents Overview 02 Technical Support 67 Features 03 Product Specifications 69 Requirements 04 Limited Warranty 70 Introduction 05 Installation 07 Network Configuration 14 Networking Basics 27 - Network Setup Wizard 27 - Checking IP Address 38 - Assign a Static IP address 40 - Sharing Disks/Folders 43 - Sharing Printers 48 - Accessing the Internet 59 Troubleshooting 63
ページ5に含まれる内容の要旨
Overview IOGEAR's HomePlug Powerline Network Ethernet Bridge allows you to network your home comput- ers through the electric power lines in the house. Setting up a home network has never been so simple, just connect your computer to the HomePlug Bridge via the CAT5 patch cable provided in the package, and then plug the power end to your AC power outlet, you are connected! This unit is compliant to HomePlug Powerline Specification 1.0 and offers up to 14 Mbps bandwidth while being less prone to
ページ6に含まれる内容の要旨
Features • No extra wires, using the most pervasive medium in your home - power lines • Allows multiple computers to share Internet access, printers, and other resources through the power lines • Very easy and intuitive to set up and install • HomePlug Powerline Specification 1.0 compliant • Up to 14 Mbps bandwidth • Up to 990' distance through the power lines, far enough for most households • Worldwide compatibility • Low risk of interference by other RF sources • 56-bit DES encryption assures
ページ7に含まれる内容の要旨
Requirements System Requirements • Available AC power outlets in the room. • Standard home power line wiring. • Computers with 10/100Base-T adapters, or 10/100Base-T switch/hub. • When used as a node: Windows 98SE, ME, 2000, XP. • When used as a bridge: any operating system (OS transparent). 4
ページ8に含まれる内容の要旨
Introduction IOGEAR's HomePlug to Ethernet Bridge allows you to network your computers via your existing home power lines. It offers a data transmission speed of up to 14 Mbps, and reaches up to 990 feet through standard power lines. Package contents: 1. HomePlug to Ethernet Bridge 2. CAT5 patch cable 3. Power cable 4. User Manual 5. Warranty Registration Card 1. 2. 3. 5
ページ9に含まれる内容の要旨
Introduction Front View: (Drawing) 1. Power LED - lights up in green when plugged into a power outlet 2. Collision LED - lights up in green whenever there is collision 3. Link LED - lights up in green after plugged into a power outlet 4. ACT LED - blinks in green when there is network activity 5. Ethernet port - connecting to the computer 6. Normal/Uplink button - you only need to use this button when connecting the bridge to a switch/hub. Push this button when connects to the Uplink port on a
ページ10に含まれる内容の要旨
Installation There are several ways to network your computers using the HomePlug Bridge. Before we get started, please NOTE: Do not place HomePlug devices under direct sunlight or near high heat emitting devices; Do not place HomePlug devices near water or wet surfaces to avoid electric hazards; Do not place HomePlug devices on any moving or unstable surfaces; It is recommended that you plug the HomePlug devices directly into the wall outlets, not to any power adapters, surge protectors or any d
ページ11に含まれる内容の要旨
Installation If you plan to use this unit as a NODE, not as a BRIDGE (refer to the Network Terms for details): 1. Remove the HomePlug Bridge, the power cord, the CAT5 cable and the installation CD from the package. 2. Allocate a space for the adapter's placement. Make sure you avoid the places mentioned on the previous page. 3. Make sure that your HomePlug bridge is NOT CONNECTED TO THE COMPUTER before you install the driver. 4. Insert the installation CD. If CD does not automatically load, run
ページ12に含まれる内容の要旨
Installation 6. Read, understand and accept the License Agreement and Con- tinue by clicking Next. 9
ページ13に含まれる内容の要旨
Installation 7. Enter a username and organiza- tion name, and continue installa- tion. (Username and Organiza- tion have no importance in device operation. This window might look slightly different on other plat- forms.) 10
ページ14に含まれる内容の要旨
Installation 8. Click Install to start the Installa- tion Wizard: 11
ページ15に含まれる内容の要旨
Installation 9. After installation is successful, a win- dow will pop up prompting for the in- stallation of the HomePlug Bridge. Plug in the CAT5 cable, one end into the Ethernet port on the HomePlug Bridge, the other end into an available network port on your computer. Please verify that the green Power LED and Link LED on the HomePlug Bridge light up. 12
ページ16に含まれる内容の要旨
Installation 10. You have reached the end of your installation. Please restart your computer for changes to go into effect. 13
ページ17に含まれる内容の要旨
Network Configuration HomePlug Node Configuration Steps: 1. After restarting your computer, you should see this icon on your desktop. Click on it to begin configuring your HomePlug device. 14
ページ18に含まれる内容の要旨
Network Configuration 2. Click Next to begin the configuration. 15
ページ19に含まれる内容の要旨
Network Configuration 3. Click Next to continue. 16
ページ20に含まれる内容の要旨
Network Configuration 4. Type in a network password between 4 and 24 characters long and click Next. The password can consist of numbers and/or letters. 17
