ページ1に含まれる内容の要旨
™
™
Ethernet Pocket Hub
Model 0401
(E-TBT-HB-0401)
7345.C
For assistance in installing, using, or
maintaining the TRANSITION Networks
Model 0401 Ethernet Pocket Hub,
contact TRANSITION Networks
Technical Support at:
(800) 260-1312
or contact your local distributor.
ページ2に含まれる内容の要旨
The sole purpose of this remedy shall be provided the customer with the replacement or repair of non-conforming goods in the manner described in this Warranty statement. This exclusive remedy shall not be deemed to have failed of its essential purpose so long as TN is willing and able to repair or replace the defective item(s) or refund the purchase price. TN reserves the right to inspect products claimed to be defective under warranty either at the customer’s location or at TN’s plant. TN assu
ページ3に含まれる内容の要旨
Warranty Statement A. Five Year Warranty Transition Networks, Inc. (TN) warrants, for a period of five years, that TN products (with the exception of power supplies and fans that TN warrants for two years) will be free from defects in materials and workmanship, and will be in conformity with TN’s specifications. TN’s warranty on products manufactured by or assembled for TN in accordance with a Table of Contents customer’s specifications, is a five-year warranty that the goods conform to such spe
ページ4に含まれる内容の要旨
Ω Model 0401 Ethernet Pocket Hub 1. INTRODUCTION Specifications This guide is intended for the system or network administrator responsible for installing and monitoring a TRANSITION Networks Dimensions 0401 Ethernet Pocket Hub. A working knowledge of local area 4.80" X 2.77" X 0.95" (122mm x 70mm x 24mm) network (LAN) operations, including familiarity with communications protocols used on interconnected LANs, is Environment assumed. Temperature: 0-50°C, Humidity 10-90%, non condensing, The 040
ページ5に含まれる内容の要旨
5. MAINTENANCE 0401 Ethernet Pocket Hub Connectors and Status LEDs WARNING: DO NOT, UNDER ANY CIRCUMSTANCES, open and attempt to repair the 0401 Pocket Hub. Failure to RJ-45 Connectors observe this warning could result in personal injury or Four (4) 10BaseT RJ-45 jack death from electrical shock. connectors are located at one end of the 0401 Pocket Hub. NOTE: Failure to observe the above warning will immediately void The RJ-45 jacks support the warranty. connection to shielded or unshielded 10
ページ6に含まれる内容の要旨
2. SITE CONSIDERATIONS 4. OPERATION The site for the 0401 Ethernet Repeater Hub must provide: The 0401 Pocket Hub normally requires no intervention beyond • AC power outlet for each Hub occasionally monitoring the Power and Link/Transmit LEDs. • Adequate ventilation • Standard environmental conditions • Isolation from electrical noise, including radio transmitters and broadband amplifiers, motors, high power electrical lines, or fluorescent light fixtures. Additionally: • The twisted pair cabl
ページ7に含まれる内容の要旨
Connecting Pocket Hub to Powered PC Ensuring Correct 10BaseT Configuration The 10BaseT cable and RJ-45 jacks for Hub to Terminal connections NOTE: The 0401 Pocket Hub is powered ON when connected, must be configured as straight through. The 10BaseT cable and RJ-45 through the AUI connector, to a powered PC. After the AUI is jacks for Hub to Hub connections must be configured as crossover. connected to a PC, the green Power LED is illuminated. To power the 0401 pocket hub: The two active pairs i
ページ8に含まれる内容の要旨
Connecting Pocket Hub to 10BaseT Cable 3. INSTALLATION To connect 10BaseT Cable to Pocket Hub RJ-45 connectors: The 0401 Ethernet Pocket Hub is designed to draw power from the AUI port of a PC or hub. The 0401 Pocket Hub 1. Locate or build 10BaseT cables with the following MUST be connected to an AUI port BEFORE the 10BaseT characteristics: ports are allowed to be powered and active. • 802.3 compliant (See page 10) NOTE: 0401 Ethernet Pocket Hub Link Integrity cannot be • correct (straight thro
