ページ1に含まれる内容の要旨
unitech
PA600 Rugged Enterprise PDA
User’s Manual
400546G Rev. A
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Preface About This Manual This manual explains how to install, operate and maintain the PA600 PDA Barcode Scanner. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from the manufacturer. This includes electronic or mechanical means, such as photocopying, recording, or infor- mation storage and retrieval systems. The material in this manual is subject to change without notice. © Copyright 2006 Unitech
ページ4に含まれる内容の要旨
Laser Information The Unitech PA600 series is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1. Class II and Class 2 products are not considered to be hazardous. The PA600 series contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations. The scanner is designed so that there is no human access to harmful laser light during normal operation, us
ページ5に含まれる内容の要旨
About This Manual Storage and safety notice Although charged Lithium-Ion batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens, they will require recharging prior to use. Lithium-Ion batteries may be stored at tempera- tures between-20°C to 60°C, however they may be depleted more rapidly at the high end of this range. It is recommended to store batteries within normal room tempera- ture ranges. iii
ページ6に含まれる内容の要旨
iv
ページ7に含まれる内容の要旨
Table of Contents Preface About This Manual i Regulatory Compliance Statements ............................................................................. i FCC Statement........................................................................................................................ i Canadian Compliance Statement............................................................................................ i European Conformity Statement ...................................................
ページ8に含まれる内容の要旨
Chapter 3 Getting Connected 20 Establishing Device-PC Connection.......................................................................... 20 Installing Microsoft ActiveSync ............................................................................................. 20 Connecting the Device to Your Computer ............................................................................ 23 Synchronizing with Your Computer........................................................................... 24
ページ9に含まれる内容の要旨
Chapter 1 Getting Started Introducing the PA600 Thank you for purchasing the PA600 PDA Barcode Scanner. Your PA600 was designed for users who need a compact and durable PDA for data collection and real time transactions. The PA600 is a rugged, compact and lightweight palm-size com- puter using the Windows Mobile 5.0 / Windows CE 5.0 operating system, and incorporating an integrated bar code scanning laser device, color LCD with touchscreen, keypad, IrDA interface, and wireless communication
ページ10に含まれる内容の要旨
Features Audio Powerful System • Voice recording and playback • Microsoft Windows Mobile 5.0 / • MIC Windows CE 5.0 operating • Speaker system • Headset Connector • Intel PXA270 processor with speed • Receiver of up to 520 MHz Wireless Connectivity System Memory • 802.11b/g with diversity antenna • 64 MB SDRAM • Bluetooth wireless technology • 128 MB Flash ROM • Serial infrared port Display Expansion Slot • 3.5-inch QVGA LCD touch-sensi- SDIO slot tive screen Battery Life • 320 x 240 resolution
ページ11に含まれる内容の要旨
Chapter 1 Getting Started Package Contents After opening the box, ensure the following accessories for the PA600 are present: PA600 Terminal AC Adapter Battery Pack Stylus Quick USB Charging Elastic Stylus String CD-ROM Reference Cables Guide If anything is missing or appear damaged in any way, contact your dealer. 3
ページ12に含まれる内容の要旨
A Tour of the PA600 The following sections describe the main components and features of the PA600. Front Left View No. Component Description 1. Status indicator Indicates the battery charging and barcode scanning status. Green - Battery is fully charged, the device is running on battery power, or barcode scanning process is completed without error. Red - Battery is charging, barcode scanner is activated and processing. 2. Left scanner Press to activate the barcode laser scanner. trigger butt
ページ13に含まれる内容の要旨
Chapter 1 Getting Started Back View No. Component Description 9. Battery compartment Houses the removable and rechargeable 3.7V, 1950 mAH battery pack. 10. Battery compartment Opens the battery compartment. release latch 11. Reset button Press the end of the stylus into the button to reset your device. 12. Handstrap Enables you to securely hold the PA600 while using it. 13. Speaker Enables you to hear audio from the PA600. 14. Strap holder Attachment location for holding hand strap, carrying
ページ14に含まれる内容の要旨
Getting Started This section explains how to install and charge the battery, how to check battery status, how to turn on the PA600, and how to calibrate the screen. Installing the Battery WARNING!There is a risk of fire and burns if the battery pack is handled improp- erly. DO NOT disassemble, crush, puncture, short external contacts, or dispose the battery pack in fire or water. DO NOT attempt to open or service the battery pack. Dispose of used batteries according to local recycling guideli
ページ15に含まれる内容の要旨
Chapter 1 Getting Started 2. Position the battery pack, making sure the battery contacts are aligned with the contacts in the compartment and the battery is placed on top of the plastic tab, as shown in the following illustration. Contacts Plastic tab 3. Slide the battery pack into the battery bay while simultaneously pulling the plastic tab and securing clip until the battery clicks into place. Securing clip Plastic tab 4. Replace the battery compartment cover. 7
ページ16に含まれる内容の要旨
Charging the Battery Before using the PA600 for the first time, you need to charge it for about 16 hours. After that, you can charge the PA600 every day to recharge the battery to full capacity. Charge the PA600 using the USB charging cable or the docking station. CAUTION! Operating the PA600 for the first time without the AC adapter, and without fully charging the backup battery may result in loss of data stored in RAM memory. When the main battery is removed, the backup battery retains RA
ページ17に含まれる内容の要旨
Chapter 1 Getting Started Charging the Battery with the Docking Station 1. Plug the AC adapter cable into the power jack on the docking station, then connect the AC adapter into an electrical outlet. 2. Slide the device into the docking station until it clicks into place. 3. The connection is secure when the bottom edge of the device is aligned with the docking station, and the LED indicator on the device lights up red. LED Status LED Meaning PA600 Solid Red Charging Solid Green Charging com
ページ18に含まれる内容の要旨
Connecting the PA600 to a PC Use the USB cable to connect the PA600 to a PC to use with ActiveSync. 1. Press and hold the connector button on the USB charging cable and connect it to the PA600 (1). 2. Plug the USB connector into the USB port on the PC and connect the AC adapter into the USB connector (2). 3. Connect the AC adapter into an electrical outlet (3). 10 Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd
ページ19に含まれる内容の要旨
Chapter 1 Getting Started Turning the PA600 on for the First Time After you have initially charged your device for about 12 hours, the device is ready to be used. You can now start up your device where you’ll calibrate the display, learn some basic stylus usage, and set up the system time zone, date and time. Powering On 1. Turn on your device by pressing the power button on the front panel. NOTE: The PA600 screen ships with a protective plastic film. You may remove this if desired by peel
ページ20に含まれる内容の要旨
Calibrating the PA600 Screen The calibrate screen automatically appears when the unit is powered-on for the first time or after the system is reset. To calibrate the screen at any time, follow these instructions. 1. Tap Start → Settings, and then click the System tab. 2. Tap the Screen icon. 12 Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
