ページ1に含まれる内容の要旨
CD-R/RW SCSI Drive Unit
CD-R/RW SCSI Drive Unit
User’s Guide
Mode d’emploi
Bedienungsanleitung
Manual de instrucciones
Manuale d’istruzione
User’s Guide
Mode d’emploi
Bedienungsanleitung
Manual de instrucciones
©1999 by Sony Corporation
Rev. 1.0
Manuale d’istruzione
BKC: 98001684
ページ2に含まれる内容の要旨
This unit uses CD-R discs and CD-RW discs Owner’s Record with the following mark. The model and serial numbers are located on the top of the drive. Record these numbers in the spaces provided below. Refer to them whenever you call upon your sales representative regarding this product. Model No. __________________ Serial No. ___________________ This unit uses CD-ROM discs with the following mark. Safety Regulations When you use this unit as a CD player, use compact discs with the follo
ページ3に含まれる内容の要旨
Contents Introduction Introduction 5 Features Features..........................................................................................................5 This CD-R/RW drive has the following features: System Requirements for WINDOWS 95/98/NT............................................5 General Location and Function of Parts and Controls 6 5 1/4 inch half-height drive form factor. Front Panel / Rear Panel................................................................................6 Fas
ページ4に含まれる内容の要旨
Location and Function of Parts and Controls Precautions Installation Front Panel Avoid placing the drive in a location subject to: – high humidity – high temperature – excessive dust – mechanical vibration – direct sunlight. Only horizontal drive operation recommended, not vertical or tilted. Operation Do not move drive during operation, it may cause an error. Avoid sudden temperature changes, condensation may form inside the drive. Should ambient temperature suddenly change, wait at least 1 ho
ページ5に含まれる内容の要旨
Step 1: Opening the Computer Step 3: Finding the Connector First turn off computer and remove / unplug all power cables! The SCSI cable should have 1 or more unused connectors on the end Remove computer cover as directed in the User’s Manual. opposite the adapter, as shown, find a connector not in use. We recommend a connector at the very end of the 50 pin SCSI cable. Step 2: SCSI Configuration Locate the 50 pin SCSI cable in your computer. One end of the cable is connected to the SCSI host ada
ページ6に含まれる内容の要旨
The following table shows the function of each jumper. Step 5: Setting the Jumpers Set jumpers on rear of drive unit according to your computer configuration. Jumpers are factory preset as shown below. Jumper Function ACTIVE ON: Enables active termination TERM OFF: Disables active termination TEST ON: Enables test mode OFF: Enables normal operation ACTIVE TERM ID SELECT Assign the drive unit’s ID number by setting these TEST jumpers to ON or OFF. Do not assign the same ID 1 ID 2 ID 4 number as o
ページ7に含まれる内容の要旨
Step 6: Connecting the Drive Step 7: Mounting the Drive Attach flat SCSI cable to connector at rear of CD-RW drive. Insert the CD-RW drive into computer front as shown, routing cables accordingly. Secure drive to frame with appropriate screws. CD-R/W Drive Unit Pin 1 Interface Connector Power Supply Connector Audio Out Connector Red Edge Mounting Screws SCSI Flat Cable Flat Cable Audio Audio Cable Cable Note: Slide rails (not included) may be necessary if you cannot secure CD-RW drive. Refer to
ページ8に含まれる内容の要旨
Software Installation Please refer to CD-RW formatting software/CD manual for instruction on Step 9: Installation Review software installation. CD-RW formatting software must first be properly Now let us review the hardware installation process, assuring that: installed in order to write CD’s with this device. All connectors are properly connected. l Each SCSI device has its own unique SCSI ID number. l The last physical SCSI device on the bus is properly terminated. Red Edge Using Discs Notes
ページ9に含まれる内容の要旨
Operating the Drive Assure application software is installed before using the CD-RW drive. As the drive begins reading the Table of Contents (TOC) data, the busy indicator lights and remains illuminated until read is completed. When the busy indicator switches off, the drive is ready to receive commands, data may be retrieved from the disc. After loading a disc, Starting Up it takes a moment for the drive to become ready while Program Memory 1 Turn on the computer. Area is read. From this point,
ページ10に含まれる内容の要旨
Troubleshooting Technical Support Should problems occur while installing or operating the drive: If you require further support or service please contact your local Sony technical support professionals. Please verify the steps of this manual were carefully followed. If problem still exists, please confirm the items in ”Checklist“ below. For Europe (German or English) contact the hotline at: Tel.: +49 (0) 2389 - 951047 or SONY-HOTLINE@SUPLIE.COM (Monday – Thursday, 8:00 am – 4:30 pm / Friday, 8
ページ11に含まれる内容の要旨
Specifications General Host interface SCSI-2, single ended, 50 pin Audio Line out: 0.7 V at 47 kΩ Headphone: 0.55 V at 32 Ω Environmental conditions Relative humidity 10% to 90% (no condensation) Climate gradient 10°C/hour, 10% humidity/hour Temperatures Operating 5°C to 45°C (41°F to 113°F) Transport –40°C to 60°C (–40°F to 140°F) (72 hours max.) Storage –30°C to 50°C (–22°F to 122°F) (6 month max.) Design and specifications subject to change without notice. 20 Specifications n n n
ページ12に含まれる内容の要旨
3 146(5 / ) 4 11 41.4(1 /16) 7 21.9( / ) 8 10 13 ( /32) + 139.7 1 (5 /2) 0.5 0.4 1 ( / ) 1 32 ( /32) + 4 M3 mounting holes 4 trous à vis de montage M3 4 Schraubbohrungen M3 8 M3 mounting holes (4 on each side) 4 tornillos tipo M3 8 trous à vis de montage M3 (4 de chaque côté) 4 viti di fissaggio M3 8 Schraubbohrungen M3 (4 auf jeder Seite) 8 tornillos tipo M3 (4 a cada lado) 7 148 (5 / ) 8 8 viti di fissaggio M3 (4 per ogni lati) Dimension diagram Important: The overhang of the screws should no
