ページ1に含まれる内容の要旨
®
SELECTRONIC
7055.105 7055.205
7055.115 7055.215
Proximity Integrated Faucet
with Optional Above-Deck Mixing
7056.105 7056.205
®
7056.115 7056.215
• Flexible Selectronic Platform with Universal Sensor
• Easy installation. All electronics in the spout; nothing below deck.
• User adjustable above-deck mixing uses ceramic disc
valve for dependability & long life
• Mixing handle can be removed for one time temperature
setting during installation
• Available in DC (Battery) & AC versions
Produc
ページ2に含まれる内容の要旨
Base P r oduct Deck Plate Mixing Valve 6 6 Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. All American Standard Faucets Are Water Tested At Our Factory. UNPACKING Some Residual Water May Remain In The Faucet During Shipping. 1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose item
ページ3に含まれる内容の要旨
Roughing-in Dimensions Fig. 1 191mm (7-1/2) FINISHED WALL OR BACKSPLASH MIN. 1" CLEARANCE 191mm (7-1/2) 165mm 140mm (6-1/2) (5-1/2) MOUNTING SURFACE 66mm ( 2-5/8) 38mm 32mm (1-1/4) (1-1/2 ) GENERAL DESCRIPTION: Electronic faucet with proximity operation. Vandal 457mm resistant solid brass construction single post mounting. (18) Operates on DC (battery) or AC power. Inlets 3/8" compression, built-in checks, flexible stainless steel 18" reach inlet hoses for spout connection and In-line 3/8"
ページ4に含まれる内容の要旨
MAKE 3 WATER SUPPLY Fig. 2 CONNECTIONS; Fig. 2 1. Turn off hot and cold water supplies before beginning. 2. Connect HOSE ADAPTERS (3) to wall supplies (if 2 required). Connect FLEXIBLE SUPPLIES (1, 2) directly to HOSE ADAPTERS (3). 1 3. Connect left supply (Marked with a Red Stripe) to 3 Hot and right supply (Marked with Blue Stripe) to Cold supply. Use adjustable SEAL WASHER wrench to tighten connections. Do not over tighten. (SUPPLIED) HOT 4. Faucet supplies are 18" long from faucet
ページ5に含まれる内容の要旨
2 HOW TO CHANGE SENSOR Fig. 2 RANGE; (Factory set at 6") Fig. 2 1. Setting the Detection Zone (Distance): REMOVE Remove the FAUCET COVER (1) by unthreading the LEVER SCREW (2) and pulling off the LEVER 1 HANDLE (3). Unthread the FAUCET COVER SCREW REPLACE (4) at the back of the FAUCET. Pull FAUCET COVER (1) up and off. Fig. 2. 2. Disconnect the BLACK POWER SUPPLY 3 2 CONNECTOR (1) and reconnect. Fig. 3. 4 3. While the SENSOR CONTROL LED (2) is blinking slowly, place your hand 1 - 2 in.
ページ6に含まれる内容の要旨
3 HOW TO INSTALL AND CHANGE Fig. 5 BATTERY; Fig. 5 1. Remove the FAUCET COVER (1) by unthreading the LEVER SCREW (2) and pulling off the LEVER HANDLE (3). Unthread the FAUCET COVER SCREW (4) at the back of the FAUCET. Pull FAUCET COVER 1 (1) up and off. See Fig. 2 in this section. 2 2. Remove BATTERY HOLDER (1) from FAUCET BODY (2). 3. Remove old battery from the BATTERY HOLDER (1). 4. Install NEW BATTERY (3) into the BATTERY HOLDER (1). Replace BATTERY HOLDER (1) into the FAUCET BOD
ページ7に含まれる内容の要旨
5 HOW TO CLEAN FILTER SCREEN Fig. 9 ON SOLENOID VALVE; Fig. 9 & 10 1. Remove the FAUCET COVER (1) by unthreading the LEVER SCREW (2) and pulling off the LEVER HANDLE (3). Unthread the FAUCET COVER SCREW DISCONNECT WIRE CONNECTION (4) at the back of the FAUCET. Pull FAUCET COVER 1 (1) up and off. See Fig. 2 in this section. 2. Disconnect WIRE CONNECTION (1) to SOLENOID VALVE (2). Fig. 9. 3. Unthread SOLENOID VALVE (2) from VALVE BODY (3). Fig. 9. 4. Remove FILTER SCREEN (4) from base
ページ8に含まれる内容の要旨
7 CHANGE HOT LIMIT SETTING FROM 95% TO 85%; Fig. 13 2 1. Remove the FAUCET COVER (1) by unthreading the LEVER SCREW (2) and pulling off the LEVER HANDLE (3). Unthread the FAUCET COVER SCREW 3 (4) at the back of the FAUCET. Pull FAUCET COVER (1) up and off. See Fig. 2 in this section. 2. Replace LEVER HANDLE and rotate counter-clockwise to its stop position (100% cold). SLOT Remove HANDLE. 3. Pull out LIMITER STOP (1) from the VALVE STEM (2). 4. Rotate LIMITER STOP (1) 180 degrees
ページ9に含まれる内容の要旨
SELECTRONIC Proximity Integrated Faucet with Above-Deck Mixing PRODUCT NUMBERS 7055.105 7055.205 M900540-0020A 7055.115 7055.215 FAUCET COVER (LESS MIXING) 7056.105 7056.205 M900541-0020A 7056.115 7056.215 FAUCET COVER (FOR MIXING VALVE) A912790-0070A VALVE STEM O-RINGS A923654-0070A BATTERY 6VCR-P2 M964171-0070A 1.5 GPM AERATOR M964172-0070A M950514-0070A 0.5 GPM AERATOR BATTERY HOLDER M964188-0070A COLLAR NUT & TEMPERATURE LIMITER STOP M954483-0070A SOLENOID VALVE M964187-0020A LEVER ASSEMBL
