ページ1に含まれる内容の要旨
50SS018-060
50SX024-060
Single-Package Cooling Units
Installation, Start-Up and
Service Instructions
CONTENTS
Page
SAFETY CONSIDERATIONS .................1-12
General......................................1
RECEIVING AND INSTALLATION ...........13-26
Step 1 — Check Equipment..................13
• IDENTIFY UNIT
• INSPECT SHIPMENT
Step 2 — Provide Unit Support ..............13
• ROOF CURB
• SLAB MOUNT
Step 3 — Provide Clearances ................13
Step 4 — Rig and Place Unit.................13
• UN
ページ2に含まれる内容の要旨
REQUIREDCLEARANCESTOCOMBUSTIBLEMATERIAL —in.(mm) Unit Top ................................14 (356) Duct Side of Unit ............................2 (51) Side Opposite Ducts ........................14 (356) Bottom of Unit.................................0 Vertical Discharge First 12 in. (305) of Supply Duct .......1 (25) NECESSARY REQUIRED CLEARANCES — in. (mm) Between Units, Control Box Side ................42 (1067) Unit and Ungrounded Surfaces, Control Box Side ......36 (914) Unit and Block or
ページ3に含まれる内容の要旨
REQUIREDCLEARANCESTOCOMBUSTIBLEMATERIAL —in.(mm) Unit Top ................................14 (356) Duct Side of Unit ............................2 (51) Side Opposite Ducts ........................14 (356) Bottom of Unit.................................0 Vertical Discharge First 12 in. (305) of Supply Duct .......1 (25) NECESSARY REQUIRED CLEARANCES — in. (mm) Between Units, Control Box Side ................42 (1067) Unit and Ungrounded Surfaces, Control Box Side ......36 (914) Unit and Block or
ページ4に含まれる内容の要旨
REQUIRED CLEARANCES TO COMBUSTIBLE MATERIAL — in. (mm) Unit Top ....................................14 (356) CENTER OF GRAVITY (in./mm) Duct Side of Unit.................................2 (51) UNIT Side Opposite Ducts .............................14 (356) 50SS XY Z Bottom of Unit.....................................0 048 21.9/555 19.6/498 13.4/341 Vertical Discharge First 12 in. (305) of Supply Duct...............1 (25) 060 22.2/565 19.8/503 13.4/340 NECESSARY REQUIRED CLEARANCES — in. (mm) Betw
ページ5に含まれる内容の要旨
REQUIRED CLEARANCES TO COMBUSTIBLE MATERIAL — in. (mm) CENTER OF GRAVITY (in./mm) UNIT Unit Top..................................14 (356) 50SS XY Z Duct Side of Unit ..............................2 (51) Side Opposite Ducts ...........................14 (356) 048 21.7/550 19.7/501 15.7/400 Bottom of Unit ..................................0 060 22.0/560 19.9/506 15.7/399 Vertical Discharge First 12 in. (305) of Supply Duct ............1 (25) NECESSARY REQUIRED CLEARANCES — in. (mm) LEGEND Between
ページ6に含まれる内容の要旨
REQUIREDCLEARANCESTOCOMBUSTIBLEMATERIAL—in.(mm) LEGEND Unit Top ................................14 (356) CG — Center of Gravity NEC — National Electrical Code Duct Side of Unit ............................2 (51) COND — Condenser REQ’D — Required Side Opposite Ducts ........................14 (356) MAT’L — Material Bottom of Unit.................................0 Vertical Discharge First 12 in. (305) of Supply Duct .......1 (25) NECESSARY REQUIRED CLEARANCES — in. (mm) Between Units, Control Box
ページ7に含まれる内容の要旨
REQUIREDCLEARANCESTOCOMBUSTIBLEMATERIAL—in.(mm) LEGEND Unit Top ................................14 (356) CG — Center of Gravity NEC — National Electrical Code Duct Side of Unit ............................2 (51) COND — Condenser REQ’D — Required Side Opposite Ducts ........................14 (356) MAT’L — Material Bottom of Unit.................................0 Vertical Discharge First 12 in. (305) of Supply Duct .......1 (25) NECESSARY REQUIRED CLEARANCES — in. (mm) Between Units, Control Box
ページ8に含まれる内容の要旨
Fig. 8 — Dimensions; Units 50SX042-060 Without Base Rail 8
ページ9に含まれる内容の要旨
LEGEND CG — Center of Gravity NEC — National Electrical Code COND — Condenser REQ’D — Required MAT’L — Material REQUIRED CLEARANCES TO COMBUSTIBLE MATERIAL — in. (mm) Unit Top ........................................14 (356) Duct Side of Unit ...................................2 (51) Side Opposite Ducts ...............................14 (356) Bottom of Unit.........................................0 Vertical Discharge First 12 in. (305) of Supply Duct ...........1 (25) NECESSARY REQUIRED CLEARANC
ページ10に含まれる内容の要旨
Fig. 9 — Dimensions; Units 50SX042-060 With Optional Base Rail 10
ページ11に含まれる内容の要旨
LEGEND CG — Center of Gravity NEC — National Electrical Code COND — Condenser REQ’D — Required MAT’L — Material REQUIRED CLEARANCES TO COMBUSTIBLE MATERIAL — in. (mm) Unit Top ........................................14 (356) Duct Side of Unit ...................................2 (51) Side Opposite Ducts ...............................14 (356) Bottom of Unit.........................................0 Vertical Discharge First 12 in. (305) of Supply Duct ...........1 (25) NECESSARY REQUIRED CLEARANC
ページ12に含まれる内容の要旨
PART NUMBER ‘‘A’’ CPRFCURB001A00 89 [203] FLAT CPRFCURB002A00 119 [279] CURB CPRFCURB003A00 149 [356] NOTES: 1. Roof curb must be set up for unit being installed. 2. Seal strip must be applied as required for unit being installed. 3. Dimensions in [ ] are in millimeters. 4. Roof curb is made of 16 gage steel. 5. Attach ductwork to curb (flanges of duct rest on curb). 6. Service clearance 4 ft on each side. 7. direction of airflow. 8. Insulated panels, 1-in. thick, fiberglass 1-lb density. Fig. 10 —
ページ13に含まれる内容の要旨
RECEIVING AND INSTALLATION Step 1 — Check Equipment Do not restrict condenser airflow. An air restriction at either the outdoor-air inlet or the fan discharge can be IDENTIFYUNIT—Theunitmodelnumberandserialnum- detrimental to compressor life. ber are stamped on the unit identification plate. Check this information against shipping papers. Do not place the unit where water, ice, or snow from an overhang or roof will damage or flood the unit. Do not INSPECTSHIPMENT—Inspectforshippingdamagewhile insta
ページ14に含まれる内容の要旨
NOTICE TO RIGGERS Hook rigging shackles through holes in lifting brackets, as shown in Detail‘‘A,’’liftingbracketstobecenteredaroundtheunitcenterofgravity.Use wood top skid when rigging, to prevent rigging straps from damaging unit. All panels must be in place when rigging. SHIPPING WEIGHT A B C UNIT SIZE 50SS Lb Kg in. mm in. mm in. mm 3 1 018 260 118 36 ⁄4 934 18 457 24 ⁄8 613 3 3 1 024 289 131 36 ⁄4 934 16 ⁄4 426 24 ⁄8 613 3 5 1 030 306 139 36 ⁄4 934 16 ⁄16 415 24 ⁄8 613 3 1 1 036 322 146 36
ページ15に含まれる内容の要旨
Table 1 — Physical Data — Unit 50SS UNIT 50SS 018 024 030 036 042 048 060 REFRIGERANT R-22 Metering Device Acutrol™ System Charge (lb) 2.60 2.75 3.40 4.30 5.20 6.50 7.00 OPERATING WEIGHT (lb) Without Base Rails 208 237 254 270 300 332 359 With Optional Base Rails 228 257 274 290 320 352 379 COMPRESSOR TYPE Rotary Reciprocating Reciprocating Reciprocating Reciprocating Scroll Scroll EVAPORATOR FAN Centrifugal — Direct Drive Speeds 2 3332 2 2 Nominal Rpm 825 1075 1100 1100 1100 1100 1100 Diameter
ページ16に含まれる内容の要旨
andAirConditioningContractorsAssociation(ACCA)mini- Step5—SelectandInstallDuctwork— Thede- mum installation standards for residential heating and air sign and installation of the duct system must be in accor- conditioning systems. dancewiththestandardsoftheNFPA(NationalFireProtec- tion Association) for installation of nonresidence-type air • Secure all ducts to building structure. Flash, weather- conditioningandventilatingsystems,NFPA90Aorresidence- proof, and vibration-isolate duct openings in
ページ17に含まれる内容の要旨
ACCESS PANEL (REMOVE SCREWS) Fig. 15 — Evaporator Coil Access Panel Fig. 16 — Basepan Insulation Over Vertical Duct Opening 5. Remove indoor blower access panel (Fig. 18). 6. Disconnectevaporator-fanmotorleadsfromevaporator- fan relay and unit contactor. Carefully disengage wire tie containing evaporator-fan motor leads from the unit control box (Fig. 19). 7. Removescrews(Fig.20)securingevaporatorblowerhous- ingtoblowershelfandcarefullyslideoutblowerhous- ing.Thereisafillerbracketattachedtotheblo
ページ18に含まれる内容の要旨
Fig. 21 — Basepan Insulation Over Vertical Discharge Opening INDOOR BLOWER ACCESS PANEL (REMOVE SCREWS) Fig. 18 — Indoor Blower Access Panel WIRE TIE CONTACTOR RELAY Fig. 22 — Insulation and Cover Removed from Vertical Discharge Opening CONVERTING HORIZONTALDISCHARGE UNITS TO DOWNFLOW (VERTICAL) DISCHARGE — ICM (Inte- gratedControlMotor)UNITS—Unitsareshippedinahori- zontalconfiguration.Toconvertahorizontalunitfordown- flow (vertical) discharge, perform the following steps: Fig. 19 — Fan Motor Lead
ページ19に含まれる内容の要旨
7. Removescrewssecuringblowershelftoductpanel.Dis- 13. Orient blower housing for vertical airflow (blower mo- card the blower shelf. tor adjacent to horizontal duct opening). See Fig. 25. Reconnecttheplugassemblies.Slideblowerhousinginto 8. Locatelancesinbasepaninsulationthatareplacedover vertical opening making sure the flanges on the blower the perimeter of the vertical discharge opening cover side plates engage the tabs in the unit basepan. (Fig. 21). Resistance will be felt as the blower housi
ページ20に含まれる内容の要旨
4. Seethefollowingcaution.Usingremainingholesinduct flanges as templates, drill the remaining holes with the no. 26 (.147-in.) drill. BLOWER SHELF 1 Donotdrilldeeperthan ⁄2-in.intoshadedareashown in Fig. 26. Damage to refrigerant coil could result. FILLER BRACKET 5. Fullysecuretheductflangesusingtheremainingscrews provided. RACEWAY 3 The finished kit installation accommodates a 14 ⁄4-in. x 3 14 ⁄4-in. duct. PLUG ASSEMBLIES Fig. 24 — Filler Bracket and Blower Shelf 1 NOTE: Do not drill more than ⁄2-
