ページ1に含まれる内容の要旨
INTRODUCTION
CONTROLS,
INDICATORS AND
CONNECTORS
BASIC SYSTEM
CONNECTIONS AND
ADJUSTMENTS
POWER SUPPLY
Precautions For Use of the DV Connector
Be sure to follow the procedure outlined below when connecting.
PREPARATIONS
1. Turn ON the GY-DV500 and the equipment to be connected.
2. Set the VCR Setup Menu item No. 126 INPUT SELECT.
SETTING AND
3. Insert the videocassette.
ADJUSTMENTS
4. Connect the DV cable.
BEFORE SHOOTING
(If the procedure is performed in incorrect order, noise may appear in th
ページ2に含まれる内容の要旨
SAFETY PRECAUTIONS WARNING: FOR USA AND CANADA TO REDUCE THE RISK OF FIRE OR ELECTRIC IMPORTANT SAFEGUARDS U-ver. only SHOCK, DO NOT EXPOSE THIS APPLIANCE TO CAUTION RISK OF ELECTRIC SHOCK RAIN OR MOISTURE. DO NOT OPEN This unit should be used with 12V DC only. CAUTION: CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, 1. Read all of these instructions. To prevent electric shocks and fire hazards, do NOT use DO NOT REMOVE COVER (OR BACK). 2. Save these instructions for later use. any other pow
ページ3に含まれる内容の要旨
Thank you for purchasing the DV Camcorder GY-DV500. CONTENTS INTRODUCTION BASIC OPERATIONS MAIN FEATURES ............................................................... 4 ● This unit records and plays back in the SP mode. 5. PREPARATIONS This unit is a MiniDV video system format camcorder. Recording or playback in the LP mode is not possible. 5-1 Turning the Power ON .............................................. 39 1. INTRODUCTION Videocassettes which are not marked with the MiniDV ● In the cas
ページ4に含まれる内容の要旨
1. INTRODUCTION 1. INTRODUCTION 1. INTRODUCTION 1-1 Main Unit Configuration 1-2 Precautions for Proper Use 11. USING EXTERNAL COMPONENTS The GY-DV500 configuration is as shown below. ● Supply voltage ● Setup level (NTSC only) 11-1 Connecting a Video Component with DV Connector 64 Make sure that the power is between 11 V and 15 V DC. If The video signal of the unit's video output is provided with a 11-2 Connecting a PC ...................................................... 65 the power voltage
ページ5に含まれる内容の要旨
1. INTRODUCTION 1. INTRODUCTION 1-3 Routine and Periodical Maintenance 1-5 Battery Pack to be Used The GY-DV500 can use any of the following battery packs. The GY-DV500 incorporates precision mechanical parts, which will collect dirt, wear out and deteriorate as the unit is used. On the * An Anton-Bauer battery pack cannot be connected directly other hand, when the unit has been used for a long period in a normal environment, the heads, drums and tape transport mechanisms ● Flat shape type to
ページ6に含まれる内容の要旨
2. CONTROLS, INDICATORS AND CONNECTORS 2. CONTROLS, INDICATORS AND CONNECTORS 2-1 Front Section 2-1 Front Section (Cont’d) ACCU-FOCUS: [LENS] Lens control connector 4 • When this switch is set to "ACCU FOCUS" in the lower Connect 12-pin lens control cable from lens. position, the lens iris will be forced to open for Pin No. Function Pin No. Function approximately ten seconds. q • The depth of field can be reduced and the lens focusing 1 RET switch 7 IRIS position can be adjusted more accuratel
ページ7に含まれる内容の要旨
2. CONTROLS, INDICATORS AND CONNECTORS 2. CONTROLS, INDICATORS AND CONNECTORS 2-2 Right Side Section 2-2 Right Side Section [Camera Setting Section] [Camera Setting Section] [AUTO IRIS] Auto iris level switch [WHT.BAL] White balance switch 8 @ This switch selects the automatic iris adjustment Three white balance modes are selectable with this switch. reference value according to the condition in which the B : If white balance is performed with the OPERATE/WARNING 1 camera is used. switch in th
ページ8に含まれる内容の要旨
For servicing When replacing the Lithium Battery, see page 41 “Setting the Date and ← Time” and then set the date and time as described therein. 2. CONTROLS, INDICATORS AND CONNECTORS 2. CONTROLS, INDICATORS AND CONNECTORS 2-2 Right Side Section (Cont'd) 2-2 Right Side Section (Cont'd) [Audio Setting Section] [VCR Setup Block] ui ty CH-1 AUDIO CH-2 TC GENERATOR CH-1 CH-2 LEVEL OPERATE/WARNING OPERATE/WARNING AUTO PRESET FREE LIGHT LIGHT RESET ON REGEN REC OFF RESET ON MANUAL OFF AUTO AUDIO SEL
ページ9に含まれる内容の要旨
2. CONTROLS, INDICATORS AND CONNECTORS 2. CONTROLS, INDICATORS AND CONNECTORS 2-2 Right Side Section (Cont'd) 2-2 Right Side Section (Cont'd) [VCR Display Section] Warning indicators @ Tape transport direction indicators ^ One of the indicators lights according to the [AUTO OFF] indicator REV FWD Lights when a non-recoverable error (e.g. tape winding tape transport direction. is displayed in the record-pause error, drum stopped, etc.) occurs with the unit. This mode and in the still picture
ページ10に含まれる内容の要旨
For servicing The protocol of VCR control is not included in this service ← manual. 2. CONTROLS, INDICATORS AND CONNECTORS 2. CONTROLS, INDICATORS AND CONNECTORS 2-4 Top Section 2-3 Left Side Section PUSH q w i q EJECT DV CAMCORDER GY-DV500 PUSH OPEN LOG REW STOP FF PLAY STILL u w y LINE OUT Y/C OUT MONITOR OUT SYNC IN TEST OUT iy r u e t CH-1 CH-2 t e VTR w REMOTE MIC IN r LENS When used in a cold environment, the setting will be 3 Memo: [EJECT] switch 1 Cassette cover 1 minutes regardless o
ページ11に含まれる内容の要旨
2. CONTROLS, INDICATORS AND CONNECTORS 2. CONTROLS, INDICATORS AND CONNECTORS 2-5 Rear Section 2-5 Rear Section (Cont'd) !1 [CH-2 AUDIO IN] CH-2 audio input connector (XLR ! Battery holder lock release knob 6 This knob is used to open the battery case cover. Press the 3-pin) PUSH knob to open the cover. Connect the external audio equipment or microphone to this connector. Set the CH-2 AUDIO IN LINE/MIC select [BRAKER] @ switch according to the connected equipment. 9 0 The braker trips when th
ページ12に含まれる内容の要旨
2. CONTROLS, INDICATORS AND CONNECTORS 2. CONTROLS, INDICATORS AND CONNECTORS 2-6 Counter Display Contents 2-6 Counter Display Contents The counter display shows the following 4 types of information. The counter display shows the following 4 types of information. OPERATE/WARNING OPERATE/WARNING LIGHT LIGHT CH 1 OVER AUTO OFF DEW CH 1 OVER AUTO OFF DEW 1. Tape counter display ON RESET 40 30 20 10 0 dB RESET 40 30 20 10 0 dB ON OVER SERVO RF L i CH 2 OFF 1. Tape counter display CH 2 OVER SERVO RF
ページ13に含まれる内容の要旨
2. CONTROLS, INDICATORS AND CONNECTORS 2. CONTROLS, INDICATORS AND CONNECTORS 2-7 Lens (optional) 2-8 1.5-Inch Viewfinder (optional) [S14 x 7.3B12] IRIS mode switch [VF-P115B] Stopper screw 7 1 A: Activates the auto iris feature. This screw prevents the viewfinder from coming off the eq w M: Allows manual iris control. camera. 6 Momentary auto iris button Mounting guide 8 2 When the IRIS MODE switch is at "M", pushing this button To attach on the camera. 7 activates the Auto Iris Function whil
ページ14に含まれる内容の要旨
2. CONTROLS, INDICATORS AND CONNECTORS 2. CONTROLS, INDICATORS AND CONNECTORS 2-9 Indications in Viewfinder 2-9 Indications in Viewfinder (Cont'd) WARNING LED INDICATORS INSIDE THE VIEWFINDER 1 1 ACCU - FOCUS ACCU - FOCUS SCENE F I LE A WH I TE BA L A 2 2 FI LTER G G 3.2K SHUTTER 1/1000 3 3 F F GA I N 6 dB 4 4 I R I S LEVEL NORMAL The viewfinder has two LED indicators below the screen. These I I I R I S DETECT NORMAL 5 7 5 LEDs light or blink to indicate the present status of the camera SD
ページ15に含まれる内容の要旨
2. CONTROLS, INDICATORS AND CONNECTORS 2. CONTROLS, INDICATORS AND CONNECTORS 2. CONTROLS, INDICATORS AND CONNECTORS 2-9 Indications in Viewfinder (Cont'd) 2-9 Indications in Viewfinder (Cont'd) ● Status 1 Alarm Message Display In addition to the information on the Status 0 screen, this screen displays audio indicators and information on remaining tape, ACCU - FOCUS voltage and lens F-number. G Alarm message display Display Function Display position F The following alarm messages are displa
ページ16に含まれる内容の要旨
For servicing → See the service manual page 1-16 “1.11.7 Tripod base”. 2. CONTROLS, INDICATORS AND CONNECTORS 3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS 2-9 Indications in Viewfinder (Cont'd) 3-1 Basic System For information on connection with the individual attachments, refer to the page explaining the respective connection methods. Safety Zone Three types of safety zone items can be displayed in the viewfinder. Select the required one with the SAFETY ZONE item on the VF DISPLAY menu scree
ページ17に含まれる内容の要旨
3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS 3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS 3-2 Attaching the Zoom Lens (optional) 3-4 Attaching the Microphone (provided) Provided Microphone Connecting the provided microphone to the viewfinder. 1. Loosen the mount ring. The provided microphone is a phantom microphone. 1.3. 2. Connect the cable connector. 1. Loosen the stopper screw on the viewfinder. 3. Attach the lens with its pin aligned with the hole in the mount. 2.Attach the microphone to the
ページ18に含まれる内容の要旨
CR2032 CR2032 CR2032 For servicing → See the service manual page 1-16 “1.11.7 Tripod base”. 3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS 3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS 3-6 Attaching the Tripod Base (provided) 3-7 Inserting and Replacing Backup Lithium Batteries The GY-DV500 uses a lithium battery for backup of the time code data. Install the provided lithium battery before actually using the Use the provided tripod base to place the camera on a tripod. unit. 1. Attach the tripod ba
ページ19に含まれる内容の要旨
4. POWER SUPPLY 4. POWER SUPPLY The GY-DV500 is operable with AC power supply or battery pack. 4-2 Battery Pack Operation (Cont'd) 4-1 AC Operation Attaching a Flat Shape Type Battery Pack Use the JVC AA-P250 AC power adapter (max. rated output 12.5 V DC, 3.5 A) as the AC power supply. 1. Open the battery case cover while pushing the lock release lever. Do not use any power source with large fluctuations in the 2. Insert the battery pack into the battery case with its electrodes power source v
ページ20に含まれる内容の要旨
4. POWER SUPPLY 4. POWER SUPPLY 4-2 Battery Pack Operation (Cont'd) 4-2 Battery Pack Operation (Cont'd) REMAINING BATTERY POWER DISPLAY Using an Anton-Bauer Battery Pack WARNING To display the remaining battery power accurately, set the To use an Anton-Bauer battery pack (Propack 13/14, Trimpack 13/14, Magnum 13/14, Compack 13/14 Series), it is necessary to indicator VCR Setup Menu item No. 396 BATTERY TYPE according detach the battery case from the GY-DV500 and replace it with the Anton-Bauer
