EMC CX500の取扱説明書

デバイスEMC CX500の取扱説明書

デバイス: EMC CX500
カテゴリ: ポータブル記憶デバイス
メーカー: EMC
サイズ: 1.13 MB
追加した日付: 12/27/2013
ページ数: 36
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスEMC CX500の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、EMC CX500に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書EMC CX500をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書EMC CX500のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - EMC CX500の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
EMC CX500 取扱説明書 - Online PDF
Advertisement
« Page 1 of 36 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書EMC CX500を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書EMC CX500の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

EMC CLARiiON
CX300, CX500, and CX700
Storage Systems
Initialization Guide
P/N 300-001-272
REV A01
November 26, 2003
This guide explains the initial software setup procedure for the
®
CLARiiON CX300, CX500, and CX700 storage systems. An authorized
EMC service provider will perform these procedures at the customer
site.
Topics include
◆ Initialization Overview.........................................................................2
◆ Requirements for Initial Setup.............................

ページ2に含まれる内容の要旨

Initialization Overview Initialization Overview This section provides an overview of the initialization procedures described in this guide. Tasks highlighted with grey in the checklist should be completed before the service provider arrives at the customer site. Task Procedure 1 Prerequisites ❑ Verify requirements for initial setup (page 3). If your service laptop is not set up for dial-up PPP support or dial-up networking, you must complete the following (page 5): ❑ Set up the dial-up PPP

ページ3に含まれる内容の要旨

Requirements for Initial Setup Requirements for Initial Setup To set up and initialize the storage systems, you will need the following: General Requirements ❑ A CX700, CX500, or CX300 storage system with two storage ™ processors (SPs) that have the required FLARE software and ® EMC Navisphere Agent installed on them. ™ Note Navisphere is a member of the EMC ControlCenter family of products. ❑ A NULL modem cable, with 9-pin, female-male to female-male connectors (supplied with each storage

ページ4に含まれる内容の要旨

Requirements for Initial Setup Service Laptop Requirements Initializing the storage processor enclosure and the accompanying DAE2 disk enclosures requires a directly connected computer — usually a laptop model — that we refer to as a service laptop. ❑ A Windows operating system, as indicated in the EMC Navisphere Manager 6.X Release Notes. ❑ A supported web browser, as indicated in the EMC Navisphere Manager 6.X Release Notes. ❑ Java 2 Runtime Environment, as indicated in the EMC Navisphere

ページ5に含まれる内容の要旨

Setting Up the Service Laptop Setting Up the Service Laptop The PPP-capable (Point-to-Point Protocol) service laptop can be any computer that satisfies the requirements described on the previous page. The service laptop COM port modem type must be set to Dial-Up Networking Serial Cable between 2 PCs. This is the most flexible modem type, and allows either a NULL modem cable or actual modem to connect to the laptop and SP. If the laptop uses a physical modem, configure the modem for the Phy

ページ6に含まれる内容の要旨

Setting Up the Service Laptop Setting Up the Dial-Up PPP Support (Windows 2000 Environment) If Communication cable between two computers is not installed and set up, install it and set it up as follows: 1. Follow the path: Start > Settings > Control Panel > Phone and Modem Options 2. If your laptop has a modem, then under the Modems tab, note which port your current modem is using. 3. Click Add. 4. Select Don't Detect my Modem; I will select it from a list. 5. Click Next. An Add/Remove Hardwa

ページ7に含まれる内容の要旨

Setting Up the Service Laptop Setting Up Dial-Up Networking (Windows 2000 Environment) 1. Follow the path: Start > Settings > Control Panel > Network and Dial Up Connections > Make New Connection The Network Connection Wizard opens. 2. Click Next to begin. 3. Click Connect directly to another computer, then click Next. 4. Click the Guest button, then click Next. The Select a Device list is displayed. 5. From the Select a Device list, select Communications between two computers (COM 1) or selec

ページ8に含まれる内容の要旨

Setting Up the Service Laptop 15. Click the Networking tab. PPP: Windows 95/98/NT 4/2000, Internet should appear in the Type of dial-up server I am calling list. 16. Click Settings. 17. Make sure that Enable LCP extensions and Enable software compression are checked, then click OK. 18. Highlight Internet Protocol (TCP/IP). 19. Click Properties. 20. Select Obtain an IP address automatically and Obtain DNS server address automatically. 21. Click Advanced. Make sure that Use IP header compressio

ページ9に含まれる内容の要旨

Setting Up the Service Laptop Setting Up the Dial-Up PPP Support (Windows NT 4.0 Environment) 1. If Dial-Up Networking between 2 PCs is not installed and set up, install it and set it up as follows: a. Follow the path: Start > Settings > Control Panel > Modems b. If your laptop has a modem, then under the General tab of Modem Properties, note which port your current modem is using. c. Exit, then click Add. d. Select the Don't Detect my Modem; I will select it from a list check box. e. Click

ページ10に含まれる内容の要旨

Setting Up the Service Laptop 2. Configure the serial connection for remote access (RAS) by doing the following: a. In the Add RAS Device dialog box, select the dialup networking serial cable with the correct COM port noted in step 1i. b. Click OK. 3. From the Remote Access Setup dialog box, select the dialup networking serial cable with the correct COM port. 4. Click Configure. 5. In the Port Usage dialog box, select dial out only. 6. Click OK. 7. Click Continue to restart the computer.

ページ11に含まれる内容の要旨

Setting Up the Service Laptop 7. Clear the check box Use another port if busy. 8. Click the Server tab. 9. Set the Dial-up server type to be PPP: Windows NT, Windows 95 Plus, Internet. 10. In the Network Protocols dialog box, select TCP/IP. 11. Click TCP/IP Settings... and do the following in the PPP TCP/IP Settings dialog box: a. Select the Server assigned IP address option. The SP will provide the address for the service laptop. b. Select the Server assigned name server addresses check

ページ12に含まれる内容の要旨

Initializing the Storage System Initializing the Storage System This section describes how to set critical startup parameters on the storage system’s storage processors (SPs). Before you begin the initialization process, have the network administrator at your facility assign IP addresses for the storage system, and complete the following worksheet. You will need this information to complete the system setup. Table 2 Initialization Worksheet SP A SP B Hostname __________________________ ____

ページ13に含まれる内容の要旨

Initializing the Storage System Initialization Steps Follow the steps below to initialize the storage system from the service laptop. These instructions assume that you are starting with SP A. However you can start the initialization process with either SP. 1. Connect the NULL modem cable between the laptop serial port (COM 1) and the SP A service port (|0|0|on a CX700, or on a CX500 SP or CX300 SP), as shown in Figure 1. For a CX500, you will need the RJ45/DB9 serial adapter that shipped

ページ14に含まれる内容の要旨

Initializing the Storage System 3. Depending on your operating system, do one of the following: For Windows 2000 a. On the laptop, select Start > Settings > Network and Dial up Connections. Select the connection name that you assigned when you set up dial-up networking. b. In the Connect dialog box, log in as user clariion with password clariion!. c. Click Connect and click OK on the Connection Complete dialog box. For Windows NT 4.0 a. On the laptop, select My Computer > Dial-up Networking

ページ15に含まれる内容の要旨

Initializing the Storage System Figure 2 Storage Processor Networking Configuration Setup Screen (SP A) EMC CLARiiON CX300, CX500, and CX700 Initialization Guide 15

ページ16に含まれる内容の要旨

Initializing the Storage System 5. Specify the following for SP A: a. IP address b. Hostname c. Subnet Mask d. Gateway address for SP A e. Peer IP address for SP B f. If desired, for example, for added security (see the caution below), change the management port setting to 2162/2163. CAUTION ! Be sure that this is the management port whose setting you want to change. If you later want to change it back, you must remove the node from its domain before you can change its port setting from the

ページ17に含まれる内容の要旨

Initializing the Storage System Figure 3 Network Configuration Confirmation Screen (SP A) 8. Remove the NULL modem cable from SP A and connect it between the laptop serial port (COM 1) and the SP B service port (|0|0|, or ). 9. Depending on your operating system, do one of the following: For Windows 2000 a. On the laptop, select Start > Settings > Network and Dial up Connections. Select the connection name that you assigned when you set up dial-up networking. b. In the Connect to dialog box,

ページ18に含まれる内容の要旨

Initializing the Storage System For Windows NT 4.0 a. On the laptop, select My Computer > Dial-up Networking. Select the connection name that you assigned when you set up dial-up networking. b. Select the phonebook entry you created when you set up the laptop in the previous section. c. Click Dial. d. In the Connect to dialog box, log in as user clariion with password clariion!. Ignore the Domain field. e. Click OK. 10. Open a supported browser, and enter the following URL: 192.168.1.1/setup

ページ19に含まれる内容の要旨

Initializing the Storage System Figure 4 Storage Processor Networking Configuration Setup Screen (SP B) EMC CLARiiON CX300, CX500, and CX700 Initialization Guide 19

ページ20に含まれる内容の要旨

Initializing the Storage System 12. Specify the following for SP B: a. IP address b. Hostname c. Subnet mask d. Gateway address for SP B e. Peer IP address for SP A f. If desired, for example, for added security (see the caution below), change the management port setting to 2162/2163. CAUTION ! Be sure that this is the management port whose setting you want to change. If you later want to change it back, you must remove the node from its domain before you can change its port setting from th


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 EMC 69001166 取扱説明書 ポータブル記憶デバイス 0
2 EMC CX700 取扱説明書 ポータブル記憶デバイス 8
3 EMC CX300 取扱説明書 ポータブル記憶デバイス 18
4 EMC CX500 ユーザーマニュアル Server 0
5 Sony SDZ-100 取扱説明書 ポータブル記憶デバイス 1
6 Sony Ait-1 Tape Cartridge SDX135CAWW 取扱説明書 ポータブル記憶デバイス 1
7 Sony 取扱説明書 ポータブル記憶デバイス 1
8 Sony Micro Vault Mach USM8GQ 8 GB USB 3.0 Flash Drive USM8GQ/S 取扱説明書 ポータブル記憶デバイス 1
9 Sony SDX-400 取扱説明書 ポータブル記憶デバイス 2
10 Sony Dvcam Cassette PDV64N PDV64N 取扱説明書 ポータブル記憶デバイス 1
11 Sony SDX-410 取扱説明書 ポータブル記憶デバイス 1
12 Sony Ait-1 Tape Cartridge SDX1-35C 取扱説明書 ポータブル記憶デバイス 1
13 Addonics Technologies ST4ESA 取扱説明書 ポータブル記憶デバイス 1
14 Addonics Technologies ST4US-B 取扱説明書 ポータブル記憶デバイス 1
15 Addonics Technologies ST6ESA 取扱説明書 ポータブル記憶デバイス 1