ページ1に含まれる内容の要旨
R9921
Multi-band RDS digital preset world radio
R 9921 Power
Display
ATS - FM/MW
FM/MW/SW Preset +
Meter -SW Time Set
Hour
BANDS
FM ST./Mono
Memo Tuning +
StandBy
Min
M
AUT AUTO O TUNING TUNING SYSTEM SYSTEM
Please read this manual before use
ROBERTS
Sound for Generations
ページ2に含まれる内容の要旨
Contents Features ....................................................... 1 FM mono/stereo button ............................ 19 Control locations........................................ 2 Setting the sleep timer ............................. 19 Display back light ...................................... 20 Display information.................................... 4 Installing batteries...................................... 5 Lock button ................................................ 20 Battery r
ページ3に含まれる内容の要旨
Features Large easy to read Liquid Crystal Display (LCD) Wake to radio or buzzer alarms. showing station name, frequency, time, memory location and function status. Humane wake system - buzzer alarm gradually increases in volume. RDS station name display. Adjustable sleep timer allows you to fall asleep Twenty seven memory presets offer instant to music. access to your favourite stations on MW, SW and FM. Snooze function - turns off alarm for five minutes. Automatic time set via RDS signal. ATS
ページ4に含まれる内容の要旨
Controls 1. ATS/SW band select 123 4 5 2. Liquid crystal display. 3. Preset/Hour - button. R 9921 Power 4. Preset/Hour + button. 5. Power/Sleep button. 6. Display button. Display 6 7. Time set button. ATS - FM/MW + 8. Standby button. FM/MW/SW Preset Meter -SW Time Set Hour BANDS 7 9. Tuning/Minute + button FM ST./Mono 10. Tuning/Minute - button Memo Tuning + StandBy Min 11. Memory button. M 8 12. Waveband button. AUT AUTO O TUNING TUNING SYSTEM SYSTEM 13. Lock button. 14. Stereo/Mono button 13 1
ページ5に含まれる内容の要旨
18 19 20 15 15. Clock auto adjust switch. 16. Headphone socket. 17. DC input socket. 16 18. Telescopic aerial. 19. Light button. 17 21 20. Tone control switch. 21. Volume control. If you need any further advice, please call our Technical Helpline on :- 3 020 8758 0338 (Mon-Fri)
ページ6に含まれる内容の要旨
Display A BC DE F G N H I M J L K A. Alarm indicators F. Time. K. Memory number. B. RDS indicator. G. Key lock indicator. L. Memory indicator. C. Sleep time indicator. H. Low battery indicator. M. Frequency and text indicators. D. Snooze indicator. I. SW band N. Stereo indicator. E. AM/PM indicators. J. Frequency units. 4
ページ7に含まれる内容の要旨
Installing batteries 1. Position the radio face down on soft surface. 2. Press the catch as shown and slide in the direction of the arrow. 3. Lift out the battery cover 4. Insert 4 x LR6 (AA) size batteries as shown in the diagram. 5. Replace the battery cover. If you need any further advice, please call our Technical Helpline on :- 5 020 8758 0338 (Mon-Fri)
ページ8に含まれる内容の要旨
Battery replacement The battery indicator will appear in the display immediately your radio is switched off. Batteries should be replaced when the indicator shows less than 3. After removing batteries you have approximately 3 minutes to replace the batteries after which clock and memory information will be lost. When the low battery indicator appears in 123 display replace batteries immediately. Setting the clock automatically The clock time can be set automatically when receiving an RDS stat
ページ9に含まれる内容の要旨
4. Press and hold down the Tuning up or down buttons until the frequency in the display begins to change rapidly, release the button. 5. The radio will now start to search the FM waveband and will stop when it finds a station of sufficient strength. If the station is of sufficient strength the symbol will light up in the liquid crystal display. 6. Slide the Clock auto adjust switch to the ‘On’ position. 7. The time segments --:-- will flash in the liquid crystal display indicating that the ra
ページ10に含まれる内容の要旨
Setting the clock time manually When batteries are installed for the first time the display will show - - : - -. Time can be manually set with the radio switched on or off. The clock uses the 24 hour system e.g. 2:00pm is shown as 14:00. 1. Slide the Clock auto adjust switch to the ‘Off’ position 2. Press and release the Time set button , the display will show ‘TIME SET’ . 3. The clock uses the 24 hour system e.g. 2:00pm is shown as 14:00. Set the correct hour using the Hour + and - buttons. 4.
ページ11に含まれる内容の要旨
Setting the buzzer alarm Note: Clock uses 24 hour system. 1. Repeatedly press and release the Standby button until the display shows ‘Buzzer’. 2. Whilst the display symbol and alarm time are flashing set the required hour using the Hour + and - buttons. 3. Set the required minute using the Minute + and - buttons. Press and release the Standby button to complete alarm setting. 4. At the preselected time the alarm will sound. The alarm may be turned off for 24 hours by pressing the Power button.
ページ12に含まれる内容の要旨
Setting the radio alarm Note: Clock uses 24 hour system. 1. Repeatedly press and release the Standby button until the display shows ‘Last CH’. 2. Whilst the display symbol is flashing set the required hour using the Hour + and - buttons. 3. Set the required minute using the Minute + and - buttons. Press and release the Standby button to complete alarm setting. 4. At the preselected time the radio will switch on to the last station listened to. The alarm may be turned off for 24 hours by press
ページ13に含まれる内容の要旨
Search tuning 1. Switch on your radio by pressing the Power button. 2. Select the required waveband by repeat pressing of the Bands button. The waveband selected will appear in the display. On FM and SW fully extend the Telescopic aerial. On MW rotate your radio for best reception. 3. Press and hold down either the Tuning + or - buttons until the frequency in the display begins to change rapidly. Release the button. 4. Your radio will scan the selected waveband, stopping each time it finds a st
ページ14に含まれる内容の要旨
Manual tuning 1. Switch on your radio by pressing the Power button. 2. Select the required waveband by repeat pressing of the Bands button. The waveband selected will appear in the display. On FM and SW fully extend the Telescopic aerial. On MW rotate your radio for best reception. 3. A single press on either the Tuning + or - buttons will change the frequency up or down. The frequency steps are:- FM 50kHz, MW 9kHz or 10kHz and SW 5kHz. Adjust the Volume and Tone controls to the required sett
ページ15に含まれる内容の要旨
MW (AM) tuning step size In Europe and other parts or the world MW tuning steps are 9kHz, in America the MW tuning step size is 10kHz. To change the MW tuning step size from 9KHz to 10KHz proceed as follows:- 1. Switch on your radio and select the MW waveband. 2. Press and hold down the Display button until the display shows 10 kHz. 3. Press the Display button to confirm the setting. 4. To change back to 9kHz steps - press and hold down the Display button until the display shows 9 kHz. 5. Pr
ページ16に含まれる内容の要旨
Presetting stations You may store up to 9 stations on FM, 9 on MW and 9 on SW giving a total of 27 preset stations. 1. Tune into the required station using one of the tuning methods previously described. 2. Press and release the Memo button, the word SAVE - -> will appear in the display. 3. Select the preset under which you wish to store the station using the Preset + and - buttons. 4. Press and release the Memo button to store the station. The preset number will now appear at the bottom of the
ページ17に含まれる内容の要旨
Recalling a preset station 1. Switch on your radio using the Power button. 2. Select the desired waveband using the Bands button. 3. Press Preset + or - buttons to cycle through the available preset stations. Memory scan Your radio is equipped with a Memory scan facility. 1. Press and hold down either the Preset + or - buttons for at least 2 seconds to start memory scan. Your radio will scan the available memories pausing for a few seconds on each one. To stop memory scan press either the Pr
ページ18に含まれる内容の要旨
ATS (Automatic Tuning System) The automatic tuning system will scan the selected waveband and automatically store stations in the memory presets. note: ATS operates on FM an MW bands only - activating the ATS function will overwrite any stations previously stored in the memory presets 1. Select the required waveband by pressing the Bands button. 2. Press and hold down the ATS button until frequency digits in the display begin to change rapidly. Your radio will scan the selected waveband and auto
ページ19に含まれる内容の要旨
Operating your radio using RDS (Radio data system) The Radio Data System (RDS) is a system in which inaudible digital information is transmitted in addition to the normal FM radio programme. 1. Switch on your radio and select the FM waveband. 2. Tune into a station, the display will indicate frequency for a few seconds and then change to show the station name. The symbol will appear in the display ST 3. If the station does not carry RDS information only the station frequency will be shown. MH
ページ20に含まれる内容の要旨
Display Modes (FM only) 1. Whilst tuned to a station displaying its RDS station name, you can change between station name and ST frequency by pressing and releasing the Display button. 2. The display will show the stations frequency for 123 M approximately 5 seconds before reverting to showing station name ST MHz M123 ST M123 18
