Agilent Technologies 6011aの取扱説明書

デバイスAgilent Technologies 6011aの取扱説明書

デバイス: Agilent Technologies 6011a
カテゴリ: 電源
メーカー: Agilent Technologies
サイズ: 2.1 MB
追加した日付: 12/30/2013
ページ数: 126
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスAgilent Technologies 6011aの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Agilent Technologies 6011aに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Agilent Technologies 6011aをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Agilent Technologies 6011aのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Agilent Technologies 6011aの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Agilent Technologies 6011a 取扱説明書 - Online PDF
Advertisement
« Page 1 of 126 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Agilent Technologies 6011aを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Agilent Technologies 6011aの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

SERVICE MANUAL
AUTORANGING
DC POWER SUPPLY
AGILENT MODELS 6010A, 6011A,
6012B and 6015A
Agilent Part No. 5964-8275
FOR INSTRUMENTS WITH SERIAL NUMBERS
Agilent Model 6010A; Serials US37110171 and above
Agilent Model 6011A; Serials US35460156 and above
Agilent Model 6012B; Serials US35430336 and above
Agilent Model 6015A; Serials US37050146 and above
For instruments with higher serial numbers, a change page may be included.
Microfiche Part No. 5964-8276 Printed in

ページ2に含まれる内容の要旨

CERTIFICATION Agilent Technologies certifies that this product met its published specifications at time of shipment from the factory. Agilent Technologies further certifies that its calibration measurements are traceable to the United States National Institute of Standards and Technology, to the extent allowed by the Institute’s calibration facility, and to the calibration facilities of other International Standards Organization members. WARRANTY This Agilent Technologies hardware product is war

ページ3に含まれる内容の要旨

SAFETY SUMMARY The following general safety precautions must be observed during all phases of operation, service and repair of this instrument. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture, and intended use of the instrument. Agilent Technologies, Inc. assumes no liability for the customer's failure to comply with these requirements. BEFORE APPLYING POWER. Verify that the product is set to match the a

ページ4に含まれる内容の要旨

Safety Symbol Definitions Symbol Description Symbol Description Direct current Terminal for Line conductor on permanently installed equipment Alternating current Caution, risk of electric shock Both direct and alternating current Caution, hot surface Three-phase alternating current Caution (refer to accompanying documents) Earth (ground) terminal In position of a bi-stable push control Protective earth (ground) terminal Out position of a bi-stable push control (Intended for connection to externa

ページ5に含まれる内容の要旨

TABLE OF CONTENTS Introduction ............................................................................................................................................................................ 7 Scope .................................................................................................................................................................................... 7 Calibration and Verification ............................................................................

ページ6に含まれる内容の要旨

DC Power Conversion Subsystem...................................................................................................................................... 54 Output Subsystem............................................................................................................................................................... 54 The Front Panel Board.....................................................................................................................................

ページ7に含まれる内容の要旨

1 Introduction Scope This manual contains information for troubleshooting the Agilent Models 6010A, 6011A, 6012B, or 6015A 1000W Autoranging Power Supply to the component level. Wherever applicable, the service instructions given in this manual refer to pertinent information provided in the Operation Manual. Both manuals cover Agilent Models 6010A/11A/12B/15A; differences between models are described as required. The following information is contained in this manual. Calibration and Verificatio

ページ8に含まれる内容の要旨

Manual Revisions Agilent Technologies instruments are identified by a 10-digit serial number. The format is described as follows: first two letters indicate the country of manufacture. The next four digits are a code that identify either the date of manufacture or of a significant design change. The last four digits are a sequential number assigned to each instrument. Item Description US The first two letters indicates the country of manufacture, where US = USA; MY = Malaysia. 3648 This is a cod

ページ9に含まれる内容の要旨

2 Calibration and Verification Introduction This section provides test and calibration procedures. The operation-verification tests comprise a short procedure to verify that the unit is performing properly, without testing all specified parameters. After troubleshooting and repair of a defective power supply you can usually verify proper operation with the turn-on checkout procedure in the Operating Manual. Repairs to the A1 main board and the A2 control board can involve circuits which, althoug

ページ10に含まれる内容の要旨

Table 2-1. Test Equipment Required TYPE REQUIRED CHARACTERISTICS USE RECOMMENDED MODEL Oscilloscope Sensitivity: 1mV P,T Agilent 1740A Bandwidth: 20MHz & 100MHz Input: differential, 50Ω & 10MΩ Isolation Transformer 100VA 4KVA minimum T RMS Voltmeter True rms, 10MHz bandwidth P Agilent 3400A Sensitivity: 1 mV Accuracy: 5% Logic Pulser 4.5 to 5.5Vdc @ 35mA T Agilent 546A Multimeter Resolution: 100nV P,A,T Agilent 3456A Accuracy: 0.0035%, 6½ digit CC PARD Test No saturation at: P Tektronix P6303 C

ページ11に含まれる内容の要旨

Table 2-1. Test Equipment Required (continued) TYPE REQUIRED CHARACTERISTICS USE RECOMMENDED MODEL Load Resistors P,A 40Ω , ±1%, 1000W (6015A) 250Ω , ±1%, 1000W Current-Monitoring Value: P,A Resistors 6010A 100mV @ 10A (10mΩ must be capable of 20Amps) Accuracy: 0.02% ** TC: 10ppm/°C 6011A 50mV @100A (0.5mΩ ) Accuracy: 0.05% ** TC: 30ppm/°C 6012B 50mV @ 50A (1.0mΩ ) Accuracy: 0.02% ** TC: 30ppm/°C 6015A 0.1Ω , 15A, ±0.04%** Calibration and Test A,T Value: 50Ω , 5%, 40W Resistors 2KΩ , 0.01%,

ページ12に含まれる内容の要旨

Initial Setup Maintenance described herein is performed with power supplied to the instrument, and protective covers removed. Such maintenance should be performed only by service trained personnel who are aware of the hazards involved (for example, fire and electrical shock). Turn off ac power when making or removing connections to the power supply. Where maintenance can be performed without power applied, the power should be removed. a. Unplug the line cable and remove the top cover by removi

ページ13に含まれる内容の要旨

Table 2-2. Calibration Procedure (continued) TEST TESTED TEST POINTS TEST SEQUENCE AND ADJUSTMENTS EXPECTED VARIABLE RESULTS V-MON V-MON VM ( + ) a. Set voltage and current controls to minimum 0 ± 80µ V Zero M ( - ) settings. Adjust. b. Disable power supply as in Initial Setup step i. c. Short circuit output terminals and connect the DVM between test points. Turn on power supply. d. Adjust V-MON Zero trim pot A2R22 to voltage range specified in the results. Common Residual VM ( + ) a. Set volt

ページ14に含まれる内容の要旨

Table 2-2. Calibration Procedure (continued) TEST TESTED TEST POINTS TEST SEQUENCE AND ADJUSTMENTS EXPECTED VARIABLE RESULTS Power V(OUT) a. Perform I-MON F/S Adjust before Limit I(OUT) proceeding. Adjust. b. Connect the unit to the ac power line via a variable transformer. Set input power rail to 240Vdc; DVM ( + ) on rear of A1R3 and DVM (-) to rear of A1R1. Note that power rail must be maintained at 240Vdc during calibration. WARNING The inner cover must be removed to connect the voltmeter. D

ページ15に含まれる内容の要旨

Table 2-2. Calibration Procedure (continued) TEST TESTED TEST POINTS TEST SEQUENCE AND ADJUSTMENTS EXPECTED VARIABLE RESULTS Power Limit h. Turn A2R26 (upper knee) fully counter Adjust clockwise. Turn on the supply and set voltage (continued) at 200V (6010A), 20V (6011A), 60V (6012B), 500V (6015A), and current at 5.25A (6010A), 56A (6011A), 19A (6012B) 2.25A (6015A), using DISPLAY SETTINGS. i. Turn A2R26 (upper knee) clockwise until CV LED lights. Output should be 200 ± 2V (6010A), 20 ±0.5V (60

ページ16に含まれる内容の要旨

Table 2-3. Guide to Recalibration After Repair Printed Circuit Block Name Circuit Within Ref. Perform These Board Designator Procedures* A1 Main Board R11 3 then 4 R13 (6011A) A1 Main Board T1, T2 5 A5 Diode Board CR4 5 CR5, CR1 (6011A) A2 Control Board Constant Voltage All Except Current All 1 then 2 (CV) Circuit Source A2 Control Board Constant Voltage Current Source All 6 (CV) Circuit A2 Control Board Constant Current All 3 then 4 (CC) Circuit A2 Control Board Power Limit All 5 Comparator A2

ページ17に含まれる内容の要旨

for the electronic load in the following tests: CV Source Effect (Line Regulation) CC Load Effect (Load Regulation) Temperature Coefficient (6015A) Drift (stability ) (6015A) You may substitute: 40Ω 1000W load resistor (6010A) 0.058Ω 1000W load resistor (6011A) 3.4Ω 1000W load resistor (6012B) 40Ω 1000W load resistor (6015A) in these tests: CV Load Effect (Load Regulation) CV PARD (Ripple and Noise) CC Source Effect (Line Regulation) CC PARD (Ripple and Noise) The substitution of the load resist

ページ18に含まれる内容の要旨

Constant Voltage (CV) Tests CV Setup. If more than one meter or a meter and an oscilloscope are used, connect each to the + S and - S terminals by a separate pair of leads to avoid mutual coupling effects. Connect only to + S and -S (except for peak-to-peak PARD) because the unit regulates the output voltage between + S and - S, not between + OUT and -OUT. Use coaxial cable or shielded 2-wire cable to avoid pickup on test leads. For all CV tests set the output current at full output to assure CV

ページ19に含まれる内容の要旨

g. When the reading settles, record the output voltage again. Check that the two recorded readings differ no more than: ± 0.011Vdc (6010A) ± 0.0037Vdc (6011A) ± 0.007Vdc (6012B) ± 0.033Vdc (6015A) Source Effect (Line Regulation). Source effect is the change in dc output voltage resulting from a change in ac input voltage from the minimum to the maximum value as specified in Input Power Requirements in the Specifications Table, in the Operating Manual. Proceed as follows: a. Connect the test equ

ページ20に含まれる内容の要旨

d. Reduce the resistance of the load to draw an output current of: 17.0Adc (6010A) 120Adc (6011A) 17.5Adc (6012B) 5.0Adc (6015A) Check that the unit's CV LED remains lighted. e. Check that the rms noise voltage at the true rms voltmeter is no more than: 22mV rms (6010A) 8.0mV rms (6011A) 8.0mV rms (6012B) 50mV rms (6015A) Figure 2-4. RMS Measurement Test Setup, CV PARD Test Peak Measurement Procedure. Figure 2-5 shows the interconnections of equipment to measure PARD in Vpp. The equipme


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Agilent Technologies 6032A 取扱説明書 電源 16
2 Agilent Technologies 6012B 取扱説明書 電源 4
3 Agilent Technologies 6038A 6010A 取扱説明書 電源 3
4 Agilent Technologies 6023A, 6028A 取扱説明書 電源 5
5 Agilent Technologies 6035A 取扱説明書 電源 8
6 Agilent Technologies 6011A 取扱説明書 電源 1
7 Agilent Technologies 6023A 取扱説明書 電源 0
8 Agilent Technologies 6611C 取扱説明書 電源 19
9 Agilent Technologies 6031A 取扱説明書 電源 1
10 Agilent Technologies 6625A 取扱説明書 電源 0
11 Agilent Technologies 6632B 取扱説明書 電源 22
12 Agilent Technologies 6634B 取扱説明書 電源 5
13 Agilent Technologies 6629A 取扱説明書 電源 0
14 Agilent Technologies 6614C 取扱説明書 電源 7
15 Agilent Technologies 6628A 取扱説明書 電源 1
16 Sony AC U50A 取扱説明書 電源 5
17 Sony AC LS1 取扱説明書 電源 2
18 Sony NP-FM30 取扱説明書 電源 35
19 Sony NP FX101 取扱説明書 電源 1
20 Sony NH-AAA-DA 取扱説明書 電源 2