Furuno M51Aの取扱説明書

デバイスFuruno M51Aの取扱説明書

デバイス: Furuno M51A
カテゴリ: 電源
メーカー: Furuno
サイズ: 0.41 MB
追加した日付: 8/10/2013
ページ数: 22
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスFuruno M51Aの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Furuno M51Aに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Furuno M51Aをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Furuno M51Aのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Furuno M51Aの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Furuno M51A 取扱説明書 - Online PDF
Advertisement
« Page 1 of 22 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Furuno M51Aを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Furuno M51Aの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨






DLM 600W Series
Power Supplies
M51A Option: Isolated Analog
Programming Manual


Power Supplies

Elgar Electronics Corporation
9250 Brown Deer Road
San Diego, CA 92121-2294
1-800-73ELGAR (1-800-733-5427)
Tel: (858) 450-0085
Fax: (858) 458-0267
Email: sales@elgar.com
www.elgar.com
©2002 by Elgar Electronics Corporation
This document contains information proprietary to Elgar Electronics Corporation. The information contained herein is
not to be duplicated or transfer

ページ2に含まれる内容の要旨

.

ページ3に含まれる内容の要旨

SAFETY NOTICE Before applying power to the system, verify that the instrument is configured properly for the user’s particular application. WARNING! Hazardous voltages may be present when covers are removed. Qualified personnel must use extreme caution when servicing this equipment. Circuit boards, test points, and output voltages also may be floating with respect to chassis ground. Installation and servicing must be performed by qualified personnel who are aware of dealing pr

ページ4に含まれる内容の要旨

SAFETY SYMBOLS ii

ページ5に含まれる内容の要旨

ELGAR FIVE–YEAR WARRANTY Elgar Electronics Corporation (hereinafter referred to as Elgar) warrants its products to be free from defects in material and workmanship. This warranty is effective for one year from the date of shipment of the product to the original purchaser. Liability of Elgar under this warranty shall exist provided that: • the Buyer exposes the product to normal use and service and provides normal maintenance on the product; • Elgar is promptly notified of defects by the

ページ6に含まれる内容の要旨

This page intentionally left blank. iv

ページ7に含まれる内容の要旨

CONTENTS SECTION 1 M51A OPTION OVERVIEW 1.1 Introduction...................................................................................................... 1-1 1.2 General Description......................................................................................... 1-1 1.3 Specifications................................................................................................... 1-2 1.3.1 Electrical Specifications.........................................................

ページ8に含まれる内容の要旨

Contents DLM 600W Series LIST OF TABLES Table 2–1. INTFC SETUP Switch............................................................................... 2-1 Table 2–2. ISOLATED ANALOG INTERFACE Connector Pinout .............................. 2-4 Table 2–3. Remote Programming Configuration Options ........................................... 2-7 Table 2–4. Remote Monitoring................................................................................. 2-11 Table 2–5. Remote Digital Sta

ページ9に含まれる内容の要旨

SECTION 1 M51A OPTION OVERVIEW 1.1 Introduction This addendum is to be used in conjunction with the DLM 600W Series Power Supplies Operation Manual, Sorensen Document No. M362161-01. The Sorensen M51A Option for the DLM 600W Series power supplies provides a remote analog interface, which has safety isolation from the output terminals. This allows the remote analog interface to be connected to user accessible (SELV) control circuits, even though the output terminals were floated at a

ページ10に含まれる内容の要旨

M51A Option Overview DLM 600W Series 1.3 Specifications 1.3.1 Electrical Specifications Remote Voltage Programming Accuracy, 0-5/10V Inputs: Output Voltage: 0.5% of Vmax Output Current: 0.75% of Imax OVP: 1.0% of 1.1 X Vmax Remote 4-20mA Programming Accuracy: Output Voltage: 0.75% of Vmax Output Current: 1.0% of Imax 1.3.2 Supplemental Characteristics Remote Resistance Programming Accuracy, 0-5k Ω Input: Output Voltage: 1.0% of Vmax Output Current: 1.5% of Imax OV

ページ11に含まれる内容の要旨

SECTION 2 ISOLATED REMOTE ANALOG INTERFACE OPERATION 2.1 INTFC SETUP Switch The INTFC SETUP (Interface Setup) switch is accessible from the rear panel of the unit. It provides user selectability of the programming/monitoring ranges and signal types, as well as configuring the power supply for operation under remote control. Setting a switch to the UP position enables a function. The factory default settings are all switch positions OFF (down). See Figure 2–1 for a rear panel view

ページ12に含まれる内容の要旨

Isolated Remote Analog Interface Operation DLM 600W Series 2.1.1 INTFC SETUP Switch Functions The following sections describe the functions of the various switch positions: V, 10V or 4-20mA Select: Position-1, when ON, selects 0-10VDC programming of the output voltage. Also, must be set to ON position when the ISOLATED ANALOG INTERFACE connector is wired for 4-20mA output voltage programming. When OFF, selects 0-5VDC programming of the output voltage. I, 10V or 4-20mA Select: P

ページ13に含まれる内容の要旨

DLM 600W Series Isolated Remote Analog Interface Operation Figure 2–1. Rear Panel View, Low–Voltage Models Figure 2–2. Rear Panel View, High–Voltage Models M51A Option 2-3

ページ14に含まれる内容の要旨

Isolated Remote Analog Interface Operation DLM 600W Series 2.3 Isolated Analog Interface Connector The ISOLATED ANALOG INTERFACE connector is a 25-position female Subminiature-D type. Pin Function 1 ANALOG-CONTROL input 2 Return for 0-5/10V monitor outputs and EXTERNAL-OFF 3 OVP programming input 4 Voltage monitor output, 4-20mA 5 VOLTAGE-MODE status output 6 Return for 4-20mA monitor outputs, Auxiliary 5VDC, and digital I/O 7 Current monitor output, 0-5/10V 8 1.25VDC output for

ページ15に含まれる内容の要旨

DLM 600W Series Isolated Remote Analog Interface Operation 2.3.1 ISOLATED ANALOG INTERFACE Functions The following sections describe the functions of the various signals of the ISOLATED ANALOG INTERFACE. Pin numbers correspond to the connector pinout of Table 2–2. Digital Control Input Signals ANALOG-CONTROL: Pin-1, enables remote analog programming with an active-high logic level of 3-15VDC. An internal 100k Ω pull-down resistor is provided. When ANALOG- CONTROL is asserted, the

ページ16に含まれる内容の要旨

Isolated Remote Analog Interface Operation DLM 600W Series Analog Programming Signals OVP PROGRAMMING INPUT: Pin-3, an input signal of 0-5 volts or 0-10 volts (user selectable with INTFC SETUP switch) programs the OVP threshold from 5-110% of full scale output voltage. Signal is referenced to Pin-12. Circuit is SELV, and has electrical isolation from the output of the unit. VOLTAGE PROGRAMMING INPUT: Pin-9, an input signal for two methods of programming the output voltage: 0-5/10V v

ページ17に含まれる内容の要旨

DLM 600W Series Isolated Remote Analog Interface Operation CURRENT RESISTANCE PROGRAMMING OUTPUT: Pin-22 provides a 1mA current source which would be connected to Pin-10, CURRENT PROGRAMMING INPUT, with a 0-5k Ω external resistor connected between Pin-22 to Pin-12, to program the output current from 0-100% of full scale output. The INTFC SETUP switch Position-2, I, must be set to OFF (down) to select 0-5VDC input range. Circuit is SELV, and has electrical isolation from the output of the

ページ18に含まれる内容の要旨

Isolated Remote Analog Interface Operation DLM 600W Series 2.4.1 Voltage Source Programming of Output Voltage Setting up for voltage source programming of the output voltage is as follows: 1. Set Position-1, V, of the INTFC SETUP switch to OFF (down) for 0-5VDC programming range. 2. Set Position-1, V, of the INTFC SETUP switch ON (up) for 0-10VDC programming range. 3. Connect the external programming voltage source to the ISOLATED ANALOG INTERFACE connector, with positive to Pin

ページ19に含まれる内容の要旨

DLM 600W Series Isolated Remote Analog Interface Operation 4. Program the other parameters to the desired limit values: VOLTAGE PROGRAMMING INPUT, Pin-9, and the CURRENT PROGRAMMING INPUT, Pin-10, with respect to Pin-12. 5. Connect Pin-1, ANALOG-CONTROL, of the ISOLATED ANALOG INTERFACE connector to Pin-15. 2.4.4 Resistance Programming of Output Voltage Setting up for resistance programming of the output voltage is as follows: 1. Set Position-1, V, of the INTFC SETUP switch to O

ページ20に含まれる内容の要旨

Isolated Remote Analog Interface Operation DLM 600W Series 2.4.6 Resistance Programming of OVP Setting up for resistance programming OVP is as follows: 1. Set Position-3, OVP, of the INTFC SETUP switch to OFF (down) for 0-5VDC programming range. 2. Connect the external programming resistance, 0-5k Ω, to the ISOLATED ANALOG INTERFACE connector, from Pin-16 to Pin-12. 3. Connect a jumper from Pin-16 to Pin-3. 4. Program the other parameters to the desired limit values: VOLTAGE


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Furuno M51A 取扱説明書 電源 2
2 Furuno RS-600-ASAA 取扱説明書 電源 5
3 Furuno RS-600-ASAA 取扱説明書 電源 8
4 Sony AC U50A 取扱説明書 電源 5
5 Sony AC LS1 取扱説明書 電源 2
6 Sony NP-FM30 取扱説明書 電源 35
7 Sony NP FX101 取扱説明書 電源 1
8 Sony NH-AAA-DA 取扱説明書 電源 2
9 3Com 3645A 取扱説明書 電源 0
10 3Com 3CNJPSE24 取扱説明書 電源 2
11 3Com COREBUILDER 5000 取扱説明書 電源 0
12 3Com 3646A 取扱説明書 電源 0
13 3Com External PoE Power System PSE2500-A3 取扱説明書 電源 1
14 Sony AC E45HG 取扱説明書 電源 10
15 3Com Powerware Uninterruptible Power System Prestige Series 取扱説明書 電源 7