ページ1に含まれる内容の要旨
User Manual
Network Manageable
S Type Power Conditioner
With Battery Backup
Model: S20BLK
ページ2に含まれる内容の要旨
Entire contents copyright© 2007 American Power Conversion Corporation. All rights reserved. Reproduction in whole or in part without permission is prohibited. APC, the APC logo, and TRADEMARK NAMES are trademarks of American Power Conversion Corporation. All other trademarks, product names, and corporate names are the property of their respective owners and are used for informational purposes only. This manual is subject to change without notice.
ページ3に含まれる内容の要旨
Safety Information 1. Read this manual - Read all of the safety and operating instructions before installing and operating this device. 2. Keep this manual - Retain this manual, and all of the safety information that came with this device. 3. Warnings - Comply with all warnings presented in this manual, as well as any warnings found on the device. 4. Follow Instructions - Follow all instructions that pertain to operating and using the this device. 5. Cleaning - Shut off and unplug this devic
ページ4に含まれる内容の要旨
Safety Information (Continued) 15. Power Lines - Do not locate outside antenna systems near overhead power lines, or other electric light or power circuits, or where they may fall on or otherwise come in contact with these power sources. If you allow the ladder being used, or the antenna itself to come into contact with these power sources it could be fatal. 16. Overloading - Do not overload the wall outlet where this device is con- nected, and do not overload this device. Ensure the to
ページ5に含まれる内容の要旨
Protect Your Investment Thank you for selecting APC's Model S20BLK Power Conditioner. At APC, we know you have made an intelligent choice sure to reward you for many years. To ensure you receive all the benefits and protection that accompany your purchase, please take a few minutes to fill out and mail the enclosed Warranty Registration Card, or complete the online form at www.apc.com. Note: Under California law, failure to register your purchase may not exclude you from provisions of the
ページ6に含まれる内容の要旨
Class B Labeling and Instruction Manual Requirements Devices subject to Certification must be labeled with a Federal Communica- tions Commission (FCC) Identifier. Devices subject to Verification or Certifica- tion must be labeled with the following compliance statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, includin
ページ7に含まれる内容の要旨
Table of Contents Page Safety Information i Protect Your Investment iii Chapter 1 - Introduction 1-1 Proven Expertise… Proven Reliability 1-1 Package Contents 1-2 Safety Precautions 1-2 Unit Power Capacity 1-2 Features 1-3 Communications and Management 1-3 Environmental Monitoring 1-4 Pure Sine Wave Battery Backup 1-4 Automatic Voltage Regulation 1-4 Surge Protection 1-4 Isolated Noise Filter Banks 1-5 Rack Mountable 1-5 Removable Support Feet 1-5 ON/OFF Sequencing 1-5 Outlet ON/OFF Bank Control
ページ8に含まれる内容の要旨
Page Connecting the Components 2-12 S20BLK Setup 2-13 Chapter 3 - Troubleshooting 3-1 Unit will not turn on. 3-2 Connected equipment reboots or turns off during or after the unit switches to battery power 3-2 REPLACE BATTERY LED is illuminated 3-3 Contact Information 3-3 Limited Warranty 3-4 Appendix A - Specifications A-1 Appendix B - Network Management Card B-1 vi
ページ9に含まれる内容の要旨
Chapter 1 Introduction Figure 1. S20BLK Power Conditioner with Battery Backup (Front View) Proven Expertise… Proven Reliability From corporate data centers to home offices, APC is regarded as a leading innovator, designer and manufacturer of high-quality power protection solutions. With its TM proven reputation for Legendary Reliability , leading companies depend on APC every day, 24 x 7 to protect and support many of the most critical networks in the world. Over the last 20 years, APC has b
ページ10に含まれる内容の要旨
Package Contents Your S20BLK Power Conditioner package should contain the following: Item Item Description Quantity 1. S20BLK Power Conditioner with Battery Backup (battery 1 ea. pack included) 2. Front Panel Display (bezel) 1 ea. 3. AC Input Power Cord 1 ea. 4. Coaxial Patch Cables 2 ea. 5. RS-232 Cable 1 ea. 6. USB Interface Cable 1 ea. 7. Telephone Patch Cable 1 ea. 8. Ethernet Patch Cable 1 ea. 9. Temperature Probe 1 ea. 10. PowerChute Personal Edition Software CD 1 ea. 11. Network Manage
ページ11に含まれる内容の要旨
Features The S20BLK Power Conditioner’s major features are described in the following paragraphs. Communications and Management A universal serial bus (USB) port, RS-232 port, and Network Management Card (embedded Web server) provide multiple methods for monitoring and managing the S20BLK, and the equipment connected to it. For example, unit installers can integrate the S20BLK into any home automation network, and “hung” devices can be rebooted from a remote location. The following subpar
ページ12に含まれる内容の要旨
Network Management Card An Ethernet port is located on the S20BLK rear panel, and enables the S20BLK’s embedded Network Management Card (NMC) to connect to any Ethernet network. The NMC (Web server) enables users to remotely monitor and manage the S20BLK from any Web browser. All 12 outlets can be simultaneously turned OFF or ON via the NMC, but not independently. This capability will be available December 2006 by downloading the latest firmware from the APC Web site: www.apc.com/support,
ページ13に含まれる内容の要旨
Isolated Noise Filter Banks The S20BLK isolated noise filer banks (INFB) eliminate electromagnetic and radio frequency interference (EMI and RFI) that, when severe enough, can negatively impact sound and video quality. Each filter bank is electrically isolated from the other filter banks to prevent noise generated by one component from polluting other connected components. APC's noise filtering helps enable your system to perform to its maximum capabilities. Rack-mountable The rack-mount h
ページ14に含まれる内容の要旨
6 7 1 2 3 4 5 12 10 8 14 9 13 11 Figure 2. Front Panel Controls and Indicators DELAYED 1 Status Indicator 1 When lit (blue), conditioned power is being supplied to equipment connected to the rear-panel outlets marked Switched Delayed 1. ON BATTERY Status Indicator 2 When lit (orange), the Power Conditioner is operating on power from the internal Battery Pack and is providing clean power to the connected equipment. The unit will go On Battery when the input utility voltage either drops below
ページ15に含まれる内容の要旨
Vacuum Fluorescent Display 4 The vacuum fluorescent display (VFD) conveys unit and power status information. It is also used to display information when changing unit settings. Note: The VFD and light emitting diodes (LEDs) can be dimmed or turned off independently of each other via the front control panel SETUP push button. 5 Up Arrow Push Button This button is used to increase or turn on parameters for various user-selectable settings such as: Audible Alarms, Sensitivity, Display Dimm
ページ16に含まれる内容の要旨
10 Down Arrow Push Button This pushbutton is used to change (decrease or turn off) parameters for various user-selectable settings such as: Audible Alarms, Sensitivity, Display Dimmer, LED Dimmer, Go To Bat If, Outlet 1 & 2 Delay (in seconds), Low Bat Warning, Bat Rep Date, and so on. On/Off Switch 11 This switch controls power to all of the 12 outlets located on the rear of the unit. APC recommends the unit be left ON at all times. Control power to your system components as you normally w
ページ17に含まれる内容の要旨
Rear Panel Controls and Connectors The rear panel connectors for the S20BLK Conditioner are shown in Figure 3. Each numbered callout corresponds to a numbered description in the list that follows Figure 3. 1 2 3 4 5 13 14 12 10 9 8 6 11 7 12 Figure 3. Rear Panel Connectors, Indicator, and Circuit Breaker Note: All outlets provide surge protection, voltage regulation, noise filtering and pure sine wave battery backup power. Outlet Banks ENVIRONMENTAL Port 1 8 EXTERNAL BATTERY Ethernet Port
ページ18に含まれる内容の要旨
Outlets - These include the two rows of six outlets (total of 12 outlets) on 1 the rear of the S Type Power Conditioner, shown in Figure 3. These outlets are arranged based on the type of filtering protection (DIGITAL, VIDEO, ANALOG), and isolated noise filter banks (INFBs) eliminate electromagnetic interference (EMI) and radio frequency interference (RFI) that can negatively affect sound and video quality. We recommend that you examine the types of outlets provided, review your equipment
ページ19に含まれる内容の要旨
CIRCUIT BREAKER – A press-to-reset circuit breaker is provided. 4 When it is “tripped” due to an electrical surge or overload, it pops out and shuts down output power to the outlets. To reset the Circuit Breaker, press it in. ! Caution: When resetting the Circuit Breaker, push the button in quickly, and release the button. Do not hold the Circuit Breaker button in. Failure to comply may result in equipment damage. SYSTEM GROUND Screw 5 The S20BLK allows the grounding wires from your equipm
ページ20に含まれる内容の要旨
RS-232 Port 10 The RS-232 serial port allows you to monitor and manage the S20BLK, and also provides the ability to integrate the S20BLK into your home automation network. Note: This port can only be functional when the USB cable is not connected to the S20BLK. Surge Protected Telephone Jacks (TEL/DVR/SAT/DSL) 11 The S20BLK has a telephone line splitter (2-line 4-wire with splitter) with surge protection for components connected via telephone line. Connect the supplied RJ11 telephone cab
