ページ1に含まれる内容の要旨
4.8 VOLT RECHARGEABLE
CORDLESS SCREWDRIVER
Model 95065
SET up AnD OpERATInG InSTRuCTIOnS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MAnuAL.
© ®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written
consent of Harbor Freight Tools. Diagrams within
ページ2に含まれる内容の要旨
and sparks. Provide barriers or shields SpECIFICATIOnS as needed. Batteries 4.8 V NiCd Battery Pack Charging Time No more than 10 hours Electrical Safety Charger Adapter Input: 120 VAC, 60 Hz Output: 6 VDC, 300 mA 1. Avoid body contact with grounded Speed 200 RPM surfaces such as pipes, radiators, Chuck Hex drive ranges, and refrigerators. There is an Features 6 – Driver bits included increased risk of electric shock if your body is grounded. Save This Manual 2. Do not expose power tools
ページ3に含まれる内容の要旨
6. When operating a power tool Tool use and Care outside, use an outdoor extension 1. use clamps (not included) or other cord marked “W-A” or “W”. These practical ways to secure and support extension cords are rated for outdoor the workpiece to a stable platform. use, and reduce the risk of electric Holding the work by hand or against shock. your body is unstable and may lead to loss of control. personal Safety 2. Do not force the tool. Use the correct 1. Stay alert. Watch what yo
ページ4に含まれる内容の要旨
5. Include vibration-free periods each day Service of work. 1. Tool service must be performed by 6. Grip tool as lightly as possible (while qualified repair personnel. Service still keeping safe control of it). Let the performed by unqualified personnel tool do the work. could result in a risk of injury. 7. To reduce vibration, maintain the tool 2. When servicing a tool, use only as explained in this manual. If any identical replacement parts. Follow abnormal vibration occurs, stop
ページ5に含まれる内容の要旨
6. Do not force the Cordless Grounded Tools: Screwdriver. This tool will do the work Tools with Three prong plugs better and safer at the capacity for which it was designed. 1. Tools marked with “Grounding Required” have a three wire cord 7. unplug the Charger Adapter and three prong grounding plug. The from the Cordless Screwdriver plug must be connected to a properly and the electrical outlet before grounded outlet. If the tool should use or before performing any electrically m
ページ6に含まれる内容の要旨
7. Make sure the extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect the extension cords from sharp objects, excessive heat, and damp or wet areas. Outlets for 2-prong plug RECOMMEnDED MInIMuM WIRE GAuGE FOR EXTEnSIOn CORDS* 2. Double insulated tools may be used in (120/240 VOLT) either of the 120 volt outlets shown in EXTEnSIOn CORD the preceding illustra
ページ7に含まれる内容の要旨
unp ACKInG When unpacking, make sure that all the parts are included. See Figure C below. Figure C Charger Adapter Screwdriver Bits Cordless Screwdriver If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Battery precautions 1. To avoid accidents, never use a different charger adapter with this tool. 2. Do not expose this product to rain or wet conditions. 3. To avoid damage of cable and plug, never pull the cable
ページ8に含まれる内容の要旨
CHARGInG THE BATTERy 1. Insert the Charger Adapter (24) cord plug into the unit connector as shown below. 2. Plug the Charger Adapter module into an electrical outlet. The red Charging Indicator on the Cordless Screwdriver will light. Charge the new battery for 10 hours. When the battery is fully charged all three LEDs will light up. Remove the Charger Adapter (24) from the electrical outlet. The red Charging indicator will turn off. See Figure D. Testing the Battery Charge Figure D Front O
ページ9に含まれる内容の要旨
TROuBLESHOOTInG problem possible Cause probable Solution Cordless Screwdriver does Battery Pack is not charged. Recharge Battery Pack. not operate when Trigger Switch is pressed. Battery Pack does not 1. No power to Charger 1. Check electrical outlet for recharge after connecting Adapter. power. Charger Adapter for hours. 2. Charger Adapter defective. 2. Replace Charger Adapter. 3. Battery Pack defective. 3. Replace Battery Pack. MAInTEnAnCE 1. When finished using the Screwdriver, place in it
ページ10に含まれる内容の要旨
pARTS LIST part Description Qty part Description Qty 1 Output Axis 1 13 Motor 1 2 Gasket 1 14 Trigger Switch 1 3 Gearbox 1 15 Housing (left / right) 1 4 Ring, Inner, Self-lock 1 16 LED Indicator 1 5 Core, Inner, Self-lock 1 17 Light Cover 1 6 Block, Self-lock 1 18 Light Bulb 1 7 Gear, Front Star 1 19 Switch, Light 1 8 Holder, Star Gear, Middle 1 20 Connector Pin 1 9 Gear, Star, Back 1 21 PDC 1 10 Gasket, Large 1 22 Battery Pack 1 11 Motor Holder 1 23 Charger Socket 1 12 Motor Gear 1 24 Charger A
ページ11に含まれる内容の要旨
LIMITED 90 DAy WARRAnTy Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installati
