ページ1に含まれる内容の要旨
Guidance for
AS/400 Print Solution
ページ2に含まれる内容の要旨
2 AS/400 Print Solution —
ページ3に含まれる内容の要旨
Software License Agreement INSTALLING OR OTHERWISE USING THIS SOFTWARE PRODUCT CONSTITUTES YOUR ACCEPTANCE OF THE FOLLOWING TERMS AND CONDITIONS (UNLESS A SEPARATE LICENSE IS PROVIDED BY THE SUPPLIER OF APPLICABLE SOFTWARE IN WHICH CASE SUCH SEPARATE LICENSE SHALL APPLY). IF YOU DO NOT ACCEPT THESE TERMS, YOU MAY NOT INSTALL OR USE THIS SOFTWARE, AND YOU MUST PROMPTLY RETURN THE SOFTWARE TO THE LOCATION WHERE YOU OBTAINED IT. THE SOFTWARE INSTALLED ON THIS PRODUCT INCLUDES NUMEROUS INDIVIDU
ページ4に含まれる内容の要旨
Limitation of Liability IN NO EVENT WILL TTEC OR ITS SUPPLIERS BE LIABLE TO YOU FOR ANY DAMAGES, WHETHER IN CONTRACT, TORT, OR OTHERWISE (EXCEPT PERSONAL INJURY OR DEATH RESULTING FROM NEGLIGENCE ON THE PART OF TTEC OR ITS SUPPLIERS), INCLUDING WITHOUT LIMITATION ANY LOST PROFITS, LOST DATA, LOST SAVINGS OR OTHER INCI- DENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABIL- ITY TO USE THE SOFTWARE, EVEN IF TTEC OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
ページ5に含まれる内容の要旨
Trademarks and Copyright Trademarks • Copyright permissions regarding screenshots, pictures and descriptions, included in this document, can be obtained from AXIS Communications AB. • AXIS Communications, AXIS 5570e, AXIS 5570e IPDS SNA and design (the AXIS logo) are either registered trademarks or trademarks of AXIS AB and AXIS Commu- nications AB in Sweden, the European Union, the United States, Japan and other countries. All "AXIS 5570e" described henceforth means "AXIS 5570e IPDS SNA". •
ページ6に含まれる内容の要旨
Disclaimer Notice The following notice sets out the exclusions and limitations of liability of TOSHIBA TEC CORPORATION (including its employees, agents and sub-contractors) to any pur- chaser or user (‘User’) of the e-STUDIO520/600/720/850, e-STUDIO281C/351C/451C, e-STUDIO352/452, e-STUDIO202L/232/282, e-STUDIO2500C/3500C/3510C, e-STUDIO165/205, e-STUDIO167/207/237, e-STUDIO523/603/723/853, e-STUDIO353/453, e-STUDIO203L/233/283, e-STUDIO2020C/2330C/2820C/2830C/ 3520C/3530C/4520C, e-STUDIO552
ページ7に含まれる内容の要旨
Preface The e-STUDIO520/600/720/850, e-STUDIO281C/351C/451C, e-STUDIO352/452, e-STUDIO202L/232/282, e-STUDIO2500C/3500C/3510C, e-STUDIO165/205, e-STUDIO167/207/237, e-STUDIO523/603/723/853, e-STUDIO353/453, e-STUDIO203L/233/283, e-STUDIO2020C/2330C/2820C/2830C/3520C/3530C/ 4520C, e-STUDIO5520C/6520C/6530C, e-STUDIO283C/353C/453C, e-STUDIO205L/ 255/305/355/455, e-STUDIO555/655/755/855 and e-STUDIO182/212/242 provides powerful network printing capability with many output finishing options. No
ページ8に含まれる内容の要旨
8 AS/400 Print Solution — Preface
ページ9に含まれる内容の要旨
Table of Contents Software License Agreement .........................................................................3 Trademarks and Copyright .............................................................................5 Disclaimer Notice............................................................................................6 Preface ...........................................................................................................7 About this guide................................
ページ10に含まれる内容の要旨
10 AS/400 Print Solution — Table of Contents
ページ11に含まれる内容の要旨
1. AXIS Network Print Server AS/400 Print Solution — 1. AXIS Network Print Server 11
ページ12に含まれる内容の要旨
Overview Components ® The components of the AS/400 Printing Solution are: • AS/400 server • Your equipment • USB cable to connect the AXIS 5570e Print Server and your equipment • AXIS 5570e Print Server • Client PC workstation • Custom Config file (Config_landscape) TOSHIBA TEC Products The configuration diagram illustrates the relationship among these components. USB Connection AXIS 5570e Network HUB Print Server AS/400 Server Client PC Client PC Client PC AS/400 Printing Solution components P
ページ13に含まれる内容の要旨
Finishing options and logical printers TOSHIBA offers several finishing options in addition to standard print commands com- ing from the AS/400. For example, stapling and hole punching are finishing options. The finishing options are grouped in several preconfigured sets, which you associate with up to eight logical printers. NOTE: • Any finisher options are not supported in e-STUDIO165/205 and e-STUDIO167/ 207/237. AS/400 Print Solution — Overview 13
ページ14に含まれる内容の要旨
Installation Installation procedure Install the AS/400 printing solution in two steps: 1. Set up the hardware 2. Set up the AS/400 printer Step 1: Set up the hardware NOTE: • The controller can be directly connected to the AS/400 network at the same time. Thus, PCL-based or raw print jobs can be sent to it via the network, bypassing the AXIS 5570e Print Server device. 1. Following the product installation instructions that came with the AXIS 5570e Print Server, setup this device. 2. Connec
ページ15に含まれる内容の要旨
Step 2: Set up the AS/400 printer On the AS/400, use the CRTDEVPRT command to configure the print settings accord- ing to the following table: AS/400 Print settings Setting Name Value Device description Unique description, such as TOSHIBA Device class *LAN Device type *IPDS Device model 0 LAN attachment *IP Port number e.g. 5001 Font identifier 11 Remote location IP address of AXIS 5570e All other settings can be left unchanged. NOTE: • If you experience any problems, press F1 for help.
ページ16に含まれる内容の要旨
NOTE: • To protect the admin pages and the Configuration Wizard from unauthorized use, enter a password (by default set to pass) in the Root Password field under Admin General Settings. • Use the same port number when creating the print device (page 15). Note for IPDS printing: In the Configuration Wizard, you can choose between PCL or PostScript printing. Choose PCL for Printer Driver. PostScript is not available. 2. Click the Configuration Wizard for IBM sessions button. 3. Delete the pr
ページ17に含まれる内容の要旨
Configuration Available AXIS firmware version Use the production release version or service release version given in the following table when using TOSHIBA MFP. All official firmware releases for the AXIS 5570e are available on AXIS website. TOSHIBA MFP Production release Service release version version e-STUDIO520/600/720/850 7.08 or later 7.06.04 or later e-STUDIO523/603/723/853 e-STUDIO281C/351C/451C e-STUDIO352/452 7.08 or later 7.08.2 or later e-STUDIO353/453 e-STUDIO202L/232/282 e-STUDIO2
ページ18に含まれる内容の要旨
8. The print server will restart in five seconds running the new software. Update procedure of the config file: 1. Get the config file by FTP. Open a Windows command prompt and enter the following: ftp default user name root default password pass get config bye 2. Update the custom driver parameters from the config file; the parameters needed for the custom driver begin with DC Gen- eral Menu and end with DC PCL Copies. 3. Save the file as, e.g. my_template. 4. Upload 'my_templ
ページ19に含まれる内容の要旨
Copier model When printing portrait data, select an appropriate copier model, e.g. Toshiba eSTUDIO520/600/720/850 or Toshiba eSTUDIO281C/351C/451C. When printing landscape data, select Custom copier driver for Copier model. P.31 "Custom copier driver" NOTE: • In using e-STUDIO167/207/237, choose e-STUDIO165/205. • In using e-STUDIO523/603/723/853, choose e-STUDIO520/600/720/850. • In using e-STUDIO353/453, choose e-STUDIO352/452. • In using e-STUDIO2020C/2330C/2820C/2830C/3520C/3530C/4520C, c
ページ20に含まれる内容の要旨
Only PCL available In the Configuration Wizard for IBM sessions, select PCL for Printer Driver. PostScript is not available. Edit Session: Only PCL is available for IPDS Printer Driver under Edit Session. PostScript is not available. 20 AS/400 Print Solution — Configuration
