ページ1に含まれる内容の要旨
Stacker 1000
Operator Manual
701P98048
ページ2に含まれる内容の要旨
Welcome! Congratulations on acquiring the
Stacker 1000. Team
looks forward to supporting you and helping you increase Printer Serial Number: _________________________________ your organizational productivity. The integrated features, ease of operation, and reliability of the
Stacker 1000 allows you In order to locate the Printer Serial Number, refer to the printer to concentrate on your business and leave the printing and operator manual. finishing to the
ページ3に含まれる内容の要旨
Table of contents Printer media information.......................................... 9 Safety notes ....................................................... 1 Stacker capacity.........................................................9 Stacker overview ............................................... 3 Electrical requirements.............................................. 9 Introduction ............................................................... 3 Power consumption ..............................
ページ4に含まれる内容の要旨
ii Stacker 1000 Operator Manual Table of contents
ページ5に含まれる内容の要旨
Safety notes The
Stacker 1000 is designed and tested to meet strict This product is equipped with a three-wire, grounding-type safety requirements. These requirements include safety plug (in other words, a plug which has a third grounding pin). agency examination and approval and compliance to any This product also is equipped with an additional safety device. established environmental standards. Please read the following The plug fits into a grounding-type power outlet only. This is a
ページ6に含まれる内容の要旨
2 Do not install the stacker where the floor or base is unstable. Unplug this stacker from the wall outlet and refer the servicing The stacker may fall, causing personal injury and/or serious of it to qualified service personnel under the following damage to the stacker. conditions: Never spill liquid of any kind on the stacker. • when the power cord is damaged or frayed; • if liquid is spilled into the product; Do not allow anything to rest on the power cord. Do not locate • if the stacker is
ページ7に含まれる内容の要旨
Stacker overview Introduction Identifying the stacker parts The Stacker 1000 is an optional finishing device which may be Tray used with the
8830 printer, the
8830 Digital extensions Document System (DDS), or the
Productivity Centre (for longer- 8233. The illustration below shows the Stacker 1000 with a size prints)
8830 printer. The Stacker 1000 stacks a maximum of 1000 prints of various sizes. Print sizes include A (A4) through E (A0). Depending on the print size, pr
ページ8に含まれる内容の要旨
4 7UD\H[WHQVLRQV Stacker operation The Stacker 1000 is equipped with tray extensions: 6ZLWFKLQJRQWKHVWDFNHU Tray The stacker is “switched on” by connecting the power cord to extensions the power outlet. There is no power switch. The power cord is the on/off switch. Once the power cord is connected to the power outlet, the stacker motor drive and fan initialize. 1RUPDORSHUDWLRQ As media leaves the printer, the lead edge of the media enters the stacker. A motion sensor in the stacker detect
ページ9に含まれる内容の要旨
0HGLDVWRUDJHFRPSDUWPHQWV 3ULQWVL]HLQIRUPDWLRQ As stated before, the Stacker 1000 is equipped with two storage As stated before, the Stacker 1000 stacks a maximum of 1000 compartments. They are located on each side of the stacker. prints; these prints may be of various media sizes. Depending on the print size, the stacker can hold the following quantities: • D-size (A1) landscape prints: 750 maximum • E-size (A0) portrait prints: 375 maximum The stacker can actually hold a larger number o
ページ10に含まれる内容の要旨
6 Problem solving &OHDULQJPHGLDMDPV Jam clearance Use the following procedure in order to clear a media jam from The stacker does not detect error conditions such as media the stacker: jams. If a media jam occurs, the motor drive and blower switches off, and the stacker no longer accepts media. This is 1. Move the stacker by pulling the entire stacker outward and the only indication that the stacker is no longer functioning. away from the printer. Media jams may occur as the media is exiting
ページ11に含まれる内容の要旨
Moving the stacker Problem solving Whenever you are required to move the stacker away from the printer, perform the following steps: Problem Action 1. Move the stacker by pulling the entire stacker outward and The stacker is not functioning. Ensure that the power cord is away from the printer. connected to the power outlet. 2. Reposition the stacker against the printer and ensure that Disconnect and reconnect the the stacker is positioned correctly: cord to the outlet. If the problem conti
ページ12に含まれる内容の要旨
8 Technical data Stacker relocation Technical data The stacker must be moved by authorized personnel only. 6SDFHUHTXLUHPHQWV In order to ensure that the stacker operates reliably after moving it to a new location, consider the following guidelines: • The new location must provide minimum clearances around the stacker. These clearances are shown in the diagram which is located in the Technical data section of this manual. • The flooring must be capable of supporting at least 100 lb. (45.5 kg) f
ページ13に含まれる内容の要旨
'LPHQVLRQV 6WDFNHUFDSDFLW\ :HLJKW 100 lbs. (45.5 kg) Maximum of 1000 prints of various sizes Maximum of 750 D-size (A1) prints +HLJKW 37.9 inches (963 mm) Maximum of 375 E-size (A0) prints :LGWK 52.8 inches (1341 mm) (OHFWULFDOUHTXLUHPHQWV 'HSWK 44.6 inches (1133 mm) 9ROWDJH 85-264 VAC 3ULQWHUPHGLDLQIRUPDWLRQ )UHTXHQF\ 47-440 Hz 6WDQGE\&XUUHQW 0 Amps 0HGLDW\SH 5XQQLQJ&XUUHQW 0.8 Amps (115 VAC) for USA and Canada 0.5 Amps (250 VAC) for EO • Bond (20 lb.) The stacker is designed to
ページ14に含まれる内容の要旨
10 3RZHUFRQVXPSWLRQ )HDWXUHV 6WDQGE\ Less than 50 watts • Two media storage compartments 5XQQLQJ 50 watts (0.80A rms at 115 VAC; 0.50A rms at • Automatic shutoff 230 VAC) • Tray extensions 7HPSHUDWXUH • Automatic media detection 0LQLPXP 60 F (15 C) 0D[LPXP 80 F (27 C Stacker serial number location +XPLGLW\ 20% to 80% Relative Humidity In order to locate the serial number of your stacker, you must (OHYDWLRQ Maximum of 7000 feet (2133 m) above seal level first move the stacker away from
ページ15に含まれる内容の要旨
If necessary, the user should consult the dealer or an It’s illegal experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the Federal Communications Commission ,QWKH86$ helpful: It is against U.S. law to copy any material which is How to Identify and resolve Radio-TV Interference copyrighted without the permission of the copyright owner. Problems However, if the copying falls within the “Fair Use” library Stock Number: 004-000
ページ16に含まれる内容の要旨
Prepared by: Multinational Customer and Service Education 780 Salt Road Webster, New York 14580 Copyright© 1998 by Xerox Corporation. Allrights reserved. XEROX and all product names and number names are trademarks of XEROX CORPORATION. Other company trademarks are also acknowledged. Printed in U.S.A. 701P98048 3/98
