ページ1に含まれる内容の要旨
Dear Sceptre Customer,
Congratulations on your new SCEPTRE E47 HDTV purchase. Thank you for
your support. To ensure safety and many years of trouble free operation of
your TV, please read the manual carefully before making any adjustments,
and keep them in a safe place for future references. We hope you enjoy your
new SCEPTRE HDTV.
For technical assistance, please call 1800-788-2878 and select option 3 or
email our tech support group at sceptrets@sceptre.com
ページ2に含まれる内容の要旨
IMPORTANT INFORMATION WARNING: The appliance coupler is used as disconnect device, the disconnect device shall remain readily WARNING: The battery shall not be exposed to excessive heat such as sunshine, fire or the like. - 2 - www.SCEPTRE.com SCEPTRE E47 HDTV User Manual
ページ3に含まれる内容の要旨
SAFETY INSTRUCTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and / or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning t
ページ4に含まれる内容の要旨
SAFETY INSTRUCTIONS This product is designed and manufactured to operate within defined design limits, and misuse may result in electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of the product. Read the following safety instructions before operating the display. Keep these instructions in a safe place for future reference. To avoid
ページ5に含まれる内容の要旨
The wall socket should be installed product may cause fire or electric near the equipment and should be shock. easily accessible. Do not install the product in an area Only the marked power source can be with heavy dust or high humidity. used for the product. Any power Operating the product in environments source other than the specified one with heavy dust or high humidity may may cause fire or electric shock. cause fire or electric shock. Do not touch the power cord during Ho
ページ6に含まれる内容の要旨
IMPORTANT INFORMATION Television Antenna Connection Protection External Television Antenna Grounding If an outside antenna or cable system is to be connected to the TV, make sure that the antenna or cable system is electrically grounded to provide some protection against voltage surges and static charges. Article 810 of the National Electrical Code, ANSI/NFPSA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wi
ページ7に含まれる内容の要旨
Opening the Package The SCEPTRE TV is packaged in a carton. Any standard accessories are packed separately in another carton. The weight of the TV is approximately 42 lbs. Due to the size and weight of the product, it is suggested that it must be handled by a minimum of 2 or more persons. Since the glass can be easily scratched or broken, please handle the product gently. Never place the unit on a surface with the glass facing downwards unless it is on protective padding. When openin
ページ8に含まれる内容の要旨
Attaching or Removing the Stand 1. To attach the stand place the display unit flat on a table. Afterwards attach the base onto the display and screw in the 5 screws to secure the stand. The longer side of the stand faces the front. 2. To remove the stand, remove the 4 screws indicated in the picture and the stand will come off. - 8 - www.SCEPTRE.com SCEPTRE E47 HDTV User Manual
ページ9に含まれる内容の要旨
Table of Contents IMPORTANT INFORMATION .............................................................................................................. 2 SAFETY INSTRUCTIONS .................................................................................................................... 3 SAFETY INSTRUCTIONS .................................................................................................................... 4 IMPORTANT INFORMATION .....................................
ページ10に含まれる内容の要旨
Identifying Front and Rear Panel Front View INDICATOR LIGHT – The light is red when power is plugged in but the TV is not turned on. The light turns blue when the TV is turned on. Because of the LCD in the panel, the TV might take 10 – 12 seconds to power on. REMOTE SENSOR – The remote sensor receives all the commands from the remote control. Rear View Mounting Pattern Mounting Specification: 400mm x 400mm using screw size M6. L
ページ11に含まれる内容の要旨
Side Control Buttons 1. VOL(-) – This button decreases the TV’s volume. If a sub-menu is active, pressing this button will move the select left. 2. VOL(+) – This button increases the TV’s volume. If a sub-menu is active, pressing this button will move the selection right. 3. CH(▼) – This button changes the TV channel down. If the OSD is active, this button functions as down for the menu. 4. CH(▲) – This button changes the TV channel up. I
ページ12に含まれる内容の要旨
Rear View Connections 1. SPDIF - This connection port is used for sending out digital audio signals to digital surround sound receivers. The orange (COAX SPDIF OUT) connector sends out either bit-stream or PCM digital sound signal to a home theater receiver with digital coax input. 2. TV – This connection is for digital or analog cable without the cable box or over-the-airwave antennas. The tuner is a hybrid tuner that tunes to both
ページ13に含まれる内容の要旨
purchase a MHL cable from any electronic store and connect it to HDMI3 and also your cell phone. Make sure the TV’s source is changed to HDMI 3 and turn on your cell phone. You should see an image of your cell phone screen. 6. USB – USB connects to USB flash drives for playing music and picture. The USB port is also used for updating the TV’s firmware. 7. Analog Audio Out – This connection is for connecting to analog audio receivers. 8. Video – Video connects to devices that use compo
ページ14に含まれる内容の要旨
SCEPTRE Remote Control This remote control follows SONY’s universal remote code. To find the actual code you need to consult your cable or satellite tech support. - 14 - www.SCEPTRE.com SCEPTRE E47 HDTV User Manual
ページ15に含まれる内容の要旨
For universal remotes, this TV follows SONY’s universal remote code. You need to find the actual code from your cable or satellite or universal remote provider. 1. POWER – Turns the TV on or off. 2. INFO – Shows the display info. 3. FREEZE – Press this button to freeze current picture. 4. SLEEP – Turns the TV off in a specific set of time dependent on your selection. 5. CC – Cycles between different closed captioning modes. 6. MTS – Selects stereo, mono, or second audio programming. 7.
ページ16に含まれる内容の要旨
Installing Batteries to the Remote Control Please insert two AAA batteries into the remote control. Make sure that you match the (+) and (-) symbols on the batteries with the (+) and (-) symbols inside the battery compartment. Afterwards, re-attach the battery cover. Please note: Only use AAA batteries. Do not mix new and old batteries. This may result in cracking or leakage that may pose a fire risk or lead to personal injury.
ページ17に含まれる内容の要旨
Connection Suggestions If You Have Digital Cable without Cable Box or Antenna… 1. Make sure the power of HDTV is turned off. 2. Connect the Coaxial RF cable from your antenna or digital cable to the TV port on the back of your HDTV. 3. Turn on the HDTV. 4. Follow the first time on screen instructions. Please Note : Not all broadcasts are in High Definition (HD). Please refer to your local broadcasting stations for more information.
ページ18に含まれる内容の要旨
Connecting DVD Player with Component YPbPr… 1. Make sure the power of HDTV and your DVD player is turned off. 2. Obtain a Component Cable. Connect the green color connector to both your DVD player and YPbPr’s green connector port on the back of your HDTV. 3. Connect the blue color connector to both your DVD player and YPbPr’s blue connector port on the back of your HDTV. 4. Connect the red color connector to both your DVD player and YPbP
ページ19に含まれる内容の要旨
Connecting Wii™ with Composite… 1. Make sure the power of HDTV and your Wii™ is turned off. 2. Obtain a Yellow Video Cable. Connect the Yellow Video connector to both your Wii™ and AV’s Yellow Video connector port on the back side of your HDTV. 3. Obtain a RCA Audio Cable. Connect the white color connector to both your Wii™ and AV’s white connector port on the back side of your HDTV. 4. Connect the red color connector to both your Wii™
ページ20に含まれる内容の要旨
Connecting Cable or Satellite boxes with HDMI… 1. Make sure the power of HDTV and your set-top box is turned off. 2. Connect a HDMI cable to the HDMI output of your set-top box and the other end to the HDMI port on the back of your HDTV. 3. Turn on the HDTV and your set-top box. 4. Use the remote control’s source button or the source button on the TV to switch to HDMI. Please Note : Please reference the set-top box’s manual
