ページ1に含まれる内容の要旨
MP7760 Multimedia Projector
Operator’s Guide
MP7630 Projecteur multimédia Guide de l'opérateur
MP7630 Multimedia-Projektor Benutzerhandbuch
Proyector de Multimedia MP7630 Manual del Usuario
MP7630 Proiettore Multimediale Manuale dell'operatore
MP7630 Bruksanvisning för multimediaprojektor
MP7630 Multimedia Projector Gebruiksaanwijzing
™
© 3M IPC 2000 3M Multimedia Projector MP7760
1
ページ2に含まれる内容の要旨
™ 3M Multimedia Projector MP7760 © 3M IPC 2000 2
ページ3に含まれる内容の要旨
Table of Contents Please click on any section to jump to that section Introduction Safeguards .................................................................................... 4 Warranty ........................................................................................ 6 Section 1: Unpack 1-1. Contents of Shipping Box ...................................................... 7 1-2. Keep Your Packing Materials ................................................. 7 1-3. What’s Next?............
ページ4に含まれる内容の要旨
Introduction Intended Use Before operating the machine, please read the entire manual thoroughly. The 3M Multimedia Projector MP7760 was designed, built, and tested for use indoors, using 3M lamps and nominal local voltages. The use of other replacement lamps, outdoor operation, operation in environments containing heavy cigarette smoke or different voltages has not been tested and could damage the projector or peripheral equipment and/or create potentially unsafe operationg conditions. Importan
ページ5に含まれる内容の要旨
Introduction Product Safety Labels Safety labels are used on or within the 7760 projector to alert you to items or areas requiring your attention. Inside of projector gets very HOT! Allow internal parts to cool before replacing the lamp. Location of Product Safety Labels Save These Instructions The information contained in this manual will help you operate and maintain your 3M™ MP7760 Multimedia Projector. ™ © 3M IPC 2000 3M Multimedia Projector MP7760 5
ページ6に含まれる内容の要旨
Introduction Thank you for choosing 3M Thank you for choosing 3M multimedia projection equipment. This product has been produced in accordance with 3M’s highest quality and safety standards to ensure smooth and troublefree use in the years to come. For optimum performance, please follow the operating instructions carefully. We hope you will enjoy using this high performance product in your meetings, presentations, and training sessions. Warranty Limited Warranty 3M warrants this product against
ページ7に含まれる内容の要旨
Section 1: Unpack 1-1. Contents of Shipping Box The MP7760 is shipped with the necessary cables required for standard VCR, PC or laptop computer connec- tions. Carefully unpack and verify that you have all of the items shown below in Figure 1-1. If any of these items are missing, please contact your place of purchase. Item Quantity Item Quantity 1. MP7760 Multimedia Projector 1 7. Audio cable RCA to 3.5 mm stereo 1 2. IR Remote Control transmitter 1 8. Serial-Mouse cable 1 (Two AAAbatteries inc
ページ8に含まれる内容の要旨
Section 2: Production Description 2-1. Machine Characteristics The MP7760 integrates NTP lamp and Digital Light Processor (DLP) technology. It accepts input from computer and/or video sources and projects a super bright image. The MP7760 Multimedia Projector is easy to set up and use. It offers the following features: * Extremely light weight and portable * NTP projection lamp 200W * VGA (640 x 480) expansion * SVGA (800 x 600) expansion * XGA (1024 x 768) native resolution * SXGA (1280 x 1024)
ページ9に含まれる内容の要旨
Section 3: Set-Up/Connections 3-1. Terminal Connection Panel The MP7760 projector has terminal connections on the backside of the projector. Refer to Section 3.4-Cable Connections for more detail. Figure 3-1. Input Connection Terminals Figure 3-1. Input Connection Terminals 1. SVHS: S-VHS video input. 2. VIDEO IN: Composite video input. 3. AUDIO IN: Audio input (Stereo converted to mono). 4. AUX IN: Auxilary/Camera input. Only compatible with 3M devices. 5. PC/RGB IN: RGB video input from comput
ページ10に含まれる内容の要旨
Section 3: Set-Up/Connections 3-3. Mouse Connection The MP7760 has mouse emulation capability. Connect your computer mouse to the MP7760 and control computer mouse functions using the remote control. 1. Power down the computer and projector. 2. Remove the mouse cable connection from your computer mouse port. 3. Connect the 9-pin D-Sub plug on the mouse cable to the RS-232 port on the projector. (Not necessary for USB mouse emulation!) 4. RS-232 Serial Mouse: Connect 9-pin D-Sub plug on mouse ca
ページ11に含まれる内容の要旨
Section 3: Set-Up/Connections Cable Connection, continued *PC-Audio cable optional ***USB Mouse cable optional **MAC cable and adapter optional Figure 3-3. Cable Connections ™ © 3M IPC 2000 3M Multimedia Projector MP7760 11
ページ12に含まれる内容の要旨
Section 3: Set-Up/Connections 3-5. Image Size (Projector-to-Screen Distance) Adjust the size of the projected image by using the zoom ring on the upper side of the projection lens. Figure 3-4. The projected image size values, as they relate to the distance-to-screen value, are shown for focal lengths of f=28mm and f=36.2mm. Figure 3-5. . Figure 3-4. Adjusting Focus and Zoom Maximum (f = 28 mm) Minimum (f = 36.2 mm) Distance to Screen Image Width Image Height Image Width Image Height m (ft.) m (i
ページ13に含まれる内容の要旨
Section 4: Operating Instructions 4-1. Power Up Projector Read the Important Safeguards before operating the MP7760 projector. After all cable connections have been completed, the projector can be powered up. During operation, keep the exhaust and intake air vents clear of obstructions to allow proper cooling. Allow a projector that has been stored in a cold place to warm up to room temperature Caution before applying power. Figure 4-1. Power Up Projector 2 1. Press the Main Power switch ˚ to ON
ページ14に含まれる内容の要旨
Section 4: Operating Instructions 4-2. Standby Mode When the projector is not being used, place it into standby mode. 1. Press the Standby button. 2. The lamp will switch off and the red LED will illuminate. üüüüü Note: The fan motor will continue to run for a few minutes until the projector cools down and then the fan will turn off. 3. Press the Standby button again to illuminate the lamp and project an image on the screen. 4-3. Projector Power Down 1. Press the Standby button to place the proj
ページ15に含まれる内容の要旨
Section 4: Operating Instructions Sub-Menu: Select the desired sub-menu (see Main Menu). Press the Disc Pad or Joystick to the right or the Enter button to display the sub-menu. The sub-menu name is on the top line. A check box field at the right of a sub-menu line indicates that you can toggle that value On/Off by pressing the Enter button. A slider bar at the right of a sub-menu line indicates you can increase or decrease the value. A number field at the right of a sub-menu line
ページ16に含まれる内容の要旨
Section 4: Operating Instructions 4-5. Menu Adjustments/Settings, continued In active Video mode Picture (Video) Description / Action Default Setting Sub-Menu Items Bs rightnessAdjustthebrightnes CtontrastAdjustthecontras Cn olorAdjustcolorsaturatio TC intAdjustHUEforNTS Tools Description/ActionDefaultSetting Sub-MenuItems VeolumeAdjustvolum Af udioAnudiomute-on/-of-o Ff reezeFfreezeframe-on/-of-of Ti ff Mf agnifyMfagnifymode-on/-of-of FractorAdjustmagnificationfacto Selecttim
ページ17に含まれる内容の要旨
Section 4: Operating Instructions 4-5. Menu Adjustments/Settings, continued In active PC/RGB mode Advanced Set-Up (PC/RGB) Description / Action Default Setting Sub-Menu Items Select projection orientation Projection (Standard / Rear / Rear/Top Down / Standard (drop-down window) Top/Down) Remote control receiver Remote Control -on -on / -off Select remote control address RC Address 1 (1 / 2 / 3 / 4) Select Sync Mode for PC/RGB Sync Mode (separate TTL / composite TTL / separate TTL (drop-down
ページ18に含まれる内容の要旨
Section 4: Operating Instructions 4-5. Menu Adjustments/Settings, continued Color Manager Description / Action Default Setting Sub-Menu Items Bn rightness redAdjustbrightnessforredportio CnontrastredAdjustcontrastforredportio Bn rightnessblueAdjustbrightnessforblueportio CnontrastblueAdjustcontrastforblueportio Ds efaultSetscolorsettingstodefaultvalue Test Description/ActionDefaultSetting Sub-MenuItems Parameterdisplaywindow ParameterDisplay -off -on/-o
ページ19に含まれる内容の要旨
Section 5: Remote Control 5-1. Remote Control Functions Aim the remote control toward the projection screen or at the sensor. Press desired remote button to send a signal to the projector. *Standby: Mute: Switch the projector between Toggle On/Off the audio sound. Standby mode (lamp off, fan off) PC: and Operation mode (lamp on, fan Switch displayed image to PC/RGB input. on). *Volume: Decrease (-) or increase (+) Brightness: Decrease (-) or speaker volume. increase (+) brightness of the Video:
ページ20に含まれる内容の要旨
Section 5: Remote Control 5-2. Meaning Of The Icons An icon will display to indicate a presentation tool is active. Pointer mode Activate with Pointer key on IR-Remote control In the Pointer mode you can move a pointer over and around the picture area. By pressing the Pointer key on the remote control a second time it will be turned off. Freeze mode Activate with Freeze key on IR-Remote control In the Freeze mode the picture will be frozen. Pressing the Freeze key on the remote control a second
