ページ1に含まれる内容の要旨
Quick Reference Guide
Setup ....................................... 1
Connections ............................. 1
Projection preparation and
adjustments .............................. 3
Turning the projector off ............ 6
Functions for Enhancing
Projection ............................... 7
List of configuration setting
menus .....................................11
Troubleshooting ...................... 12
Replacing the Lamp ................15
List of Supported Monitor
Displays ............
ページ2に含まれる内容の要旨
Set up the projector so that the distance from the screen to the projector's lens is 77–1113 cm. Setup User's Guide The shorter the distance between the two, the smaller will be the images, and the greater the "Screen Size and distance, the larger will be the images. Adjust the distance in accordance with the size of the Projection Distance" screen. If using an optional lens, refer to the documentation for the lens. Be sure to turn the power for all components off before User's Guide "Conn
ページ3に含まれる内容の要旨
Connecting to video equipment To audio RCA audio cable (accessory) output port The [Audio] port to use is the port that is in the same box as the port being used to input the video signals. Audio cable (accessory) Adapters RCA audio cable (commercially- (accessory) available) To audio output port To audio output port RGB video cable Component Computer RCA video S-Video (commercially- video cable cable or cable cable available) (commercially- (accessory) (commercially- VGA-HD15 availa
ページ4に含まれる内容の要旨
User's Guide Projection preparation and adjustments "Turning the Projector On" Set the [R/C] switch Check that the power cable is connected to the projector and to "ON". to the electrical outlet. For a video source, press the [Play] button. Turn the power on for all input equipment. Projection starts after a short period. Press the button. (Operation) indicator Flashes green (warm-up in progress/approx. 40 seconds) → Lights green (projection in progress) If "Password Protect" ha
ページ5に含まれる内容の要旨
Select the images to be projected. If only one signal source is connected, images from that source will be projected automatically. If more than one device is connected to the projector, use the [Source] button to select the image source to be projected. If using the or buttons to select the source, you can change the signal setting by pressing the button repeatedly. To select images to be Active window 1. Press the button. projected while viewing Computer (An
ページ6に含まれる内容の要旨
Adjusting projected Adjusting the projection angle Adjusting the image size and focus images While pulling the foot adjust lever, Focus adjustment lift up the front of the projector so that the front adjustable foot can Fine adjustments to extend. The Auto Keystone image size function will operate when the Enlarge: Turn to "W" projector is tilted. Reduce: Turn to "T" To retract the front adjustable foot, gently push down on the projector User's Guide "Zoom Function" while pulling the fo
ページ7に含まれる内容の要旨
Wall Shot If projecting onto a Images can be automatically corrected and projected without loss of original colour onto surfaces which blackboard or wall are not white. In addition, the tints can be adjusted in accordance with the brightness of the room. 1. Press the button. Sales by branch for January–February period Sales by branch for January–February period 60 60 60 60 January sales January sales 52 February sales February sales 50 Sales targets 50 50 52 Sales targets 50 48 48
ページ8に含まれる内容の要旨
Functions for Enhancing Projection Wireless Mouse Function Using the remote When projecting images from a computer, the accessory projector's remote control can be used to control for one-person operate the computer's mouse pointer. presentations Moving the mouse pointer Mouse clicks Left click Right click Double-click: Press twice in rapid succession. Drag and drop 1. Hold down the button for approx. Displaying previous or next slides in a 1.5 seconds. PowerPoint slideshow The
ページ9に含まれる内容の要旨
Video Position Adjust Audio Tracking : 0000 Effect Sync. : 0 Setting Brightness : 0 User's Logo Contrast : Auto Manual Adjust Advanced1 Sharpness : 0 Advanced2 Color Mode Select [Presentation ] Select About Resolution :: Auto Manual : Reset All [ ] Preset Set Reset Execute [ ]: Select [ ]: Enter [Menu]: Exit E-Zoom Function Enlarging parts of This function lets you enlarge and reduce parts of images such as graphs and tables that you an image would like to view in great
ページ10に含まれる内容の要旨
Effect Function Emphasising parts of an You can display a pointer icon and draw lines on the image being projected to emphasise parts image of the image that you want to draw attention to. Sales by branch for January–February period Sales by branch for January–February period 60 60 60 60 January sales January sales February sales February sales 52 52 Sales targets 50 Sales targets 50 50 50 48 48 43 43 Using the pointer icon 40 40 40 40 38 36 38 36 30 31 30 30 31 30 29 29 20 20 20 20 10 10
ページ11に含まれる内容の要旨
Other useful functions Some examples of the projector's many useful functions include projecting EasyMP Setup Guide images from a computer connected via a network and automatically Network EasyMP Operation Guide sending email notifications if errors occur with the projector, such as if the Correspondence lamp cuts out during projection. User's Guide The colour mode Presentation "Selecting the Projection changes as follows Theatre Color Mode each time this button Quality (Colour Mode Dy
ページ12に含まれる内容の要旨
User's Guide List of configuration setting menus "Using the Configuration Menu Functions" During computer During computer During component video During S-Video or During RGB video (digital RGB) input Main menu Sub-menu (Video) (analogue RGB) input (YCbCr or YPbPr) input composite video input input or EasyMP Brightness Position Position Position Position Video Position Adjust Contrast Tracking Brightness Brightness Brightness Audio Tracking : 0000 Effect Sync. : 0 Sharpness Contrast Contra
ページ13に含まれる内容の要旨
Troubleshooting User's Guide "Troubleshooting" If you cannot select images from a computer connected by If a problem occurs with the projected images even though the projector is set up and connected a computer cable, or the correctly, check the following points. images do not project correctly If the following does not solve the problem User's Guide "When the Indicators Provide No Help" The computer cannot Was the projector and If the connection is made while the power is already turned o
ページ14に含まれる内容の要旨
Reading the Indicators (Operation) indicator (Lamp) indicator (Temperature) indicator The projector is provided with indicators to notify you of the operating status of the projector. The following tables show what the indicators mean and how to remedy the problems that they indicate. If the indicator is flashing or lit red Problem/Warning lit flashing off Red Red Red Internal error Disconnect the power cable from the electrical outlet. Then contact your dealer or the nearest address prov
ページ15に含まれる内容の要旨
/ The lamp will switch off automatically If the problem is not fixed, stop Internal Red Red and projection will stop. If the projector using the projector and temperature Wait for approximately 5 minutes. is close to a disconnect the power plug from error Then disconnect the power cable and wall, move it the electrical outlet. (overheating) check the points to the right. away from the Then contact your dealer or the wall. nearest address provided in the "International Warranty If y
ページ16に含まれる内容の要旨
Replacing the Lamp How to replace the lamp You will need the provided accessory screwdriver or another flathead screwdriver. Turn off the power, wait for the cool down period to end (about Disconnect the 30 seconds) then disconnect the power cable. power cable. Remove the lamp cover from the underside of the projector. Remove the cover when the projector has sufficiently cooled down. It takes about a further one hour from when the cool down period has finished for the lamp to be cool enou
ページ17に含まれる内容の要旨
Loosen the two lamp fixing screws. Lift the handle and pull out the old lamp. 2 If the lamp has broken, request a replacement lamp from EPSON, or the place of purchase. 1 Safety Instructions/Worldwide Warranty Terms
ページ18に含まれる内容の要旨
Holding the lamp facing the correct way, insert the lamp Install the new lamp. until it clicks into place then tighten the two fixing screws. Install the lamp Slide the cover until it clicks into place. cover. • Install the lamp securely. If the lamp cover is removed, the lamp turns off automatically as a safety precaution. Moreover, the lamp will not turn on if the lamp or the lamp cover is not installed correctly. • Dispose of used lamps properly in accordance with local regulations. Procee
ページ19に含まれる内容の要旨
Resetting the Lamp Operating Time After replacing the lamp, be sure to reset the Lamp Operating Time from the configuration menu. Do not reset the Lamp Operating Time except after the lamp has been replaced. If you do, the Lamp Operating Time will no longer be displayed correctly. The configuration menu is displayed. Press . Lamp Lamp : 1900H 1900H Select "About" Reset Lamp Timer Reset Lamp Timer : Execute Execute Source Source : Computer Computer "Reset Lamp Timer" Input Signal Inpu
ページ20に含まれる内容の要旨
User's Guide List of Supported Monitor Displays "List of Supported Monitor Displays" Resolutions for resized display Signal Refresh rate (Hz) Resolution (dots) (dots) 1024 × 560 VGAEGA 640 × 350 *1 VGA 60/72/75/85/100/120, iMac 1024 × 768 640 × 480 *1 1024 × 768 SVGA 56/60/72/75/85/100/120, iMac 800 × 600 *1 1024 × 768 XGA 1024 × 768 60/70/75/85/100/120, iMac *2 SXGA 70/75/85/100 1024 × 768 1152 × 864 *2 1024 × 768 1280 × 960 SXGA 60/75/85 *2 960 × 768 1280 × 1024 *2 SXGA+ 60/75/85 1024 × 768 1
