ページ1に含まれる内容の要旨
HDP404
1080p DLP™ Projector
Users Manual v1.3
ページ2に含まれる内容の要旨
2 FCC Warning Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no gua
ページ3に含まれる内容の要旨
3 TABLE OF CONTENTS Safety Warnings 4 Introduction 5 Positioning the projector 7 Choosing the aspect ratio 8 Video connectors 8 Connecting a video device 9 Composite (RCA) video connection 9 S-video connection 9 Component (RCA) connection 9 SCART RGB connection 9 Digital connections 10 DVI connection 10 HDMI connection 10 Computer connections 10 RS-232 connections 10 Displaying an image
ページ4に含まれる内容の要旨
8’ / 2.4 m 3’ / 1 m ’ / 1 m 3 4 Important Operating Considerations for Safety • Place the projector in a horizontal position no greater than 15 degrees off axis. • Locate the projector in a well-ventilated area without any obstructions to intake or exhaust vents. • Do not place the projector on a tablecloth or other soft covering that may block the vents. • Locate the projector at least 4' (1.2 m) away from any heating or cooling vents. • Use only Knoll-approved ceiling mounts. • Use
ページ5に含まれる内容の要旨
5 Base Zoom ring Focus ring Receiver (IR) Product specifications To read the latest sp
ページ6に含まれる内容の要旨
6 • HDMI™ (High Definition Multimedia Interface) • Component (RCA) • SCART RGB (you must enable this connector, see page 9) • S-video • Composite video (RCA) See “Video connectors” on page 9 for details. The projector also provides the following connectors: • RS-232 for serial control (not included on the HD108) • 12-volt DC output (see below) 12-volt DC output The 3.5mm mini-jack trigger provides a 12-volt, 0.25 amp DC output. It provides a constant output while the
ページ7に含まれる内容の要旨
7 Position the projector the desired distance from the screen. The distance from the lens of the projector to the screen, the zoom setting, and the video format determine the size of the projected image. Projector Positioning The projected image becomes larger as the distance between the unit and screen increases. The manual zoom allows the distance from the screen to be within a minimum and maximum range. See the chart on the next page for details. The example belo
ページ8に含まれる内容の要旨
8 Please note the HD404 projectors are designed for use with 16:9 screens. They also have a built in scaler for use with 2.35:1 screens. To display images at the highest definition possible in 2.35:1 or cinemascope (most major movies are filmed in 2.35:1) an anamorphic lens is required. We recommend the Panamorph brand, which has fixed, movable and motorized anamorphic lens for use with the HDP404. Choosing the aspect ratio Aspect ratio is the ratio of the image width to image hei
ページ9に含まれる内容の要旨
9 The first step for connecting video is determining what type of output connectors your video Component RCA device has. If there is more than one output, select the one with the highest quality. The best quality ranking, with 1 being the highest, is: 1. M1-DA/DVI or HDMI (both are digital inputs). With a M1-DA to HDMI adaptor the HDP410, HDP420 and HDP460 have two HDMI inputs. 2. Component /SCART RGB video (RCAs) 3. S-video 4. Composite Vide
ページ10に含まれる内容の要旨
10 Digital connections The M1-DA/DVI and HDMI (High-Definition Multimedia Interface) connectors are digital and yield the highest quality image. It is common for these signals to be encrypted with HDCP (high-band width digital-content protection). Your new projector ships standard with decryption codes so you can enjoy these high quality, all digital images. This projector uses the M1-DA connector, which has the following advantages: • allows connection to a digital DVI source •
ページ11に含まれる内容の要旨
11 When the lamp comes on, the start-up screen is displayed and the LED is steady green. It can take a minute for the image to achieve full brightness. ? No start up screen? Get help on page 13 Plug in, connect, and turn on your video device. The video device’s image should appear on the turn on video device projection screen. If it doesn’t, press the Source button on the remote until the image appears. ? No image? Try pressing the Auto Image button on the remote. Get
ページ12に含まれる内容の要旨
12 Sleep Timer The projector also has a sleep timer feature that automatically turns the projector off after four hours. See page 21. Turning off the projector Press the Power button on the remote or keypad to turn the projector off. The lamp turns off and the LED blinks green for one minute while the fans continue to run to cool the lamp. While the LED is blinking green, the projector does not accept any user input. Once the cooling process is complete, the LED lights solid green an
ページ13に含まれる内容の要旨
13 The following tables show common problems. In some cases, more than one possible solution is provided. Try the solutions in the order they are presented. When the problem is solved, you can skip the additional solutions.
ページ14に含まれる内容の要旨
14
ページ15に含まれる内容の要旨
15 Still need assistance? If you need assistance, visit our website at www.knollsystems.com, or call us at 1 800 566 5579. during Pacific west coast time. This product is backed by a limited warranty. An extended warranty plan may be purchased from your retailer or dealer. When sending the projector in for repair, we recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its full
ページ16に含まれる内容の要旨
16 Using the remote control The remote uses two provided AA batteries. They are easily installed by sliding the cover off the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover. Navigation buttons To operate, point the remote at the projection screen or at the front of the projector (not at the video device or computer). The range of optimum operation is up to 30 feet (9.14m).
ページ17に含まれる内容の要旨
17 • Turn on Overscan to remove noise on the edges of the video image (page 19). • Change the Aspect ratio (page18). Aspect ratio is the ratio of the image width to image height. TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are 1.78:1, or 16:9 (the projector’s default). Choose the option that best fits your input source in the menus, or press the Resize button on the remote to cycle through the options. See page16. • Select a specific Color Space. See page 20. •
ページ18に含まれる内容の要旨
18 Menu options are grayed out only if the source is selected but no signal is present. For example, if the projector is set to a video source but the source, such as a DVD player, is turned off video menu options are grayed out. Picture Menu Increasi
ページ19に含まれる内容の要旨
19 Gamma: Gamma tables contain preset intensity configurations optimized for the input source. You can select a gamma table that has been Gamma specifically tuned for either film, CRT (Cathode Ray Tube), Video, PC, or Bright Room input. (Film input is material originally captured on a film camera, like a movie; video input is material originally captured on a video camera, like a TV show or sporting event.) White Peaking increases the brightness of whites that are ne
ページ20に含まれる内容の要旨
20 Color Space: this option applies to computer and Color space component video sources. It allows you to select a color space that has been specifically tuned for the input signal. When Auto is selected, the projector automatically determines the standard. To choose a different setting, turn off Auto, then choose RGB for computer sources, choose either REC709 or REC601 for component video sources. Color Temperature Color Temperature: changes the intensity of the colors
