ページ1に含まれる内容の要旨
4
3
2
1
Self Cleaning Free-Standing
Installation
Electric Range
EER2000, EER3000 JBP24, JBP26, JBP30, JBP35, JBP48, JBP64, JBP65,
Instructions
JBP66, JBP67, JBP70, JBP78, JBP79, JBP85, JB940, JB960, JB965
“If you have questions, Call 800-GE-CARES or visit our website at:
www.GEAppliances.com”
Skill Level: High Average Low
Completion Time: 1 to 3 Hours
Proper installation is the responsibility of the installer. Product failure due to improper installation
is not covered under the GE Appli
ページ2に含まれる内容の要旨
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS For Your Safety WARNING: To reduce the risk of tipping, the appliance must be WARNING: For personal safety secured by properly installed anti-tip remove house fuse or open circuit bracket packed with the appliance. breaker before beginning installation. Failure to do so could result in serious injury or even death. WARNING All rough-in and spacing dimensions must be met All ranges can tip for safe use of your range. Electricity to the r
ページ3に含まれる内容の要旨
EASY INSTALLATION OF YOUR NEW 30" WALL OVEN Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely a
ページ4に含まれる内容の要旨
Installation Instructions Installation Required Clearances A See Ilustrations below for all rough-in and spacing dimensions. The range may be placed with 0” clearance (flush) at the back wall and side walls of the cabinet. **30" MIN ***6" MIN MINIMUM DIMENSIONS BETWEEN **15" MIN COOKTOP, WALLS, AND ABOVE THE COOKTOP. * Make sure the wall covering, countertop and cabinets around the range can with- *0" *0" stand the heat (up to 200°F.) generated by the range. ** Allow 30” Minimum clearance betwee
ページ5に含まれる内容の要旨
Installation Instructions Electrical Connections B Making the Electrical Connection B1 Electrical Requirements Remove the wire cover (on the back of the This appliance must be supplied with the proper range) by removing 5 screws using a 1/4” nut voltage and frequency, and connected to an driver. Do not discard these screws. individual properly grounded branch circuit; protected by a circuit breaker or fuse having 3 amperage as specified on the rating plate. The RE ratin
ページ6に含まれる内容の要旨
Installation Instructions Electrical Connections cont. B Attach the green lead NEW CONSTRUCTION AND FOUR B8 Ground below the junction WIRE CORD CONNECTION KIT Screw block with the ground screw that was Complete 4 wire B3 3 Screws removed earlier. cord kit. Below are Gound step by step Screw and Ground Strap instructions on Connect the red Location B9 how to install the and black leads to Strain kit. the outside Relief Connection Clamp terminals and the Plate Red or white lead to the Black Whit
ページ7に含まれる内容の要旨
Installation Instructions Electrical Connections cont. B Connect the outer wires to the outside THREE- WIRE CORD CONNECTION KIT B7a terminals and the center wire to the center terminal. Do not remove the Grounded Neutral 3 ground strap Complete 3 Terminal Grounded Screws B3a (White) Neutral wire cord kit. Terminal Below are step (White) Ground Strap by step Center Ground Screw Wire instructions on Outer how to install Strain Wire Connection Relief the kit. Plate Clamp Center Wire Outer Remove
ページ8に含まれる内容の要旨
Installation Instructions C Installing the Anti-Tip Bracket Installing The Bracket in Wood C1 Locating The Bracket C2 or Concrete The anti-tip bracket, provided with your literature INSTALLATION–WOOD CONSTRUCTION and broiler pan, must be properly installed to prevent the range from tipping. Please refer to a. Locate the centers of the four holes identified the instructions provided with your anti-tip in Fig. 1 as Floor-Wood and Wall. bracket. b. Drill a 1/8" pilot hole through the pre-marked ar
ページ9に含まれる内容の要旨
Installation Instructions D Installing the Range Storage Drawer Removal CAUTION: The oven door is heavy. You may need help lifting the door Pull the drawer D1 high enough to slide it into the out until it stops hinges slots. Do not lift the door by the handle. Lift the front of D2 the drawer until Replacing the Oven Door the stops clear the guide. Pick the Oven Door up D9 by placing both hands on Stop D3 Remove the each side. The door is drawer. heavy so you may need help. Do not lift the door b
ページ10に含まれる内容の要旨
Installation Instructions D Installing the Range cont. Replacing the Storage Drawer Place the drawer D13 rail on the guides. Push the drawer D14 in until it stops. Stop Lift the front of the drawer and push in D15 until the stops clear the guides. Lower the front of the drawer and D16 push in until it closes. SPECIAL INSTRUCTIONS IF YOU HAVE PROBLEMS WHILE REPLACING THE STORAGE DRAWER IF DRAWER WON'T CLOSE Drawer Does Not Close Drawer Front Panel Tipped Away From Completely Body Side Power Cord
ページ11に含まれる内容の要旨
Installation Instructions Final Check List E Check to make sure the circuit breaker is closed (Reset) or the circuit fuses are replaced. Be sure power is in service to the building. Check to be sure that all packing materials and tape on metal panel (if applicable) under control knobs have been removed. Operation Check List F Check to make sure the Clock display is energized. If a series of horizontal red lines appear in the display, disconnect power immediately. Recheck the range wiring connect
ページ12に含まれる内容の要旨
NOTES Pub. No. 31-10463 12 229C4053P447-3
