ページ1に含まれる内容の要旨
If range does not operate: Moving the range:
Check that the circuit breaker is not tripped
When moving range, slide range onto cardboard
or the house fuse blown.
or hardboard to prevent damaging the floor
WARNING
Check that the power supply cord is plugged
covering.
into the wall receptacle.
If removing the range is necessary for cleaning
Check that gas line is turned on.
or maintenance:
See Use and Care Guide for troubleshooting list.
1. Remove the storage drawer.
2. Shut off the gas s
ページ2に含まれる内容の要旨
Before you start... Product dimensions Grounded electrical Your safety and the safety of outlet is required. See others are very important. “Electrical requirements,” We have provided many important safety Page 3. message in this manual and on your Proper gas supply appliance. connection must be Always read and obey all safety messages. available. See “Gas supply requirements,” This is the safety alert symbol. Page 3. This symbol alerts you to potential hazards that can kill or hurt you and ot
ページ3に含まれる内容の要旨
Tools needed Electrical requirements level Recommended WARNING ground method 3/8" drive For personal safety, this range is equipped with a ratchet flat-blade power supply cord having a 3-prong ground screwdriver plug. To minimize possible shock hazard, the wood floor: cord must be plugged into a mating 3-prong, 1/8" drill bit ground-type outlet, grounded in accordance with Electrical Shock Hazard concrete/ceramic floors: the National Electrical Code, ANSI/NFPA 70 — 3/16" carbide-tipped masonr
ページ4に含まれる内容の要旨
Check cooktop E burners for proper flame Plug power D supply cord into grounded outlet Check broiler E burner for proper flame Remove shipping A material. Make proper D Remove oven gas connection racks and parts package. Check oven E burner for proper flame Install anti- B tip bracket Secure range C with anti-tip Level range bracket C Replace D storage drawer Installation steps Preparation A WARNING 1.Put on safety glasses and gloves. Do Not use oven door handle to lift or move the range. E
ページ5に含まれる内容の要旨
Before moving range across floor, check that range is still on cardboard shipping base to Operating position C protect floor covering. front leveling leg 6.Making sure the anti-tip bracket is installed: anti-tip • Look for the bracket anti-tip bracket securely attached to range foot 8.Place rack in oven. Place level on rack, floor. first side to side; then front to back. • Slide range back so rear range foot is under rear leveling leg If range is not level, pull range forward until anti-tip b
ページ6に含まれる内容の要旨
H I G H T H G I L F F O If your oven hasone of these Check operation E 18.Follow the instructions for your type electronic control pads: of oven controls. Electronic ignition system Note: A faint ticking sound will be heard while Cooktop and oven burners use electronic TIMER OVEN CLOCK the oven burner lights. The oven burner should SET LIGHT SELF-CLEANING OVEN TIMER AUTO ignitors in place of standing pilots. When a OFF CLEAN light within 8 seconds. UNDO FIRST/ cooktop control knob is turned to
ページ7に含まれる内容の要旨
Check operation E (cont.) If your oven has this type of electronic Check operation of oven broil 23.Check the broil burner for control pad: proper flame. The flame should be 1/2" burner long, with inner cone of bluish-green, and outer mantle of dark blue, and ON 888° F 88:88 HEAT BAKE BROIL CLEAN TIMER should be clean and soft in character. No 22.Follow the instructions for your type yellow tips, blowing or lifting of flame of oven controls. TIMER START OFF SET CUSTOM AUTO BAKE TEMP TEMP CLOCK L
ページ8に含まれる内容の要旨
reinstall reinstall 6.Reinstall the storage drawer. Complete 3.Surface 3.Surface one of the one of the orifice orifice screws installation sections D through E, Pages 5-7. screws Burners: Burners: spud spud Checking for proper cooktop burner and oven Remove burner Remove burner spark electrode spark electrode flame is very important. caps. Use a caps. Use a orifice orifice spud spud Phillips or Phillips or holder holder Quadrex Quadrex YOU MUST ADJUST “LOW” SETTING FOR screwdriver to screwdriver
ページ9に含まれる内容の要旨
If range does not operate: Moving the range: Check that the circuit breaker is not tripped When moving range, slide range onto cardboard or the house fuse blown. or hardboard to prevent damaging the floor WARNING Check that the power supply cord is plugged covering. into the wall receptacle. If removing the range is necessary for cleaning Check that gas line is turned on. or maintenance: See Use and Care Guide for troubleshooting list. 1. Remove the storage drawer. 2. Shut off the gas s
