ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS
30" (76.2 CM) ELECTRIC DROP-IN RANGES
Table of Contents
RANGE SAFETY............................................... 2
INSTALLATION REQUIREMENTS.................. 2
Tools and Parts ............................................. 2
Location Requirements ................................. 2
Electrical Requirements ................................ 4
Countertop Preparation................................. 4
INSTALLATION INSTRUCTIONS.................... 5
Prepare Drop-In Range .
ページ2に含まれる内容の要旨
. WARNING Tip Over Hazard A child or adult can tip the range and be killed. Securely attach mounting screws to cabinet. Reattach mounting screws if the range is moved. See installation instructions for details. Failure to follow these instructions can result in death or serious burns to children and adults. Making sure the mounting screws are installed: Mounting • Remove side trim from both sides of the range. screw � Look for screws securely attached to cabinet. � Replace side tr
ページ3に含まれる内容の要旨
Front view of cabinet cutout Product Dimensions B D E C C A C F B E G D F A J A. Top of countertop must be level across front, and front to back. H B. Locate electrical junction box on rear wall. Bottom of junction box I should be 30¾" (78.1 cm) max. from top of countertop. C. 28½" (72.4 cm) min. opening width 29³⁄₈" (74.6 cm) opening is recommended if available A. 30³⁄₄" (78.1 cm) recessed E. 21" (53.3 cm) cooktop depth D. ⁷⁄₈" (1.9 cm) min. required between cutout and cabinet door or hinge
ページ4に含まれる内容の要旨
Electrical Requirements Countertop Preparation If codes permit and a separate ground wire is used, it is Front edges: recommended that a qualified electrical installer determine that You may need to shave or cut the trim of formed or metal front- the ground path and wire gauge are in accordance with local edged countertops to clear the 30" (76.2 cm) width of the codes. cooktop. Check with a qualified electrical installer if you are not sure the range is properly grounded. This range must be
ページ5に含まれる内容の要旨
INSTALLATION INSTRUCTIONS 3. Grasp the edges of the oven door with both hands and close the oven door until it stops. Lift and pull oven door toward you Prepare Drop-In Range and remove. Set the oven door aside on a covered work 1. Decide on the final location for the range. Locate existing surface. wiring to avoid drilling into or severing wiring during installation. WARNING Excessive Weight Hazard Use two or more people to move and install range. Failure to do so can result in back or oth
ページ6に含まれる内容の要旨
Make Electrical Connection Electrical Connection Options Chart WARNING If your home has: Go to section: 4-wire 4-wire Cable from Home Power Supply Electrical Shock Hazard ½" (1.3 cm) Disconnect power before servicing. Use 8 gauge solid copper wire. 3-wire 3-wire Cable from Home Power Supply Electrically ground oven. Failure to follow these instructions can result in death, fire, or electrical shock. ½" This range is manufactured with a neutral (white) power supply (1.3 cm) wire and a cabinet-
ページ7に含まれる内容の要旨
2. Push against seal area of front frame to push range into 3-Wire Cable from Home Power Supply cabinet until shipping feet almost contact cabinet. IMPORTANT: Use the 3-wire cable from home power supply where local codes permit a 3-wire connection. A B C G H A D A. Shipping foot E 3. Use a Phillips screwdriver to remove and discard shipping I feet. F 4. Push range completely into cabinet and center range in cabinet cutout. A. Cable from home power supply F. 4-wire flexible cable from range
ページ8に含まれる内容の要旨
6. Slide top end of each trim piece upward onto range side rails. Complete Installation 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. 3. Dispose of/recycle all packaging materials. 4. For range use and cleaning, read the Use and Care Guide. Check Operation of Cooktop 1. Turn power on. “PF” should appear in the display. 2. Push in and turn each cooktop control knob to HI.
