ページ1に含まれる内容の要旨
GAS HOB
ZGF 7820
INSTRUCTION BOOKLET
Please read this instruction booklet before using the appliance
GB
ページ2に含まれる内容の要旨
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation Unstable or misshapen pans should not be used on This appliance must be installed and serviced by a the hob as unstable pans can cause an accident by competent person as stated in the Gas Safety tipping or spillage. (Installation and Use) Regulations Current Editions Never leave the hob unattended when
ページ3に含まれる内容の要旨
Contents For the Installer For the User Important Safety Information 2 Instructions for the Installer 7 Description of the Hob 4 Important safety requirements 8 Operation 5 Installation 9 Maintenance and Cleaning 5 Building In 10 Something Not Working? 6 Electrical connections 11 Guarantee/Customer Service 15 Wiring Diagram 12 European guarantee 16 Fault Finding 12 Commissioning 14 Conversion from Natural Gas to LPG 14 Guide to Use the instructions Environmental Information The following symbo
ページ4に含まれる内容の要旨
5 Description of the Hob 2 3 1 2 4 1. Auxiliary Burner 2. Semi-rapid Burners 3. Ultra-rapid Triple-crown Burner 4. Rapid Burner 5. Control knobs 4
ページ5に含まれる内容の要旨
inserire Operation Hob burners termocoppie To light a burner: push in the relevant control knob and turn it anticlockwise to maximum position; then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used (see table). Burner minimum maximum diameter diameter Ultra-rapid (triple-crown) 180 mm 260 mm Large (rapid) 180
ページ6に含まれる内容の要旨
YES Cast Iron Pan Supports The hob has cast iron pan supports. Take care when removing them. They are very heavy and could damage the hob or your kitchen furniture if you let them fall down. To keep the pan supports in the correct position, they are hooked into hinges at the back of the hob. When removing the pan supports, lift them up as shown in the diagram. Never turn the pan supports on the hinges, this could damage them. NO Wash the pan supports using hot soapy water. If necessary, a paste
ページ7に含まれる内容の要旨
Instructions for the Installer Ignition HT Spark Engineers technical data Spark Generator Ispra Control's BF 50066 OVERALL DIMENSIONS 220- 240V 0.6 VA T 120 Spark Gap Fixed Width: 680 mm Depth: 510 mm Rear Left Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) CUT OUT DIMENSIONS Front Left Burner (auxiliary) Heat Input 1.0 kW (3413 BTU/HR) Width: 560 mm Depth: 480 mm Rear Right Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) SUPPLY CONNECTIONS Gas: Front Right Burner (rapid) R 1/2 inch
ページ8に含まれる内容の要旨
100 mm 100 mm 50 mm 50 mm 50 mm 50 mm 600 mm 600 mm Important safety requirements This hob must be installed in accordance with the Gas FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. 813 Current Editions and the ETCI Rules for Electrical Installations. 700 mm Provision for ventilatio
ページ9に含まれる内容の要旨
Installation IMPORTANT: This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a competent person. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. On the end of the shaft, whic
ページ10に含まれる内容の要旨
Building In Building over a cupboard or Building over a kitchen unit with drawer door If the hob is to be installed above a cupboard or drawer it Proper arrangements must be taken in designing the will be necessary to fit a heat resistant board below the furniture unit, in order to avoid any contact with the bottom base of the hob on the underside of the work surface. of the hob which can be heated when it is operated. The It is also recommended to carry out the electrical recommended solution i
ページ11に含まれる内容の要旨
Seal a FO 0199 Electrical connections Any electrical work required to install this hob Permanent Connection should be carried out by a qualified electrician or In the case of a permanent connection, it is necessary competent person, in accordance with the current that you install a double pole switch between the hob regulations. and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the THIS HOB
ページ12に含まれる内容の要旨
Wiring Diagram L A. IGNITOR SWITCH 1 B. IGNITOR UNIT A 0 2 3 4 220/240 5 6 B N Fault Finding Preliminary Electrical Systems PLUG (with cover SOCKET removed) (face view) Check ( ) Earth Wire ( ) E Brown Blue Green/Yellow START Isolate appliance Neutral Wire and carry out: Blue A: Earth Continuity N L check. Blue Green Brown Yellow Carry out: Electricity supply YES NO Carry out: D: Resistance to should now be C: Polarity check. Earth check. satisfactory. A. EARTH CONTINUITY CHECK - Appliance m
ページ13に含まれる内容の要旨
Ignition System / Gas Ignition YES Check gas supply at Ignitor does not spark burner NO Check plug top fuse and Light burner manually replace if necessary Check polarity and Check by pass simmer earth continuity of adjusted supply point Check position of the Check earth continuity electrode of appliance Check continuity from the tip of Check fitting of burners Check continuity from 'N' on the each electrode to the mains connector block and "O" on terminals 1 to 4 on the ignitor the ignitor unit
ページ14に含まれる内容の要旨
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: Re-ignite the burner and set to MIN. Remove the control knob. To adjust, use a thin bladed screwdriver and turn th
ページ15に含まれる内容の要旨
Guarantee/Customer Service Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: · The appliance has been correctly installed and used only on the electricity supply stated on the rating p
ページ16に含まれる内容の要旨
European guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qualifications: • The appliance guarantee starts from the date you first purchased the appliance which will be evidenced by production of a valid purch
ページ17に含まれる内容の要旨
17
ページ18に含まれる内容の要旨
18
ページ19に含まれる内容の要旨
19
ページ20に含まれる内容の要旨
www.zanussi-electrolux.co.uk 35687-8702 11/06 Grafiche MDM - Forlì
