ページ1に含まれる内容の要旨
Model APS-410a
Owner’s Manual
4 Button Remote Security System
with Dual Stage Shock Sensor
IMPORTANT ! In order to provide the highest possible level of security to your vehicle, this
system is equipped with selectable manual override circuitry. It is possible that you will need to
manually override your security system if the transmitter becomes lost, or inoperative due to
battery failure. Reading the sections on "MANUALLY OVERRIDING YOUR SYSTEM" is
necessary to fully understand the procedu
ページ2に含まれる内容の要旨
YOUR “Code Hopping” TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system. Some of today’s sophisticated auto thieves use a device known as a code grabber, which will receive and store the signal from your keychain transmitter, and re transmit at a later time to disarm your system. Your code hopping transmitters will change their signal every time the button is
ページ3に含まれる内容の要旨
detected a open entry point after the learned delay expired. Closing the hood, trunk, or doors will correct the problem and you do not need to disarm the system to make the correction. Doors Lock - Optional ARMING THE SYSTEM - PASSIVE ( AUTOMATIC ) 1. Turn off the engine, exit the vehicle, and close and lock all doors, hood lid, and trunk lid. Dash mounted LED begins to flash rapidly, indicating 30 second pas- sive arming has begun. 2. Opening any protected entry point during the 30 second
ページ4に含まれる内容の要旨
DISARMING THE SYSTEM 1. As you approach the vehicle, press and release the Unlock button on the keychain transmitter. Dash mounted LED turns off. If passive arming was selected during the installation, then the LED will start flashing rapidly, indicating that the system is re-arming automatically. Open any door to suspend the automatic arming. Parking Lights flash two times. If the parking lights flashed three times, then the alarm was triggered in your absence. Before turning the key on, e
ページ5に含まれる内容の要旨
refer to the INTRUSION WARNING SIGNALS section of this manual to identify which zone was triggered. Doors Unlock - Optional Note:If the optional 2 step door unlock circuit is installed, when the unlock transmitter button is activated, the drivers door only will unlock, pressing the unlock button a second time will cause all doors to unlock. If your transmitter has a separate lock/unlock buttons, pressing the unlock button anytime after the first unlock command will cause all the vehicle doors
ページ6に含まれる内容の要旨
(Light Emitting Diode) turns on. The LED will remain on as long as the system is in valet mode. 3. To return to normal operation, press and release the push button switch any time the ignition is on. NOTE:Always remember to return the system to the NON VALET mode, after servicing, to ensure that the vehicle remains protected at all times. MANUALLY OVERRIDING YOUR SYSTEM: USING THE VALET SWITCH MANUAL OVERRIDE Your Security System can be disarmed without the use of the keychain transmit- ter. T
ページ7に含まれる内容の要旨
flashing the LED, first indicating the 10ths digit, pause and then the units digit. The unit will report the new code three times with a one second pause between each code, then the system will begin arming. If the LED flash pattern reports the previously stored code, the new code was not entered correctly. Please repeat steps 1 through 7 above considering the following. NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero) or no digit entered in any pla
ページ8に含まれる内容の要旨
1) Enter the vehicle and turn the ignition switch to the on position. Note: The siren will sound. 2) Within 5 seconds, press and release the pushbutton switch 1 time. 3) Within 5 seconds, turn the ignition switch off then on. 4) Within 5 seconds, press and release the pushbutton switch 1 time. 5) Turn the ignition switch off then on and start the vehicle. Note:If you have changed the programmed override code then substitute your new code tenths for step 2 above, and units for step 5 above.
ページ9に含まれる内容の要旨
While in the panic mode, anytime the DISARM button is pressed, the panic feature will continue for the allotted 30 seconds, however, the security system will be disarmed allowing the vehicle to start. ADDITIONAL REMOTE FUNCTION ( CHANNEL 3 ) This security system has an additional features that can be connected to a number of different optional accessories. Some of the more common uses for this channel are; Remote Trunk Release Remote Car Starter Remote Window Closure Remote Garage Door
ページ10に含まれる内容の要旨
APS 410a SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH...PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 SIREN CHIRP INDICATORS *1 CHIRP = ARM *2 CHIRPS = DISARM 3 CHIRPS = ARM / DOOR OPENED 4 CHIRPS = DISARM / INTRUSION * These chirps are optional, and can be de - activated. PARKING LAMP INDICATORS 1 FLASH = ARM 2 FLASHES = DISARM 3 FLASHES = DIS
