ページ1に含まれる内容の要旨
HTSD10X
10X Pan-Tilt Speed Dome Camera
200 New Highway, Amityville, NY 11701
www.specotech.com
800-645-5516
ページ2に含まれる内容の要旨
CONTENTS Warning & Caution 3 3 What s in the Box? General Features 4 Names of Each Part 5 Installation 6 A. Connection Methods 7 B. Ceiling Mount Type C. Embedded Mount Type Quick Operating Keys 8 9 Diagnostic
ページ3に含まれる内容の要旨
WARNING & CAUTION If y o u fai l to read this i nformation and handle the product incorrectly, serious injury may occur. This symbol is intended to alert the user to Never install the product in area exposed to the presence of un-insulated dangerous voltage within the product s enclosure that oil or gas. may be of sufficient magnitude to constitute a risk of electric shock to persons.
ページ4に含まれる内容の要旨
GENERAL FEATURES 100X Zoom Mini Speed Dome Quick Operation Keys 10X Optical Zoom with 10X digital zoom This camera provides quick functional keys in order to be easily controlled by any controller or DVR. ±0.02° dome system accuracy Various Surveillance Functions Auto Scan repeats pan and tilt between two preset With 0.1° technical accuracy, camera provides excellent positions with different speed and dwell time. sensitive and delicate controlling on preset mod
ページ5に含まれる内容の要旨
NAMES OF EACH PART 1. Surface Mount Adaptor 2. Cap Screw ( PT3/4 , 2EA ) 3. Dip Switch 4. Terminal Block 5. Main body 5
ページ6に含まれる内容の要旨
INSTALLATION A. CONNECTION METHOD A-1 1. Loosen the screws on the domes cover and remove it from the base. (Screws will not come out) 2. Loosen the screws which connect the mount cover and Main base and separate the dome cover from the main base. (Screws will not come out) 3. Connect power (12 VDC 1.5 A ) to Power and GND. 4. Connect video to Video and GND. 5. Connect communication cable to RS-485 connectors. 6. Connect alarm cable to GND like 1 and GND, 2 and GND,
ページ7に含まれる内容の要旨
INSTALLATION B. MOUNT 1. Attach the surface mount adaptor with 4 screws at the installation site. (FIG.4) 2. When you use pipe, please note the standard size of pipe. (FIG.5) 3. Re-assemble the domes. 7
ページ8に含まれる内容の要旨
QUICK OPERATING KEYS 1-64 + preset and 101~200 + preset are used for preset and 65-100 + preset used for functions. For example, to enter OSD MENU, press the button 95 +PRESET. Number Note Function 1 ~ 64, 100~200 +Preset PRESET Executing Preset 1 ~ 64 65 + Preset PRESET STATUS Display Preset Status 66 +Preset AUTO SCAN Executing Auto Scan 67 +Preset AUTO FLIP Selectable On/Off/Auto in Auto Flip function 71~78 +Preset GROUP TOU
ページ9に含まれる内容の要旨
QUICK OPERATING KEYS DIAGNOSTIC When the Power is turned on a DIAGONOSTIC is operated. The following messages are displayed on the monitor. CAMERA ID : 001 BAUD RATE : 2400 BPS WAITING PAN ORIGIN CHECK OK TILT ORIGIN CHECK OK TX CONNECTION TEST OK CAMERA COMM TEST OK A. Pan Origin Test Zero point of Pan is founded after Panning test. B. Tilt Origin Test Zero point of Tilt is founded after Tilting test. C. TX conne
ページ10に含まれる内容の要旨
OSD MENU SETTING If all the above Tests are OK, EEPROM CHECKING and EEPROM OK is displayed and the camera is ready to operate. A. OSD MENU TABLE 10 DOME SET CAMERA SET PRESET SET AUTO SCAN SET MAIN MENU CAMERA ID : CAM1 FLICKER : OFF/ON PRESET NO: 001 START ANGLE : XXX.X.XX.X RECOVER : OFF MIRROR : OFF/ON PRESET ID: PRESET01 END ANGLE : XXX.X.XX.X DOME SETUP MANUAL SPEED : 100°/S
ページ11に含まれる内容の要旨
OSD MENU SETTING To enter the OSD Menu, press the button 95 + PRESET. MAIN MENU DOME SETUP CAMERA SET AUTO SCAN TOUR PRAVACY PATTERN ALARM SECTOR EXIT * Use the joystick up - down to move the position and left - right to make selection B. Dome Setup To enter the Dome setup, move the joystick right to move the cursor. DOME SET CAMERA ID : CAM1 RECOVER : OFF MANUAL SPEED : 100°/S DEFAULT
ページ12に含まれる内容の要旨
OSD MENU SETTING B-2. DOME SET - RECOVER This feature allows the dome to work from the last setting before you use the dome manually (Auto scan, group tour, pattern or sectors) , after the set time, even power shut down and it turns on again. Recovery time can be programmed from 15 second to 90 seconds. The default setting is OFF. B-3. DOME SET - MANUAL SPEED Manual Speed of Pan/Tilt is selectable from 10°/sec up to 200°/sec. The default setting is 100°/sec B-4. DOME
ページ13に含まれる内容の要旨
correct password. In order to enter [PASSWORD] page, system lock status is must set as ON. OSD MENU SETTING Move joystick to right or left direction to select ON. The default setting is OFF. B-8-2. DOME SET [NEXT PAGE] [PASSWORD] To enter this page to set a password, move the joystick to the right direction. The password must be set by preset number from 001 to 255 (Default 99) A. OSD MAIN MENU TABLE (PAGE 11) The default setting is BLANK. ENTER PASSWORD BY ENTER
ページ14に含まれる内容の要旨
OFF/ON when the cursor is located each item. OSD MENU SETTING OSD DISPLAY CAMERA ID : OFF DEFAULT SETTING PRESET ID : OFF SECTOR ID : OFF COORDINATE : ON [PREVIOUS PAGE] B-8-4. DOME SET [NEXT PAGE] [SYSTEM STATUS] This page shows the information of this camera. SYSTEM STATUS PROTOCOL : PELCO D, P BAUD RATE : 2400 BPS FIRMWARE VER. : 2.00 DEFAULT SETTING UPGRADED DATE : 06.07,22 CAMERA MODULE : SDM100 [PREVIOUS PAGE] - Protocol a
ページ15に含まれる内容の要旨
OSD MENU SETTING - To clear memorized data, move joystick to the right direction when cursor is on each item. TOUR CLEAR TOUR CLEAR ARE YOU SURE? YES NO Press FOCUS NEAR button when the cursor is at YES in order to clear memorized data. Then each item such as tour, preset, sector and so on is displayed on the monitor about 2~3 seconds. After this process, the menu is returned to the previous page. * [PRESET CLEAR], [SECTOR CLEAR], [PRIVACY CLEAR], [PATTERN CLE
ページ16に含まれる内容の要旨
OSD MENU SETTING C. CAMERA SET CAMERA SET FLICKER : OFF MIRROR : OFF APERTURE : 10 D ZOOM : OFF WB MODE : AWB MODE PIC FLIP : OFF BLC : OFF D/N MODE : AUTO DSS MODE : OFF EXIT C-1. CAMERA SET - FLICKERLESS Flickerless feature is selected between 50Hz and 60Hz. The default setting is OFF (NTSC: 60Hz / PAL: 50Hz). Set flicker mode ON when power source is in discord with frequency. The default setting is OFF C-2. CAMERA SET - MIRRO
ページ17に含まれる内容の要旨
AWB Mode 3,200°K to 6, 000°K OSD MENU SETTING l Indoor up to 3,200°K l Outdoor up to 5,800°K l ATW Mode - 2,000°K to 10, 000°K C-6. CAMERA SET PIC FLIP Picture flip feature turns ths picture upside down. Move the joystick to the right or left direction to select OFF/ON. The default setting is OFF. C-7. CAMERA SET BLC (Back Light Compensation) The default setting is OFF and BLC modes can be OFF/ON. OFF Backlight compensation is not activated. ON Back light compens
ページ18に含まれる内容の要旨
OSD MENU SETTING D. PRESET SET To enter PRESET SET, move the joystick to the right direction. PRESET SET PRESET NO :001 PRESET ID :PRESET001------- PAN :XXX.XX TILT : XXX.XX SAVE DEFAULT SETTING EXIT D-1. PRESET PRESET NO. Up to 164 numbers of preset positions are available. Move joystick to the right or left direction to select a preset no. D-2. PRESET PRESET ID To set preset ID, select up to 16 characters using Joystick to the left or right. P
ページ19に含まれる内容の要旨
OSD MENU SETTING E. AUTO SCAN SET * 66 + preset button is working as AUTO SCAN after setting. AUTO SCAN SET START ANGLE : XXX.X.XX.X END ANGLE : XXX.X.XX.X DIRECTION : CW ENDLES : OFF DEFAULT SETTING SPEED : 10°/S DWELL TIME : 03 SAVE AND EXIT EXIT E-1. AUTO SCAN START ANGLE To set the start angle, press FOCUS FAR button then move the joystick to the starting angle which is to be memorized. Press FOCUS FAR button again is to escape. E-2. A
ページ20に含まれる内容の要旨
E-8. AUTO SCAN EXIT OSD MENU SETTING To escape this page, move the joystick to the right . F. TOUR SET 8 Programmable tours can be set and each tour is available to set up to 64 preset steps. After setting the data to each tour group, 71~78 + preset buttons are working as group tour # 1~8 TOUR SET TOUR NO : 01 TOUR TITLE : TOUR01 TOUR STEP : 01 DEFAULT SETTING PRESET NO. : 01 DWELL TIME : 03 SPEED : 200°/S SAVE EXIT F-1. TOUR SET TOUR NO. Max.
