ページ1に含まれる内容の要旨
Operating manual
- englisch -
DVB Satellite Receiver
UFS 700si/700sw
ページ2に含まれる内容の要旨
PREFACE Dear customer, this operating manual is intended to help you make the fullest use of the extensive range of functions offered by your new satellite receiver. We have tried to make the operating instructions as easy as possible to understand, and to keep them as concise as possible. To help you understand particular specialist terms that cannot be translated, we have added a short glossary at the end of the manual. The power switch is an environmentally friendly feature. If you will no
ページ3に含まれる内容の要旨
IMPORTANT INFORMATION The channels available on the satellites and transponders are subject to continual change. If changes do occur, the new channels have to be set in the receiver because the factory preset programming corresponds to the status on the date of manufacture. The information for these settings can be found on the Internet or in relevant magazines. Your receiver was equipped in the factory with the latest software version at that time. We are, however, constantly working on ada
ページ4に含まれる内容の要旨
CONTENTS PREFACE ................................................................................................................................. 2 IMPORTANT INFORMATION ...................................................................................................... 3 CONTENTS ............................................................................................................................... 4 SAFETY INSTRUCTIONS - IMPORTANT NOTES ..............................................
ページ5に含まれる内容の要旨
CONTENTS SKIP CHANNELS ................................................................................................................. 52 LOCK CHANNELS ................................................................................................................ 53 COPY CHANNELS TO THE FAVORITES LIST ............................................................................. 53 START BLOCKSELECTION (SELECTING SEVERAL CHANNELS) ................................................... 53 EDIT FAV
ページ6に含まれる内容の要旨
SAFETY INSTRUCTIONS - IMPORTANT NOTES 6
ページ7に含まれる内容の要旨
RECEIVER FEATURES/SCOPE OF SUPPLY The UFS 700si and UFS 700sw receivers are suitable for receiving FTA digital satellite TV and radio programmes. In addition to providing high-quality pictures and sound, series 700 receivers also feature an attractive design in a modern housing. The receivers have a comprehensive set of features, such as electrical audio output for Dolby Digital (AC 3), a video output and Videotext with memory. These receivers are available in silver or black housings. PRODUC
ページ8に含まれる内容の要旨
CONTROLS, DISPLAYS AND CONNECTIONS This section provides a brief description of all the controls, displays and connections. VIEW OF FRONT PANEL VIEW OF REAR PANEL Front panel controls and displays Rear panel controls and displays 1. On/Off switch (with mains disconnect) 1. LNB input 2. TV/R button for switching between 2. LNB loop-through input TV and radio mode 3. Audio outputs (L/R) cinch sockets 3. Channel select buttons ( ▼▲) 4. Video output (composite colour) 5. Electrical data stream
ページ9に含まれる内容の要旨
CONNECTION AND SET-UP The following section is intended specifi cally for specialist dealers. You only need read this section if you are performing the installation yourself. The “Connection Examples” section provides a sample confi guration. Do not connect the unit to the mains until all installation work has been properly carried out. Refer to the information in the “Safety Instructions” section. CONNECTING THE UNIT (SAT-IF CONNECTIONS) Connect the Sat IF input on the receiver to the satellite
ページ10に含まれる内容の要旨
CONNECTION AND SET-UP TV AND VIDEO RECORDER CONNECTION Connect the satellite receiver (TV Scart socket) and the TV set using a Scart cable (see “Connection Example”). If your TV has a stereo feature, you can receive the sound in stereo via the Scart connection. Use a further Scart cable to connect the satellite receiver (VCR/Scart socket) to the video recorder/PVR. For system reasons, the same video signals are to be found at the TV Scart socket as at the video cinch output. If you are recordi
ページ11に含まれる内容の要旨
REMOTE CONTROL Sound on/off Standby ... Videotext (Teletext) Switch on/input digits for channels, timer etc. (yellow) Call up Channel Options Call up Main Menu, sound/subtitles selection exit the menu and return to the TV picture (blue) Switch between TV/radio (red) Call up favorites selection Access Channel Notifi cation/Info (green) “Current” view in the EPG AV mode Volume Channel selection up/down Exit menu step by step Input confi rmation call up Channel List Changing
ページ12に含まれる内容の要旨
REMOTE CONTROL REMOTE CONTROL RC 660 The RC 660 remote control supports up to four devices (which are supplied with the RC 660 as standard) as well as the receivers of the UFD 5xx (not UFD 552, 554, 558) and UFD 4xx families. First switch all receivers off (at the power switch). To confi gure a receiver to an infrared code: Switch on the relevant receiver. On the remote control simultaneously press address 1 = + + . Then switch the receiver off again at the power switch and do the same for
ページ13に含まれる内容の要旨
FIRST INSTALLATION: General Before using your unit for the fi rst time, read the “Safety Instructions” and “Connection and Setup” sections. The “Connection examples” section provides a sample confi guration. Do not connect the unit to the power supply until all installation work has been properly carried out. The guidance given in the “First Installation” section assumes that the receiver has been properly connected, as per the “Safety Instructions” and “Connection and Set-Up” sections. First
ページ14に含まれる内容の要旨
FIRST INSTALLATION: General Use the buttons to select whether to replace the default channel list with one presorted for Germany, Austria, Switzerland or Italy. If you want to use the default channel list, choose “No” under “Restore Channellist”. Press the (green) button to move to the next menu. The following display appears: Use the buttons here to select the settings for your TV set. When doing this, refer to the operating instructions for your TV set! TV aspect ratio Here you select
ページ15に含まれる内容の要旨
FIRST INSTALLATION: General Picture format Here you select the type of screen display, depending on the setting of your TV format: - TV format “4:3”: Pan & Scan or Letterbox - TV format “16:9”: Always 16:9 or automatic TV-SCART-Output Select the type of video signal at the TV Scart socket here. Select the signal that your TV set can process. - CVBS – Colour Video Baseband Signal - RGB – Red/Green/Blue signal or - Y/C – S-Video signal (luminance/chrominance) Press the (green) button to move to t
ページ16に含まれる内容の要旨
FIRST INSTALLATION: DiSEqC™1.0 When selecting the satellite(s), make sure that your reception position is aligned to the desired satellite(s)! Number of Satellites Use the buttons to select how many satellites (max. 4) you would like to receive with your reception system. The following display appears (example): Use the buttons to select the fi rst satellite slot. Press to access the menu for the satellite settings. The following display appears (example): Satellite and Position Use the
ページ17に含まれる内容の要旨
FIRST INSTALLATION: DiSEqC™1.0 LNB Type Here use the buttons to select the LNB type used in your system. The choice is between “Universal” and “User-defi ned”. Universal: No further input is required, since all necessary frequency ranges are covered by a universal LNB. User-defi ned: If you choose not to use a universal LNB, you must here set the frequency ranges for which your LNB was confi gured. Use the buttons to select the frequency range to be changed (low, high or limit frequency). Use
ページ18に含まれる内容の要旨
FIRST INSTALLATION: SIMPLE LNB Satellite and position Use the buttons to select the desired satellite whose signal is to be received by the tuner. When you have selected your desired satellite, use the buttons to switch to the selection of the “LNB Type”. LNB Type Here use the buttons to select the LNB type used in your system. The choice is between “Universal” and “User-defi ned”. Universal: No further input is required, since all necessary frequency ranges are covered by a universal LNB
ページ19に含まれる内容の要旨
FIRST INSTALLATION: SIMPLE LNB User-defi ned: If you choose not to use a universal LNB, you must here set the frequency ranges for which your LNB was confi gured. Use the buttons to select the frequency range to be changed (low, high or limit frequency). Use the buttons or the digital input buttons to set the exact frequency for which your LNB was confi gured. Test transponder To check whether the settings that you have made are correct, use the buttons to move to the “Test transponder” fi
ページ20に含まれる内容の要旨
FIRST INSTALLATION: Single-cable system Use the buttons here to select “One Cable” as the “System”. Press the button to move to the next menu item. The following display appears: The various options for a single-cable system with Kathrein components are summarised at the end of this manual in the “Technical Appendix” section under “Examples of single-cable systems”. Number of Satellites Use the buttons to select how many satellites (max. 2) you would like to receive with your recept
