Makita 4340FCTの取扱説明書

デバイスMakita 4340FCTの取扱説明書

デバイス: Makita 4340FCT
カテゴリ: ノコギリ
メーカー: Makita
サイズ: 0.31 MB
追加した日付: 12/1/2013
ページ数: 16
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスMakita 4340FCTの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Makita 4340FCTに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Makita 4340FCTをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Makita 4340FCTのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Makita 4340FCTの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Makita 4340FCT 取扱説明書 - Online PDF
Advertisement
« Page 1 of 16 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Makita 4340FCTを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Makita 4340FCTの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

ENGLISH
Jig Saw
MODEL 4340T
MODEL 4340CT
MODEL 4340FCT
001905
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

ページ2に含まれる内容の要旨

SPECIFICATIONS Model 4340T 4340CT 4340FCT Length of stroke 26 mm 26 mm 26 mm Wood 135 mm (* 110 mm) 135 mm 135 mm Max. cutting capacities Steel 10 mm 10 mm 10 mm -1 2,800 800 - 2,800 800 - 2,800 Strokes per minute (min ) Overall length 236 mm 236 mm 236 mm Net weight 2.4 kg 2.4 kg 2.4 kg Safety class /II * For European countries • Due to our continuing programme of research and development, the specifications herein are subject to change without notice.  Note: Specifications may differ from c

ページ3に含まれる内容の要旨

GENERAL SAFETY RULES GEA001-3 WARNING: Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery- operated (cordless) power tool. SAVE THESE INSTRUCTIONS Work area safety 10. Use safety equipment. Always wear eye protec- tion. Safety equipment such as dust mask, non-skid 1. Keep work area clean and well lit.

ページ4に含まれる内容の要旨

19. Store idle power tools out of the reach of chil- 6. Check for the proper clearance beyond the dren and do not allow persons unfamiliar with workpiece before cutting so that the blade will the power tool or these instructions to operate not strike the floor, workbench, etc. the power tool. Power tools are dangerous in the 7. Hold the tool firmly. hands of untrained users. 8. Make sure the blade is not contacting the work- 20. Maintain power tools. Check for misalignment or piece before the sw

ページ5に含まれる内容の要旨

FUNCTIONAL CAUTION: DESCRIPTION  Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 001906 Selecting the cutting action This tool can be operated with an orbital or a straight line (up and down) cut- ting action. The orbital cutting action thrusts the blade forward on the cutting stroke and greatly increases cutting speed. To change the cutting action, just turn the cutting action changing lever to the desired cutting action position.

ページ6に含まれる内容の要旨

001956 Workpiece to be cut Number on adjusting dial Wood 4 - 5 Mild steel 3 - 5 Stainless steel 3 - 4 Aluminum 3 - 5 Plastics 1 - 4 CAUTION:  The speed adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work. The tools equipped with electronic function are easy to operate because of the following features. Constant speed control Electronic speed control for obtaining constant speed. Possible to get fine fin- is

ページ7に含まれる内容の要旨

001910 Keeping that situation, insert the saw blade into the blade clamp as far as the two protrusions of the blade can not be seen. 3 Return the tool opener to its original position. After installing, always make sure that the blade is securely held in place by trying to pull it out. CAUTION: 1  Do not open the tool opener excessively, or it may cause tool damage. 2 1. Blade clamp 2. Jig saw blade 3. Protrusions 001911 To remove the blade, open the tool opener to the position shown in the figu

ページ8に含まれる内容の要旨

001914 Bevel cutting CAUTION:  Always be sure that the tool is switched off and unplugged before tilting the tool base. With the tool base tilted, you can make bevel cuts at any angle between 0° and 45° (left or right). 001915 Loosen the bolt on the back of the base with the hex wrench. Move the base so that the bolt is positioned in the center of the bevel slot in the base. 1 3 2 1. Base 2. Bolt 3. Hex wrench 001916 Tilt the base until the desired bevel angle is obtained. The V-notch of the ge

ページ9に含まれる内容の要旨

Cutouts Cutouts can be made with either of two methods A or B. 001918 A) Boring a starting hole For internal cutouts without a lead-in cut from an edge, pre-drill a starting hole 12 mm or more in diameter. Insert the blade into this hole to start your cut. 1 1. Starting hole 001919 B) Plunge cutting You need not bore a starting hole or make a lead-in cut if you carefully do as follows. (1) Tilt the tool up on the front edge of the base with the blade point positioned just above the workpiece sur

ページ10に含まれる内容の要旨

001921 Dust extraction 1 The dust nozzle (accessory) is recommended to perform clean cutting opera- tions. To attach the dust nozzle on the tool, insert the hook of dust nozzle into the hole in the base. The dust nozzle can be installed on either left or right side of the base. 2 1. Dust nozzle 2. Base 001922 001923 Then connect a Makita vacuum cleaner to the dust nozzle. CAUTION: If you try to remove the dust nozzle forcibly, the hook of the dust nozzle can be diminished and removed unintentio

ページ11に含まれる内容の要旨

001924 1. Straight cuts When repeatedly cutting widths of 160 mm or less, use of the rip fence will assure fast, clean, straight cuts. To install, insert the rip fence into the rectan- gular hole on the side of the tool base with the fence guide facing down. Slide the rip fence to the desired cutting width position, then tighten the bolt to secure it. 1 1. Rip fence 001925 3 1 2 1. Bolt 2. Fence guide 3. Hex wrench 001926 2. Circular cuts When cutting circles or arcs of 170 mm or less in radius,

ページ12に含まれる内容の要旨

004446 Guide rail adapter set (accessory) When cutting parallel and uniform width or cutting straight, the use of the guide rail and the guide rail adapter will assure the production of fast and clean cuts. 004447 To install the guide rail adapter, insert the rule bar into the square hole of the base as far as it goes. Secure the bolt with the hex wrench securely. 2 1 1. Bolt 2. Rule bar 004448 Install the guide rail adapter on the rail of the guide rail. Insert the rule bar into the square hole

ページ13に含まれる内容の要旨

001929 Anti-splintering device For splinter-free cuts, the anti-splintering device can be used. To install the anti-splintering device, move the tool base all the way forward and fit it from the back of tool base. When you use the cover plate, install the anti-splintering device onto the cover plate. 1 CAUTION:  The anti-splintering device cannot be used when making bevel cuts. 2 1. Base 2. Anti-splintering device MAINTENANCE CAUTION:  Always be sure that the tool is switched off and unplugged

ページ14に含まれる内容の要旨

Memo 14

ページ15に含まれる内容の要旨

Memo 15

ページ16に含まれる内容の要旨

Makita Corporation Anjo, Aichi, Japan 884426E228


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Makita 2107FK 取扱説明書 ノコギリ 49
2 Makita 2414DB 取扱説明書 ノコギリ 4
3 Makita 2704X1 取扱説明書 ノコギリ 10
4 Makita 2414NB 取扱説明書 ノコギリ 82
5 Makita 4101RH 取扱説明書 ノコギリ 8
6 Makita 24016 取扱説明書 ノコギリ 10
7 Makita 4191DZ 取扱説明書 ノコギリ 1
8 Makita 3706 取扱説明書 ノコギリ 2
9 Makita 4112H 取扱説明書 ノコギリ 4
10 Makita 4191DWA 取扱説明書 ノコギリ 2
11 Makita 2704 取扱説明書 ノコギリ 224
12 Makita 4114 取扱説明書 ノコギリ 1
13 Makita 4200H 取扱説明書 ノコギリ 7
14 Makita 4305T 取扱説明書 ノコギリ 66
15 Makita 4324 取扱説明書 ノコギリ 97
16 Sony XS-L12S 取扱説明書 ノコギリ 8
17 Sony XS-L10S 取扱説明書 ノコギリ 1
18 3Com 3CRWDR200A-75 取扱説明書 ノコギリ 6
19 Agilent Technologies 16193A 取扱説明書 ノコギリ 4
20 Aiphone AP-10M 取扱説明書 ノコギリ 1