ページ1に含まれる内容の要旨
OPERATION & PARTS MANUAL
SideWinder
MODEL SHS62A
CUT-OFF SAW
Revision #0 (06/02/06)
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
ページ2に含まれる内容の要旨
Engine exhaust and some of itsconstituents,andsomedustcreated by power sanding, sawing, grinding, drillingandotherconstructionactivities containschemicalsknowntotheState of California to cause cancer, birth defects and other reproductive harm. Someexamplesofthesechemicalsare: Leadfromlead-basedpaints. Crystallinesilicafrombricks. Cementandothermasonryproducts. Arsenicandchromiumfromchemically treatedlumber. Yourriskfromtheseexposuresvaries, dependingonhowoftenyoudothistype of work.To reduce your
ページ3に含まれる内容の要旨
NOTE PAGE
ページ4に含まれる内容の要旨
SHS62A CUT-OFF SAW — TABLE OF CONTENTS Carburetor Mounting Assembly .........................56-57 STOW — SHS62A CUT-OFF Carburetor Assembly ......................................... 58-59 SAW Crankshaft and Piston Assembly ....................... 60-61 Proposition 65 Warning ............................................. 2 Water Kit Assembly ............................................62-63 Table Of Contents ..................................................... 4 Tools ..........................
ページ5に含まれる内容の要旨
SHS62A CUT-OFF SAW — PARTS ORDERING PROCEDURES When ordering parts, please supply the following information: ❒ ❒ ❒ ❒ ❒ Dealer account number ❒ ❒ ❒ Dealer name and address ❒ ❒ ❒ ❒ ❒ ❒ ❒ Shipping address (if different than billing address) ❒ ❒ ❒ ❒ ❒ Return fax number ❒ ❒ ❒ ❒ ❒ Applicable model number ❒ ❒ ❒ ❒ ❒ Quantity, part number and description of each part ❒ ❒ ❒ ❒ ❒ Specify preferred method of shipment: ✓ FedEx or UPS Ground Note: Unless otherwise indicated by customer, all ✓ FedEx or UPS Sec
ページ6に含まれる内容の要旨
SHS62A CUT-OFF SAW — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! HAZARD SYMBOLS Safety precautions should be followed at all times when operating Lethal Exhaust Gases this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to Engine exhaust gases contain poisonous yourself and others. carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled. This Owner's Manual has been NEVER op
ページ7に含まれる内容の要旨
SHS62A CUT-OFF SAW — SAFETY MESSAGE ALERT SYMBOLS Accidental Starting Respiratory Hazard ALWAYS place the engine ON/OFF switch in the OFF position, when the saw ALWAYS wear approved respiratory protection. is not in use. Over Speed Conditions Sight and Hearing hazard NEVER tamper with the factory settings of the engine governor or settings. Personal injury ALWAYS wear approved eye and hearing and damage to the engine or equipment can protection. result if operating in speed ranges above maximu
ページ8に含まれる内容の要旨
SHS62A CUT-OFF SAW — RULES FOR SAFE OPERATION ■ NEVER touch the hot exhaust manifold, WARNING - Read This Manual muffler or cylinder. Allow these parts to cool Failure to follow instructions in this manual may lead to before servicing the saw. Serious Injury or even Death. This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. The following safety guidelines should always be used when operating the Stow SHS62A Cut-off Saw. ■ High Temp
ページ9に含まれる内容の要旨
SHS62A CUT-OFF SAW — RULES FOR SAFE OPERATION General Safety ■ ALWAYS hold the saw with both hands when the engine is running. Use a firm grip with thumbs and fingers encircling ■ ALWAYS read, understand, and the handles. follow procedures in Operator's ■ ALWAYS keep all parts of the body away from the cutting-off Manual before attempting to operate blades when the engine is running. this equipment. ■ ALWAYS keep the handles dry, clean and free of oil or fuel. ■ ALWAYS carry the saw with the e
ページ10に含まれる内容の要旨
SHS62A CUT-OFF SAW — RULES FOR SAFE OPERATION Diamond Blade Safety ■ NEVER leave the machine unattended while running. ■ Use appropriate steel centered diamond blades ■ NEVER run the engine without the air filter. Severe engine manufactured for use on concrete saws. damage could occur. ■ NEVER wear jewelry or loose fitting clothing that may snag WARNING on the controls or moving parts, this can cause a serious injury. ■ ALWAYS inspect diamond blades before each use. The ■ NEVER operate this sa
ページ11に含まれる内容の要旨
SHS62A CUT-OFF SAW — RULES FOR SAFE OPERATION EMERGENCIES ■ ALWAYS know the location of the nearest fire extinguisher. ■ ALWAYS know the location of the nearest first aid kit. ■ In emergencies always know the location of the nearest phone or keep a phone on the job site. Also know the phone numbers of the nearest ambulance, doctor, and fire department. This information will be invaluable in the case of an emergency. SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (06/02/06) — PAGE 11
ページ12に含まれる内容の要旨
SHS62A CUT-OFF SAW — SPECIFICATIONS Table 1. SHS62A Cut-off Saw Specifications 50 x 33 x18 in. Dimension (Shipping) LxWxH (1270 x 838 x 457 mm) Weight 22.9 lbs. (10.4 kg) Blade Size 14 in. (356 mm) Maximum Cut Depth 5 in. (127 mm) Arbor Size 1 in. (20 mm) Ce utting Arm Reversibl Table 2. SHS62A Power Source Specifications Ed ngine Type Two-Stroke, Single Cylinder, Air coole D) isplacement 3.86 cu. in (63.3 cc. M0 aximum Spindle Speed 5M ,10 RP E0 ngine Speed 1M 0,00 RP I0 dle Speed 2M ,50 RP 29.
ページ13に含まれる内容の要旨
SHS62A CUT-OFF SAW — DECAL PLACEMENT Machine Operation And Safety Decals The SHS62A CUT-OFF SAW is equipped with a number of operation and safety decals (Figure 1). Should any of these decals become unreadable, replacements can be obtained from your dealer. P/N DCL 230 P/N DCL 231 P/N DCL 232 A P/N TBD P/N DCL 161 Figure 1. Safety Decals SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (06/02/06) — PAGE 13
ページ14に含まれる内容の要旨
SHS62A CUT-OFF SAW — CONTROLS & COMPONENTS 2 3 1 4 12 11 9 5 10 8 7 6 Figure 2. SHS62A Cut-off Saw Components 1 Figures 2 and 3 shows the location of the basic controls or components for the Stow Model SHS62A Cut-off Saw. Listed below is a brief explanation of each control or component. 1. Air Filter – Prevents dirt and debris from entering the engine 7. Roller Wheel – Allows for easy free movement of the saw air intake. Check filter periodically and keep cleaned or when cutting on a flat surf
ページ15に含まれる内容の要旨
SHS62A CUT-OFF SAW — CONTROLS & COMPONENTS 14 13 15 16 22 21 20 19 18 17 Figure 3. SHS62A Cut-off Saw Components 2 13. Blade Guard – Covers saw blade. 18. Fuel Filler Cap – Remove this cap to add mixed fuel (requires a 50:1 mixture) to the fuel tank. This saw uses a 14. Front Handle – When lifting or carrying of the saw is 2-stroke engine. Make sure fuel cap is tightened securely. required, use this handle. DO NOT over fill. See Figure 25 for correct fuel to oil mixture. 15. Throttle Lock Leve
ページ16に含まれる内容の要旨
SHS62A CUT-OFF SAW — BLADE INSTALLATION INSTRUCTIONS The Stow Side Winder Cut-Off Saw comes with a Tool Kit (Figure 4) that assists you with day to day operations. You will need these tools for the assembly of your saw. is a versatile screwdriver/wrench that accommodates Item common bolt/screw and nut head sizes of your saw. Item is the wrench necessary to accommodate various allen screws. Figure 4. Tool Kit Blade Installation Procedure STEP 1 STEP 3 Chose the proper blade arbor side
ページ17に含まれる内容の要旨
SHS62A CUT-OFF SAW — WATER KIT INSTALLATION INSTRUCTIONS Contents of Water Kit The contents of the Water Kit cannot be purchased seperately. See Water Kit Assembly in Parts Section of this manual for Water Kit part number. Hose Clamp Socket Head Cap Screw w/ Washer Quick Disconnect Fitting Water Hose Hex Key Tool (Included with Tool Kit) Figure 9. Water Kit Parts Plastic Ties Wet Air Filter Canister (Sold Seperately) Water Kit Installation Procedure Connect the Quick Disconnect F
ページ18に含まれる内容の要旨
SHS62A CUT-OFF SAW — BLADES PREPARATION / PRE-INSPECTION 1. Read and fully understand this manual, the safety instructions in particular, and the engine manufacturer's manual supplied with the saw. 2. Select the correct blade for each application. If abrasive blades are used, MAKE CERTAIN they are designed for use on a concrete floor saw. They must be reinforced and have a hole for the driving pin. When wet cutting with an abrasive blade, MAKE CERTAIN the blade is intended for Figure 12. D
ページ19に含まれる内容の要旨
SHS62A CUT-OFF SAW — INITIAL START-UP/OPERATION INITIAL START-UP CAUTION DO NOT attempt to operate the saw until the Safety, General Information and Inspection sections of this manual have been read and thoroughly understood. Depending on engine manufacturer, operating steps may vary. See engine manufactures operating manual. CAUTION Figure 13. Fuel to Oil Mixture NEVER operate the saw in a confined area For correct fuel to oil mixture, add 2.6 fl. oz or enclosed area structure that does not
ページ20に含まれる内容の要旨
SHS62A CUT-OFF SAW — INITIAL START-UP/OPERATION 7. Grasp the starter grip and slowly pull it out. The resistance becomes the hardest at a certain position, corresponding to Mark the cutting line clearly and always NOTE the compression point. Pull the starter grip briskly and smoothly saw in a STRAIGHT LINE ONLY. for starting. 8. If the engine has started, slowly return the choke lever to the "OPEN" position. If the engine has not started repeat steps 1 through 9. 4. When the end of the cut h
