ページ1に含まれる内容の要旨
Network ScanGear
User’s Guide
Please read this guide before operating this equipment.
After you finish reading this guide, store it in a safe place for future reference. ENG
ページ2に含まれる内容の要旨
Organization of this User’s Guide Chap 1 Introduction 1 Chap 2 Installation 2 Chap 3 Before Scanning 3 Chap 4 Scanning 4 Index • The contents of this manual are subject to change without prior notification. • Although every effort is given to the production of this manual, please notify any errors or omissions you should notice. • The contents of this manual may not be reproduced without permission.
ページ3に含まれる内容の要旨
Table of Contents How to Use This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv Symbols Used in This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv About Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv About Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Chapter1 Introduction Introduction
ページ4に含まれる内容の要旨
Chapter4 Scanning Scanning from the Platen Glass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Scanning from the Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Scanning from the Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Ensuring Scanned Originals are Correctly Oriented . . . . . . . . . . . . . . . . 4-6 Scanning Different Sized Originals Together . . . . . . . . . . . . . . . . . . . .
ページ5に含まれる内容の要旨
How to Use This Manual Symbols Used in This Manual In this manual the following headings are used to mark important notes. IMPORTANT • This indicates an important item or restriction that must be observed during operation. Read carefully to avoid failure or damage to the unit. NOTE • This gives reference material or supplementary information about operation. Reading is recommended. About Abbreviations The following abbreviations are used in this manual. ® ®
ページ6に含まれる内容の要旨
About Trademarks Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation in the United States and/or other countries. IBM and IBM PC/AT are trademarks of International Business Machines Corporation. Other company names and product names referred to in this manual are trademarks or registered trademarks of the respective companies. About Trademarks v
ページ7に含まれる内容の要旨
ページ8に含まれる内容の要旨
Introduction 1 CHAPTER This chapter gives basic information required in order to use Network ScanGear. Introduction to the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2 Readme File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ9に含まれる内容の要旨
Introduction to the Software 1 Features Network ScanGear is a 32-bit TWAIN-compliant scanner driver that allows computers on a network to use a Canon imageRUNNER series digital copier that is located in the same subnet as a scanner. It consists of the following software. n ScanGear Tool This software is installed together with the Network ScanGear driver, and enables the user to select the device name of the scanner on the network to be used for scanning with the Network Sc
ページ10に含まれる内容の要旨
NetworkScanGear.book Page 3 Monday, July 1, 2002 3:01 PM Operating Environment Network ScanGear requires the following operating environment. 1 Hardware • IBM PC/AT or compatible computer running Windows 95/98/Me/NT4.0/2000/XP • At least 100 MB of available hard disk space (recommended) NOTE • Space equal to at least twice the size of the scanned image on the hard disk is required. • Main memory must meet the following conditions: For Windows 95/98/Me: at least 16 MB (32 MB or
ページ11に含まれる内容の要旨
Software Network ScanGear runs under one of the following operating systems. ® ® • Microsoft Windows 95 ® ® • Microsoft Windows 98 ® ® • Microsoft Windows Millennium Edition 1 ® ® • Microsoft Windows NT Version 4.0 (Service Pack 3 or later) ® ® • Microsoft Windows 2000 ® ® • Microsoft Windows XP IMPORTANT • Windows Socket 2 must be installed in order to use Network ScanGear under Windows 95. For details, refer to the readme.txt file. Scanning with Network ScanGe
ページ12に含まれる内容の要旨
Installation 2 CHAPTER This chapter explains how to install Network ScanGear. Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2 Uninstallation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5 2-1
ページ13に含まれる内容の要旨
Installation Procedure Follow the procedure below to install Network ScanGear. This installs the ScanGear Tool and the Network ScanGear driver at the same time. IMPORTANT 2 • If an older version of Network ScanGear is installed on your computer, uninstall it before installing the new version. For instructions, see ‘Uninstallation Procedure,’ on p.2-5. 1 Start Windows. IMPORTANT • When installing under Windows NT4.0/2000/XP, you must log on as an Administrator. 2 Insert the Network ScanGe
ページ14に含まれる内容の要旨
9 In the Choose Destination Location dialog box, specify the location where Network ScanGear is to be installed, then click the Next button. 2 10 Specify the folder to which the Network ScanGear program icon is to be added, then click the Next button. Installation Procedure 2-3 Installation
ページ15に含まれる内容の要旨
11 Check the settings in the Start Copying Files dialog box, then click the Next button. 2 Installation starts, and the progress of installation is displayed. When the necessary files have been copied, a dialog box appears to indicate that installation has been completed. 12 Click the Finish button. NOTE • When installation is complete, before starting Network ScanGear you must use the ScanGear Tool to select the network scanner to be used for scanning. For details see ‘Selecting the Network
ページ16に含まれる内容の要旨
Uninstallation Procedure Follow the procedure below to uninstall Network ScanGear. 2 1 Click the Start button, and select Programs – Network ScanGear – n.n – Uninstallshield. (“n.n” is the version name. For example, “1.0” appears for version 1.0.) 2 In the Confirm File Deletion dialog box, click the OK button. This deletes the files and completes the uninstallation. Uninstallation Procedure 2-5 Installation
ページ17に含まれる内容の要旨
ページ18に含まれる内容の要旨
Before Scanning 3 CHAPTER This chapter describes preparations required to scan using Network ScanGear, the procedure for starting Network ScanGear, and the Network ScanGear Main Window. Switching the Scanner Online and Offline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2 Switching the Scanner Online . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2 Switching Offline . . . . . . . . . . . . . . . . . . . . . . .
ページ19に含まれる内容の要旨
Switching the Scanner Online and Offline To start Network ScanGear for scanning, first you must switch the scanner online. Switching the Scanner Online Switching the scanner online enables communications with other devices on the network, and allows the scanner to receive data from the computer. 3 Follow the procedure below to switch the scanner online. 1 On the scanner operating panel or touch panel display, press the Options. When the Options key is on the operating panel Pr
ページ20に含まれる内容の要旨
2 Press Online. When the Options key is on the operating panel 3 When the following display appears, the scanner is online. When the Options key is on the touch panel display Switching the Scanner Online and Offline 3-3 l l Before Scanning
