ページ1に含まれる内容の要旨
C150-E100-01EN
M3097DE/DG Image Scanner
Operator's Guide
ページ2に含まれる内容の要旨
M3097DE/DG Image Scanner Operator's Guide
ページ3に含まれる内容の要旨
Edition Date published Revised contents 01 December, 1997 First edition Specification No. C150-E101-01EN This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not ins
ページ4に含まれる内容の要旨
Please send your comments on this manual or on Fujitsu products to the following addresses: FUJITSU COMPUTER PRODUCTS OF FUJITSU FRANCE S.A. AMERICA,INC. Bâtiment Aristote,17 rue Olof palme 2904 Orchard Parkway,San Jose. 94006 Créteil cedex,FRANCE California 95134-2022,U.S.A. TEL:33-14-513-1616 TEL:1-408-432-6333 FAX:33-14-399-0700 FAX:1-408-432-3908 Home page:http://www.fcpa.com/ FUJITSU HONG KONG Limited Room 2521,Sum Hung Kai Centre FUJITSU AUSTRALIA LIMITED 30 Harbour Road Wanchal,Hong Kong
ページ5に含まれる内容の要旨
IMPORTANT NOTE TO USERS READ CAREFULLY ALL OF THIS MANUAL BEFORE USING THIS PRODUCT. IF NOT USED CORRECTLY, UNEXPECTED DAMAGES MAY BE CAUSED TO THE USERS OR THE BYSTANDERS. While all efforts have been made to ensure the accuracy of all information in this manual, FUJITSU assumes no liability to any party for any damage caused by errors or omissions or by statements of any kind in this manual, its updates or supplements, whether such errors are omissions or statements resulting from negligence, a
ページ6に含まれる内容の要旨
Preface This manual explains how to use the M3097DE/DG image scanner. This manual contains COMPONENTS, INSTALLATION AND CONNEC- TION, OPERATING INSTRUCTION,DOCUMENT SPECIFICATION, SPECFICATIONS and SETUP MODE. Refer to “Cleaning and Maintenance” for the information about the routine operation of the M3097DE/DG. Reference Guide contains OPERATING INSTRUCTION, CLEANING, REPLACEMENT OF PARTS, ADJUSTMENT and TROUBLESHOOTING. The M3097DE/DG is very fast and highly functional image scanner devel- oped
ページ7に含まれる内容の要旨
Conventions Special information, such as warnings, cautions are indicated as follows: WARNING WARNING indicates that personal injury may result if you do not follow a procedure correctly. CAUTION CAUTION indicates that damage to the scanner may result if you do not follow a procedure correctly. The following symbols are used in this manual. Used for general WARNING and CAUTION. Be careful not to pinch your fingers or hands. v
ページ8に含まれる内容の要旨
vi
ページ9に含まれる内容の要旨
CONTENTS q CHAPTER 1 COMPONENTS Checking the Components ........................................................1-1 Units and Assemblies ................................................................1-2 Operator Panel ..........................................................................1-5 q CHAPTER 2 INSTALLATION AND CONNECTIONS Precautions................................................................................2-1 Inspection .......................................................
ページ10に含まれる内容の要旨
viii
ページ11に含まれる内容の要旨
COMPONENTS COMPONENTS INSTALLATION AND CONNECTIONS INSTALLATION AND CONNECTIONS OPERATING INSTRUCTION OPERATING INSTRUCTION DOCUMENT SPECIFICATION DOCUMENT SPECIFICATION SPECIFICATIONS SPECIFICATIONS SETUP MODE SETUP MODE GLOSSARY OF TERMS GLOSSARY OF TERMS INDEX INDEX ix ix
ページ12に含まれる内容の要旨
CHAPTER 1 COMPONENTS After unpacking the scanner,confirm that all the components have been received. This chapter describes the components of the scanner, part names, and operator panel arrangement and their function. Checking the Components Units and Assemblies Operator Panel
ページ13に含まれる内容の要旨
1 Cheking the Components These high precision components must be handled with care. Confirm that all the components shown in the following figure have been received. If any component is missing, please contact your sales agent. Scanner Terminator Power cable Power cable (for M3097DG) for North America for Europe or Operator's Guide (this manual) and Cleaning and Maintenance Pad ASY 1-1
ページ14に含まれる内容の要旨
Units and Assemblies This section shows the exterior view and assemblies of the scanner. This section also provides names of each part and describes their functions. Units qDocument cover rAutomatic document eDocument feeder(ADF) holding pad wDocument bed tStacker uOperator panel oADF lever iADF paper chute !2Third party slot yPower switch !1Interface connectors !0Power inlet !3Memory cover M3097DE 1-2
ページ15に含まれる内容の要旨
oADF lever iADF paper chute yPower switch !1Interface connectors !3Memory cover !0Power inlet M3097DG No. Function q Document cover: Closed over and holds a document to be read. w Document bed: A document to be read is placed on the bed also called Flatbed (FB). e Document holding pad: Presses a document to the document bed. r Automatic document feeder (ADF): Automatically feeds documents to the reading position. t Stacker: Stacks the read documents. y Power switch: Turns the power on or off. u
ページ16に含まれる内容の要旨
Assemblies Thumb screw Guide A ASY Bearing Stacker Pick roller 2 Pad ASY Bearing Pick roller 1 1-4
ページ17に含まれる内容の要旨
Operator Panel The operator panel is located at the upper right hand side of the scanner. The panel consists of an LCD (24 character x 2 line), LEDs and buttons. Arrangement Operator panel ( ) ( ) (STOP) Previous Next Exit (START) READ ENTER CHECK 1-5
ページ18に含まれる内容の要旨
/ Button LED Function Name of the button Function and LED Button Next LCD displays the next screen. Previous LCD displays the Previous screen. ← Moves the cursor to the left → Moves the cursor to the right Exit • When “CHECK” LED lights, pressing this button releases error status (turn off “CHECK” and returns to “Scanner Readry” screen). • When you are setting on the operator panel, pressing this button returns to “Scanner Ready” screen immediately. ENTER The parameter selected by cursor become
ページ19に含まれる内容の要旨
Counter Display The scanner is provided with the counter display. Paper counter Abrasion counter Counter Function Paper counter Paper counter counts the scanned sheet from the start of reading to Paper Empty or an error detection. So this counter is automatically reset at the start of reading. Abrasion counter Abrasion counter counts the accumulated number of the scanned sheet. This counter increments at every 10 sheets. This counter is useful to check the cleaning cycle or parts replacement cy
ページ20に含まれる内容の要旨
Operation status Operation status is indicated by the following message: Scanner displays followig screen when waiting Start button pressed. (Only M3097DE) When the Pick roller cleaning is necessary, the scanner displays as follows on the upper line. When the ADF glass cleaning is necessary, the scanner displays as follows on the LCD. Clean the Pick roller or ADF glass in accordance with the manual, “Cleaning and Maintenance”. 1-8
