ページ1に含まれる内容の要旨
Megapixel (PoE) Cube Network Camera
CB-100A/CB-101A/CB-102A Series
User’s Manual
Quality Service Group
ページ2に含まれる内容の要旨
Product name: Network Camera (CB-100A/CB-101A/CB-102A series) Release Date: 2010/11 Manual Revision: V1.0 Web site: www.brickcom.com Email: technical@brickcom.com info@brickcom.com © 2010 Brickcom Corporation. All Rights Reserved - -
ページ3に含まれる内容の要旨
Table of Contents Before You Use This Product .......................................................................................... 0 FCC Warning .................................................................................................................. 0 Regulatory Information .................................................................................................... 1 Package Contents .................................................................................
ページ4に含まれる内容の要旨
PIR(*) ............................................................................................................... 61 Audio Detection ............................................................................................... 61 Notifications ............................................................................................................ 62 FTP Settings .................................................................................................... 62 E-mail Setti
ページ5に含まれる内容の要旨
Before You Use This Product In many countries, there are laws prohibiting or restricting the use of surveillance devices. This Network Camera is a high-performance, web-ready camera which can be part of a flexible surveillance system. It is the user’s responsibility to ensure that the operation of this camera is legal before installing this unit for its intended use. Upon opening the product’s package, verify that all the accessories listed on the “Package Contents” are included. Bef
ページ6に含まれる内容の要旨
Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful i
ページ7に含まれる内容の要旨
Package Contents Please check to make sure the product package contains all the accessories listed below. a. Network Camera b. Product CD CB-100A/CB-101A CB-102A c. Camera Stand d. Warranty C ard CB-100A/CB-101A CB-102A e. Terminal I/O Connector Block f. Easy Installation Guide g. 1.5m White Flat RJ-45 cable h. Power Adapter(CB-100A) (CB-100A)
ページ8に含まれる内容の要旨
Cube Network Camera Overview The compact Brickcom (PoE) Cube network camera series offers a high quality, video TM surveillance solution for residences and small businesses. EasyLink is a feature of the (PoE) Cube series which allows for users to simply plug in the camera to any home or small business network and play the video. This camera series offers a user-friendly and unique design which allows anyone without a technical background to use it. It features live video feed and tw
ページ9に含まれる内容の要旨
Small Office Surveillance – Security systems for small offices can be expensive and difficult to install and maintain. With the EasyConfig software, the (PoE) Cube series can easily be installed and configured by anyone without extensive technical knowledge. The video can be reviewed remotely so business owners can monitor office safety and employee productivity at all times. Residence monitor – Home owners worry about their house and property when they are away. The (PoE) Cube
ページ10に含まれる内容の要旨
- 3 -
ページ11に含まれる内容の要旨
Device Appearance Description < Front & Rear view > Adjustable Focal Lens Built-in Microphone PIR(*) Illumination LED(*) Speaker(*) Ethernet RJ45 Terminal I/O Connector 10/100 Socket Reset Button Reset Button Power Connector - 4 -
ページ12に含まれる内容の要旨
Power LED Micro SD slot(*) Status LED Internet LED WPS button WPS LED (WCB-100A) (WCB-100A Only) Firmware upgrade LED Privacy button(*) (CB-100A/CB-101A/CB-102A) Privacy LED NOTE - The WPS and Privacy buttons must first be enabled through the web GUI in order to work. See page 41 for details on how to enable the Privacy button. 1. (*) These are optional features. Please refer to the Product List for the full list of optional features available for the prod
ページ13に含まれる内容の要旨
LED Behavior Function LED Behavior Description Remark Power Continuous Illumination Normal Operation Top (Blue) Power Unlit Powered off Top (Blue) 1. Connected to switch by Status Continuous Illumination Ethernet or WiFi. Second (Blue) 2. Reset to default. 1. Powered off Status Unlit Second (Blue) 2. No connection Status 1. Upgrading F/W 2. Performing site survey Second (Blue) 1. .Connecting to the Blinking network Second (Blue) Status 2. Restoring settings. Continuous
ページ14に含まれる内容の要旨
Hardware Reset Reset Button The Reset Button can be used to reboot the camera or restore it to factory default settings. If the camera experiences a problem, rebooting the camera may correct the problem. If the problem remains, please restore the camera to factory default settings and reinstall the software. To Reboot - Press and hold the Reset Button for one second using a paper clip or thin object. Wait for the camera to reboot. To Restore – Press and hold the Reset Button
ページ15に含まれる内容の要旨
Installation System Requirements Operating System: Microsoft Windows XP Home Edition SP2 Microsoft Windows XP Professional SP2 Computer: IBM PC/AT Compatible CPU: Pentium 3GHz or faster Memory: 1024 MB or more Monitor: 1024 x 768 pixels or more, 24-bit True color or better Network Interface: 10/100Mbps Network interface card must be installed Web Browser: Microsoft Internet Explorer 6.0 SP2 or higher Adobe Reader: Adobe Reader 8.0 or higher Audio: The audio func
ページ16に含まれる内容の要旨
Camera Connection 1 Connect the supplied power cable from the camera to the power outlet. 2 Connect the camera to a switch via Ethernet cable. 3 Terminal I/O Connector Block Connection 3.1 The supplied terminal I/O connector block can be used to connect external devices, such as sensors and alarms to the camera. Use the diagram above to attach the external devices to the connector block. Attach the connector block to the terminal - 9 -
ページ17に含まれる内容の要旨
connector on the camera. 2 Basic Connection (Without PoE) 2.1 Connect the camera to a switch using a standard Ethernet cable. 2.2 Connect the power adapter from the camera to a power outlet. Note: DC12V 1A power adapter is required. 3 Power over Ethernet (PoE) Connection 3.1 The CB-101A is PoE compliant, so there are two options for connecting the camera to a power and Ethernet source. The camera can either be connected to a PoE-enabled switch or a non-PoE switch. A. If using
ページ18に含まれる内容の要旨
5. Use a standard Ethernet cable to connect the camera to a PoE Injector. 6. Use a standard Ethernet cable to connect the PoE Injector to the non-PoE switch. 7. Use a standard power cable to connect the PoE Injector to a power outlet. - 11 -
ページ19に含まれる内容の要旨
Software Installation In this manual, "User" refers to whoever has access to the Network Camera, and "Administrator" refers to the person who can configure the camera and grant user access to the camera. After checking the hardware connection, run the Installation Wizard program included on the product’s CDROM to automatically search the intranet for the camera. There may be many cameras on the local network. Differentiate the cameras using the serial number which is printed on the la
ページ20に含まれる内容の要旨
2. In the Install Shield Wizard dialog box, click to continue. 3. Read the End-User License Agreement and check the option “I accept the terms of the license agreement”. Click to continue. - 13 -
