ページ1に含まれる内容の要旨
EAN900
User’s Manual
Copyright © EverFocus Electronics Corp,
Release: Dec. 2009 Rev.D
ページ2に含まれる内容の要旨
EAN900 Product Name: EAN900 EverFocus IP Network Cameras Model Number(s): EAN900 FCC Notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential Installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used i
ページ3に含まれる内容の要旨
EAN900 About this document All the safety and operating instructions should be read and followed before the unit is operated. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. Safety Notice -These limits are designed to provide reasonable protection. This equipment generates, uses and
ページ4に含まれる内容の要旨
EAN900 Do not operate the appliance beyond its specified temperature, humidity or power source ratings. Do not use the appliance in an extreme environment where high temperature or high humidity exists. Use the appliance at temperature within 0℃ ~ +40℃ / 32 ~ 104 and a humidity below 90%. The input power source for this appliance is 12 VDC & PoE. Use only the recommended power supplies. Power supplies must comply with the requirement of the latest version of IEC60950-1. Substitu
ページ5に含まれる内容の要旨
EAN900 TABLE OF CONTENTS 1. INTRODUCTION....................................................................................................6 2. FEATURES ..............................................................................................................6 3. ACCESSING THE CAMERA MENU ...................................................................6 4. SETTING................................................................................................................10 4.
ページ6に含まれる内容の要旨
EAN900 1. INTRODUCTION The EAN900 network camera with a built-in 1.3 mega-pixel progressive scan CMOS offers crisp images with sharp definition and reduced motion blur that occurs in regular interlaced CCD. EAN900 process multi-streaming of H.264 or MPEG-4, MJPEG compression in full megapixel resolution, which allows for optimization both in image quality and bandwidth efficiency. Equipped with a SD card slot, EAN900 offers another way to record and manage your video and can provide uni
ページ7に含まれる内容の要旨
EAN900 camera video. Please click "Yes". Step 6. Congratulation!! You should be able to see the live image now. 13 14 1 2 3 4 5 6 7 8 9 10 11 12 1. Press button to display the "Live" page. Double click on the image to show a full screen display, double click again or press ESC to return normal display. 2. Press button to enter Setting page. In Setting page, there are 8 sections: [System Info], [User Config], [Network], [Video], [Audio], [User], [Event] and
ページ8に含まれる内容の要旨
EAN900 5. View Size You can select View size to either reduce or enlarge the image to the appropriate view size. Select the view size for live images from: 1280*1024/1280*960/1280*720/640*480/320*240 6. Digital Zoom Press “+” or “-“ button to enlarge / reduce the displayed image. (max. is X10) 7. Record The record button is used to record the current video stream. The location where the image file is saved can be specified in Setting -> User’s Config. Please refer to
ページ9に含まれる内容の要旨
EAN900 11. Manual Control – Trigger Event Press “Trigger Event” button to trigger an event directly from live view page, and event actions will be effective if they have been set in “Event” menu. (Please refer to “4.7.1 Event”) 12. Manual Control – Reset Alarm Press “Reset Alarm” button to reset alarm output remotely. 13. Status Display The name of the camera whose settings currently being configured, current date/time and current frame rate will be displayed. 14. Event s
ページ10に含まれる内容の要旨
EAN900 4. SETTING Click this button to display the setup menu. 10
ページ11に含まれる内容の要旨
EAN900 4.1 System Info System information and system log check of the setup menu can be performed on this page. The “System Info” page has 2 tabs: [Information] tab and the [Log] tab. 4.1.1 Information System Information: Firmware version, MAC address, Video Type, Model number. (unchangeable, for reference only) 11
ページ12に含まれる内容の要旨
EAN900 4.1.2 Log System Log: Date/Time: displaying date and time of the log. Log message: all information and event message, including login, user’s IP, reboot, firmware upgrade, load factory default, configuration reset and event detected. System will keep the newest 256 records. Press button to export system log into “.txt” file and select the location where the exported log file will be saved to. 12
ページ13に含まれる内容の要旨
EAN900 4.2 User Config Live view configuration is to be set by user. Each login user can make his/her own settings for the following items: Text Setting Check the box for text of Machine name, Date/Time or Frame Rate to be displayed on the screen. Text Color Foreground Color: Select the foreground color of text to be displayed by moving the slide bar between Red, Green and Blue until your desire color is obtained. Position: Select the position where the text will be dis
ページ14に含まれる内容の要旨
EAN900 Time Format: 24 Hours or 12 Hours. Press Apply to apply the setting changes or Reset to reset without saving the change. Recording/Snapshot Export Setting Enable Event Recording to PC: Allow event video recorded to users' PC if any events have been set to record to PC. Export folder: Select Export folder by clicking on button, then direct to the folder to be exported. File size: Able to limit the size of the single recording file in minutes. When the single recordi
ページ15に含まれる内容の要旨
EAN900 change. 4.3 Network The network settings and the settings relating to Network, DDNS, Bandwidth, SMTP/FTP and Network Alarm can be configured on this page. The "Network setup" page has 5 tabs of the [Network] tab, the [DDNS] tab, the [SMTP/FTP] tab and the [Network Alarm] tab. 4.3.1 Network The following information is required to configure the network settings. Contact the network administrator or your Internet service provider. • IP Type • IP address • Subnet mask • Ga
ページ16に含まれる内容の要旨
EAN900 DHCP: Configure the DHCP server not to assign the same IP addresses used for the other network cameras and PCs whose IP address is unique. Refer to the network administrator for the settings of the server. Default: DHCP. Static IP: User can manually set the static IP for network connection. PPPoE: This is a DSL connection application, ISP will ask user to input user name and password. Note: If PPPoE is used as IP type, IP Utility software will not be able to detect the
ページ17に含まれる内容の要旨
EAN900 Press Apply to apply the setting changes or Reset to reset without saving the change. Port Setting HTTP Port Port number for HTTP/WEB communication. Press Apply to apply the setting changes or Reset to reset without saving the change. 4.3.2 DDNS DDNS setting When accessing the camera via the Internet from the network environment of which the global IP address is obtained using DHCP, the DDNS function is necessary. To use the DDNS function, it is necessary to
ページ18に含まれる内容の要旨
EAN900 ○ www.sitelutions.com ○ www.dyndns.com ○ www.no-ip.com Enable: Check the box to enable DDNS setting. Service ISP: If you choose EverFocus DDNS server, you can obtain a free account name from EverFocus ”www.everfocusddns.com”. Enter an IP Cam Account Name: .everfocusddns.com Press button to register or update DDNS account. If you wish to get a domain name from other DDNS provider, it is necessary to configure Record ID, FQDN, Username and password and regi
ページ19に含まれる内容の要旨
EAN900 network. This is a useful function when connecting the camera to busy or heavily loaded networks. The default setting is Unlimited. Max. Client Limit: enter a value here to restrict the number of clients accessing the camera. This is useful if you need to save on bandwidth. Up to 32 clients is allowed to see live video simultaneously. Subsequent viewers will see a blank image. Press Apply to apply the setting changes or Reset to reset without saving the change. 4.3.4 S
ページ20に含まれる内容の要旨
EAN900 Authentication: Check the box, if the SMTP server requires Authentication (user/ password). User name: Input the login user ID if the SMTP server requires Authentication. Password: Input the password if the SMTP server requires authentication. Receiver Address: Input the e-mail address for receiving e-mail message when the EVENT is enabled and triggered. Please use “;” to separate address. Sender Address: Input sender’s e-mail address, so that receiver can recognize the
