ページ1に含まれる内容の要旨
Monochrome Double Speed Camera
CV-M30
Operation Manual
Camera: Revision D
Manual: Version 1.0
CV-M30manDMay12.doc
JPT 12-05-03
ページ2に含まれる内容の要旨
CV-M30 Table of Contents 1. General ........................................................................................................2 2. Standard Composition ......................................................................................2 3. Main Features ................................................................................................2 4. Locations and Functions ...................................................................................3 5. Pin Assi
ページ3に含まれる内容の要旨
CV-M30 1. General The CV-M30 camera revision D is an updated version with a new CCD sensor ICX-418ALL-6 with improved specifications. The revision D camera can only operate in double speed. CV-M30 is a monochrome CCD video camera designed for industrial video sensing applications. The camera operates with double speed scanning, where the horizontal and vertical frequencies is doubled compared to a standard camera. The image-capturing speed is the double. The CV-M30 also offers an attrac
ページ4に含まれる内容の要旨
CV-M30 4. Locations and Functions Fig. 1. Locations 1. 1/2” interline-transfer type CCD sensor 2. Lens mount for C-mount lenses. *1) 3. BNC connector for video output 4. Switch block SW1 for shutter speed and function mode setting 5. 6-Pin connector for Input/output of control signals 6. 12-Pin connector for 12V DC power and external sync signals 7. Gain potentiometer for manual gain adjustment 8. Screw holes for Tripod mo
ページ5に含まれる内容の要旨
CV-M30 5. Pin Assignment 5.1. 12-pin Multi-connector (DC-IN/VIDEO OUT, EXT.HD/VD IN) Type: HR10A-10R-12PB-01 (Hirose) male Seen from rear. Pin no Signal Remarks 1 GND 2 +12 V DC input 3 GND Parallel with the BNC connector. *1) 4 Video output 5 GND 1 9 6 HD input 2 8 10 Parallel with pin 5 on 6 pin con. *2) 7 VD/trig input 11 3 12 7 8 GND Parallel with pin 2 on 6 pin con. 4 6 9 EEN output 5 10 GND 11 +12 V DC input 12 GND Notes: Fig. 2.
ページ6に含まれる内容の要旨
CV-M30 5.3. Input and Output Diagram Fig. 4. WEN and EEN output Fig. 5. HD and VD/Trigger input - 5 -
ページ7に含まれる内容の要旨
CV-M30 6. Functions and Operations 6.1. Input of External HD/VD Signals As factory setting the camera can be synchronized by external HD/VD signals. The external supplied HD/VD signal should follow the same standard as the camera setting for speed, scanning and interlace. The signal level must be 4.0 Vp-p ±2.0V with 75 Ohm termination on. The termination can be switched off with the internal switch SW1 on the PK8212 board. The VD input terminal is used for external trigger signal i
ページ8に含まれる内容の要旨
CV-M30 6.3.1. Edge Pre-select Mode The edge pre-select mode will work in non-interlaced and field accumulation mode with partial scanning and double speed. The CV-M30 starts the exposure (= accumulation of photoelectric charge) at the first HD pulse after the falling edge of the ext. trigger pulse. The exposure ends after the time set by the 3 shutter switches SW1-1 to SW1-3. The accumulated signal will be read out as a single field before a new trigger can be applied. The interval between
ページ9に含まれる内容の要旨
CV-M30 6.3.2. Pulse Width Control Mode The pulse width control mode will only work in non-interlaced field accumulation mode. The exposure is controlled by the low period of the ext. trigger pulse. The CV-M30 starts the exposure at the first HD pulse after the falling edge of the ext. trigger pulse. The exposure ends at the first HD pulse after the rising edge of the ext. trigger. The Shutter can be controlled to be within the range from >1H (>32 usec.) to <1000H. The AC coupling causes
ページ10に含まれる内容の要旨
CV-M30 6.4. Other Functions 6.4.1. Double Speed Mode The CV-M30 camera revision D operates only with double speed scanning. Double speed is 120 fields per second. (V= 119.88Hz. H=31.468 kHz). To use this mode. Set: 6.4.2. Partial Scanning Mode To obtain a higher frame rate, the partial scanning can be used. In this mode only the vertical center part of the CCD sensor is read out. Partial scan will only work in non-interlaced mode. The useable image format is Full non
ページ11に含まれる内容の要旨
CV-M30 6.5.2. External Sync Mode H = 31.778 µs Fig. 10. Vertical timing with external sync 6.5.3. External Sync Mode. Partial Scan H = 31.778 µs H = 31.778 µs Fig. 11. Partial scanning vertical timing with external sync - 10 -
ページ12に含まれる内容の要旨
CV-M30 6.5.4. Edge Pre-select H = 31.778 µs Fig. 12. Vertical timing for Edge pre-select 6.5.5. Edge Pre-select. Partial Scan H = 31.778 µs Fig. 13. Vertical timing for Edge pre-select 1/2 partial scanning H = 31.778 µs Fig. 14. Vertical timing for Edge pre-select 1/3 partial scanning - 11 -
ページ13に含まれる内容の要旨
CV-M30 6.5.6. Pulse Width Control H = 31.778 µs Fig. 15. Vertical timing for pulse width control 6.5.7. Pulse Width. Partial Scan H = 31.778 µs Fig. 16. Vertical timing for pulse width control 1/2 partial scanning H = 31.778 µs Fig. 17. Vertical timing for pulse width control 1/3 partial scanning - 12 -
ページ14に含まれる内容の要旨
CV-M30 7. Mode Setting 7.1. Switch SW1 on Rear Panel 7.1.1. SW1 Lay-out OFF = < ON = > SW 1 OFF ON < < < < > > > > 1 < < > > < < > > SHUTTER 2 < > < > < > < > 3 SCAN mode 1 4 < < > > 5 SCAN mode 2 6 < > < > External TRIGGER 7 Normal < > 8 < > GAIN MAN AGC Fig. 18. Switch settings for switch on rear 7.1.2. Table for SW1 Setting Switch Switch function Mode setting no. OFF ON 1 Shutter data MSB For shutter speed select. 2 Shutter data Refer to shutter table
ページ15に含まれる内容の要旨
CV-M30 7.1.4. Scan Mode Settings With SW1-4 and SW1-6 the scanning mode can be selected. The table shows the modes. SW1-4 SW1-6 Function Mode Remarks OFF OFF 2:1 Interlaced mode In Normal trigger mode only. (Continuous). ON OFF 1/2 partial scan Non-interlaced only OFF ON Non-interlaced mode ON ON 1/3 partial scan Non-interlaced only For detail, please refer to “6.2. Continuous Operation.” and “6.4.2. Partial Scanning Mode.” 7.1.5. Double Speed Mode Vertical frequency 119
ページ16に含まれる内容の要旨
CV-M30 7.2. Internal Switch and Jumper Settings Inside the camera there are switches for 75 termination of external trigger/VD and HD and for trigger mode select. There are also jumpers for gamma select. 7.2.1. Trigger/VD and HD Termination On the PK8212 board switch SW1 for 75 Ohm termination of external trigger/VD and HD is found. SW1-1 is for external HD termination. SW1-2 is for external trigger or external VD termination. ON is 75 Ohm termination. It is factory setting. OFF
ページ17に含まれる内容の要旨
CV-M30 8. Internal Adjustments of Video Signal For adjustment of the video output signal there are internal potentiometers on th PK 7987A board. Adjustment should only be done in a setup with a standard test chart and controlled illumination Do not touch these potentiometers unless you are familiar with camera adjustments. VR 1 is for AGC level setting. Factory setting is 700 mVpp ±30 mV VR2 is for black level set-up. Factory setting is 20 mVpp ±2 mV VR3 is for white clip level.
ページ18に含まれる内容の要旨
CV-M30 9. External Appearance and Dimensions Fig. 22. Outline - 17 -
ページ19に含まれる内容の要旨
CV-M30 10. Specifications 10.1. Specification table Model CV-M30 CCD Sensor 1/2”Monochrome IT CCD. Sony ICX-418ALL-6 Image Area 6.45mm (H) x 4.84mm (V) Effective Pixels 768(H) x 494(V) Cell Size 8.4 µ m(H) x 9.8 µm(V) Pixels in video output Double Speed 2:1 interlaced 756(h) x 485(v) 60 frames/sec Non-interlaced 756(h) x 242(v) 120 field/sec 1/2 partial 756(h) x 111(v) 240 fields/sec 1/3 partial 756(h) x 67(v) 360 fields/sec Vertical Frequency Double speed
ページ20に含まれる内容の要旨
CV-M30 11. Appendix 11.1. Precautions Personnel not trained in dealing with similar electronic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. The handling of these devices should follow the requirements of electrostatic sensitive components. Do not attempt to disassemble this camera. Do not expose this camera to rain or moisture. Do not face this camera towards the sun, extreme bright light or light reflecting obje
