ページ1に含まれる内容の要旨
Development of the PV1
ページ2に含まれる内容の要旨
The Problem The holy grail of subwoofer design is deep and clean bass from a near-invisible box. The immediate problem that arises is that reduced box size both curtails bass extension and increases pressure on the enclosure wall and driver diaphragm. Many small subwoofers are unable to reproduce sufficiently extended bass and suffer from considerable cabinet coloration, often resulting in bass that is uneven and dissociated from the midrange and treble. Some existing designs have tried to addre
ページ3に含まれる内容の要旨
To illustrate this, there are two analogies that we can apply. The first is the soap bubble. An undisturbed bubble assumes a spherical shape because the pressure difference inside and out is perfectly balanced by the only force the bubble can sustain - surface tension that is entirely in the curved plane of the skin. The second important analogy is found in the architecture of Antonio Gaudi. For our subwoofer, not only do we have to consider pressure changes in the enclosed volume of air, we mus
ページ4に含まれる内容の要旨
These effects are related to the ratio of the sound The problems inherent to small subwoofers are often compounded further by the industrial designer’s desire to wavelength to the dimensions of the enclosure. The shave off centimetres here and there. The beauty of the resulting pressure and force gradients allowed the PV1 is precisely that its non-bending cabinet design reintroduction of bending forces on the walls of the permits the use of a relatively thin aluminium shell, sphere, which raised
ページ5に含まれる内容の要旨
A secondary consequence of the use of twin opposing Naturally, the driver must be capable of handling this drivers is the inherently balanced kinetic nature of the power. The large magnet structure aids control of the device. It is well known that the reproduction of bass motion of the diaphragm and forms an effective heat with correct dynamics requires a firm, solid foundation – sink for the voice coil, which, at 30mm long, allows sometimes referred to as a mechanical ground. It is the sufficient
ページ6に含まれる内容の要旨
low-pass filter 80Hz dB EQ = i EQ = ii EQ = iii PV1 - frequency response 100 10 1 % Bandpass output level 90dB at 1m 0.1 0.01 PV1 - total harmonic distortion -20 The vibration levels of the PV1 (red) are -30 compared with those of a conventional -40 subwoofer (blue) of similar bandwidth, output capability and drive unit radiating -50 dB area, but using a single 250mm driver in a -60 heavily braced wooden cabinet. -70 Measurements were made by scanning -80 the enclosure surfaces with a laser beam
ページ7に含まれる内容の要旨
Technical features Pressure vessel enclosure 500W ICEpower® amplifier Switch mode power supply Description Active closed-box subwoofer system Drive unit 2x 200mm (8 in) dia mica / aluminium diaphragm long-throw -6dB at 18Hz and 40/140Hz adjustable (EQ at i) Frequency range Frequency response ±3dB 21Hz – 31/110Hz adjustable (EQ at i) Amplifier Power output: 500W Rated power consumption: 110W (105W - 100V version) Input impedance: 100kohms Signal / noise: >90dB Functions: Volume level Low-pass filt
ページ8に含まれる内容の要旨
B&W Group Ltd UK Sales Enquiries and Service B&W Group (Asia) Ltd B&W Group Ltd Dale Road T +44 1903 221 500 T +852 2 869 9916 reserves the right to amend Worthing West Sussex E uksales@bwgroup.com E showroom@bwgroup.hk details of the specifications BN11 2BH England without notice in line T +44 (0) 1903 221800 with technical developments. F +44 (0) 1903 221801 Copyright © B&W Group Ltd. B&W Loudspeakers of America E info@bwgroup.com T +1 978 664 2870 www.bwgroup.com ICEpower is a registered E mar
