ページ1に含まれる内容の要旨
OPERATING INSTRUCTIONS
SR-F1B
SPEAKER SYSTEM
SR-L1B
SUPER WOOFER SYSTEM
SR-L1B
SR-F1B
Note: The SR-F1B comes with two nuts on the bottom side, which
are used only for mounting the SR-F1B to an optional
speaker stand. Never use these nuts for speaker suspension.
FEATURES
SR-F1B
Electronic-controlled system (bi-amplifier driven system) with the AC-F1 Electronic Control Unit.
High power capacity of 120 watts continuous pink noise for low frequency and 80 watts for high frequency.
High-efficiency 30
ページ2に含まれる内容の要旨
INPUT CONNECTOR Each speaker employs the Neutrik NL4MPR connector for its input. Contact number SR-F1B SR-L1B The table on the right shows the NL4MPR's contact arrangement. The mated cable connector is the Neutrik NL4FC. * Woofer direction viewed from the front side. CONNECTION DIAGRAMS Single System (SR-F1B) Mixer / preamplifier SR-F1B Combination System (SR-F1B and SR-L1B) SR-F1B SR-F1B Mixer/ preamplifier SB-L1B Note: Refer to the "Electronic control unit's operating instructions" for the mod
ページ3に含まれる内容の要旨
Suspending the SR-F1B Note: The SR-L1B can not be suspended. Caution The SR-F1B weighs approximately 37 kg. Confirm that the structure of installation place, and suspending wires or belts are heavy-duty enough to support the total weight of the load before suspension. Secure to lock the fixing metals of the suspending wire or belt to the speaker. TOA takes no responsibility for any accidents or injuries resulting from the fall of the SR-F1B due to incorrect installation. • As for the general sus
ページ4に含まれる内容の要旨
SPECIFICATIONS SR-L1B SR-F1B Enclosure Bass reflex type Low frequency One 30cm(12 " ) dia. cone speaker Two 38cm (15 ") dia. cone speakers Speaker CD horn (60° horizontal by 40° Vertical) High frequency — plus compression driver Low frequency : 8 Rated impedance 8 X2 High frequency : 16 Low frequency : 98dB(1W/1m) Sensitivity 96dB(0.5Wx2/1m) High frequency : 110dB(1 W/1m) Frequency response 70 Hz~20 kHz at AC-F1 's use 35 Hz~1 kHz Crossover frequency 1 kHz at AC-F1's use 125 Hz at AC-L1's use Co
ページ5に含まれる内容の要旨
SR-F1B SPEAKER FLYING SYSTEM This speaker flying hardware system is manufactured by ATM FLY-WARE™ (ATM GROUP, Inc.) of the United States for use with TOA's SR-F1B speaker. The flying system enables various speaker array configurations to be constructed quickly and safely without special components. SYSTEM COMPOSITION AMFS-1X2-SME The flying system is comprised of five main components. AMFS-1X2-SME 2.5QRP AMFS-1x2-30 1 .[AMFS-SRF1-TH Truss Module] Allowable load 275 kg 2.5QRP The truss module att
ページ6に含まれる内容の要旨
SR-F1B SPEAKER STAND This speaker stand is manufactured by König&Meyer GmbH(K&M) of Germany for use with TOA's SR-F1B speaker. The speaker stand consists of two main sections: Stand: Model 213 Bracket: Model 19582 USAGE (Refer to Fig. 1.) Extending the Stand Legs. 1 . Loosen the tripod clamp screw and extend the tripod legs by sliding the clamp ring down the length of the stand until the leg stays are horizontal, then retighten the screw. Mounting the Speaker. 2 . Attach the stand brack
ページ7に含まれる内容の要旨
SR-F1B
ページ8に含まれる内容の要旨
SR-F1B
ページ9に含まれる内容の要旨
SR-F1B SR-L1B TOA
ページ10に含まれる内容の要旨
2
ページ11に含まれる内容の要旨
3
ページ12に含まれる内容の要旨
133-01-380-50
ページ13に含まれる内容の要旨
INSTRUCTION MANUAL SAFETY PRECAUTIONS Follow this instruction manual to obtain the optimum Symbols results before use. Symbol of Symbol of We also recommend you keep this instruction manual caution actions prohibited actions handy for future reference. Note that this manual may include safety precautions not applied to your products. Caution Prohibition Indicates a potentially hazardous situation which, if mishandled, could WARNING result in death or serious personal injury. Avoid installing or
ページ14に含まれる内容の要旨
* Please see the reverse side for English safety instructions. TOA
