ページ1に含まれる内容の要旨
XPA2100
XPA4100
XPA6100
XPA SERIES
INSTALLATION/OWNER’ S MANUAL
Mobile Power Amplifiers
ページ2に含まれる内容の要旨
XPA SERIES INSTALLATION Preparation Please read entire manual before installation. Due to the technical nature of amplifiers, it is highly recommended that your DUAL amplifier is installed by a professional installer or an authorized dealer. Before You Start • Disconnect negative battery terminal. (consult a qualified technician for instructions) • Avoid installing the amplifier where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject t
ページ3に含まれる内容の要旨
XPA SERIES INSTALLATION Connection Descriptions NOTE Be sure to follow specific instructions included with your amplifier installation kit (not included with this amplifier). The information below should be used a general guideline only. Power Wire (+12V) • Disconnect negative battery terminal before proceeding. Consult a qualified technician for instructions if you are unsure. • Plan wire routing before cutting any wires to length. Begin by routing the power +
ページ4に含まれる内容の要旨
XPA SERIES INSTALLATION Power and Speaker Connections XPA2100 4 5 1 2 3 XPA4100 1 5 4 3 2 XPA6100 1 5 4 3 2 Speaker Connection(s) +12VDC Battery Connection 1 4 Ground Connection 2 5 Fuse(s) Remote Connection 3 4
ページ5に含まれる内容の要旨
XPA SERIES INSTALLATION Audio Inputs and Controls XPA2100 1 2 3 4 5 6 7 8 XPA4100 1 7 2 3 4 5 6 7 XPA6100 1 2 4 5 6 7 LED Indicator Input Level Control 1 5 Bass Boost High Level Inputs 2 6 Crossover Mode Switch Low Level Inputs 3 7 Crossover Frequency Input Mode Switch 4 8 5
ページ6に含まれる内容の要旨
XPA SERIES INSTALLATION Typical Wire Routing Main Power Connections Connect +12V, GND and REM wires accordingly. A suitable fuse MUST be installed on the +12V lead within 18" of the battery for protection of the vehicle’s electrical system. Fuse Rating Power/Ground Wire Size When replacing fuses, make sure new fuse For optimum performance, use only the wire is the correct type and amperage. Using an size listed below or larger. Make sure to use incorrect fuse could damage the amplif
ページ7に含まれる内容の要旨
XPA SERIES INSTALLATION Amplifier Connections Subwoofer (mono) Speaker Connections 2 Speakers (stereo) Connect speaker wires observing polarity. The minimum impedance load for the XPA2100 and XPA4100 is 2 ohms stereo and 4 ohms bridged. The minimum impedance load for the XPA6100 is 2 ohms. Use of loads lower than these is not recommended and may cause amplifier damage.The XPA2100 and XPA4100 can be wired for stereo, bridged or stereo/bridged Typical Stereo Wiring Typical Brid
ページ8に含まれる内容の要旨
XPA SERIES OPERATION Configuration/Setup Input level Control The input level control (gain) is used to obtain the best possible match between the head unit audio output and the amplifier input. Begin by turning the input level control fully counterclockwise. Next, turn up the head unit volume control around 3/4 of the way up. Adjust the input level control clockwise until audible distortion is heard, then slightly counterclockwise to provide the best match. Repeat for all input level
ページ9に含まれる内容の要旨
XPA SERIES WARRANTY Limited One-Year Warranty This warranty gives you specific legal rights. What to do? You may also have other rights which vary from 1. Before you call for service, check the state to state. troubleshooting guide in your owner’s manual. A slight adjustment of any custom Dual Electronics Corp. warrants this product to controls may save you a service call. the original purchaser to be free from defects in material and workmanship for a period of one 2. If you require
ページ10に含まれる内容の要旨
XPA SERIES OPERATION Specifications CEA-2006 Power Standard Specifications (reference: 14.4VDC, 20Hz~20kHz) XPA2100 Power Output: 50 Watts RMS x 2 channels at 4 ohms and < 1% THD+N Signal to noise ratio: 75dBA (reference: 1 watt into 4 ohms) Additional power output: 75 Watts RMS x 2 channels at 2 ohms and < 1% THD+N 150 Watts RMS x 1 channel at 4 ohms (bridged) and < 1% THD+N Dynamic power: 300 Watts at 4 ohms Frequency response: 20Hz~
ページ11に含まれる内容の要旨
XPA SERIES OPERATION Specifications CEA-2006 Power Standard Specifications (reference: 14.4VDC, 20Hz~200Hz) XPA6100 Power Output: 200 Watts RMS x 1 channel at 4 ohms and < 1% THD+N Signal to noise ratio: 72dBA (reference: 1 watt into 4 ohms) Additional power output: 300 Watts RMS x 1 channel at 2 ohms and < 1% THD+N Dynamic power: 600 Watts at 2 ohms Frequency response: 20Hz~200Hz (-3dB) Maximum input signal: 6V Minimum input signal: 200mV Speaker
ページ12に含まれる内容の要旨
XPA SERIES OPERATION Troubleshooting Problem Cause Action Unit will not turn on +12V wire not connected or incorrect voltage Check connections for proper voltage (no power LED indicator) REM wire not connected or incorrect voltage (11~16VDC) GND wire not connected Check connection to ground Fuse(s) blown Replace fuse(s) Unit has power - LED is Speaker wires not connected Check connections at speakers green (but no sound) Volume turned all the way down Increase volume level
