ページ1に含まれる内容の要旨
O W N E R ' S M A N U A L
HCA-806A Six Channel High Current Power Amplifier
-1-
HCA-806A High Current Multi Amplifier HCA-806A High Current Multi Amplifier
Current Overload
5 6
1 2 3 4
AC Line Standby Normal
Power Power
ページ2に含まれる内容の要旨
Table of Contents Important Safety Instructions ........................................................................................ 3 Figure #1 and #2 HCA-806A Front and Rear Panel Drawings ..................................... 4 Introduction ..................................................................................................................... 5 Installing and Rack Mounting Your Amplifier................................................................ 5 Ventilation Requiremen
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of “dangerous voltage” inside the product that may constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the product. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO US
ページ4に含まれる内容の要旨
HCA-806A Front and Rear Panel Controls EIA Rack Mount Holes Power Switch Status Indicators Figure #1 HCA-806A Front Panel Controls + 12 Vdc Trigger Connector Bridge Switches DC Trigger CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 Fuse 10 A +12 V GND Main Fuse Level Controls Levels Off Off Loop 1/2-3/4 CH 3+ Ch 4 Loop 1/2-3/4 CH 3+ Ch 4 Input Connectors Inputs On Mono Bridging On Mono Bridging HCA - 806A High Current Multi-Amplifier Parasound Products, Inc Independant Independant San Francisco, C
ページ5に含まれる内容の要旨
Introduction Congratulations on your purchase of this precision audio component and thank you for your selection of Parasound. Please take a few moments to read these instructions so that you may fully understand the capabilities of your new Parasound power amplifier. Unpacking Your Amplifier Carefully unpack your amplifier and remove all the enclosed accessories. Be sure to inspect the unit for any possible shipping damage. If you see any, contact your Parasound Dealer immediately. Save all the
ページ6に含まれる内容の要旨
Input Connections and Switch Settings for the HCA-806A Refer to Figure #2 Six Channel Operation The six channel mode of your HCA-806A can power the six speakers required for a complete home theater: Front left and right, surround left and right, center channel, and subwoofer. Connect each output from your surround processor to the corresponding input connector of your HCA-806A. If you are using your HCA-806A in the six channel mode, we suggest the following progression of channel priorities. Th
ページ7に含まれる内容の要旨
Multi-Zone Stereo Operation Refer to Figure #2 You can switch your HCA-806A to reproduce a single stereo source through up to three pairs of stereo channels via input cables connected to channels 1 and 2 input jacks only. This permits a neater and less confusing hookup. It eliminates the requirement for two or four “Y” adapters in order to split your preamplifier’s single pair of stereo outputs to feed the 3 pairs of HCA-806A power amplifier input jacks. When you switch the LOOP 1/2 > 3/4 Swi
ページ8に含まれる内容の要旨
Mono Bridging — Channels 3+4 and 5+6 When you bridge channels 3+4 and/or 5+6, your speakers are connected to the bridged channels differently. You bridge by using the red + terminals of the adjacent channel pairs only. Note that bridged connections are made horizontally rather than vertically and that the upper red + terminals have separate markings for bridging. In the bridged mode, channel 4 (and/or 6) output is positive and channel 3 (and/or 5) output is negative. Unbridged speaker connect
ページ9に含まれる内容の要旨
Operating Your HCA-806A Power Switch Manual Turn On Press the upper side to turn the unit on manually; press the lower side to turn the unit off. Automatic Turn On When the power switch is in the off position, the power amplifier can be turned on with an external DC voltage applied at the DC trigger connector on the rear panel. (See above) AC Line LED The AC line LED on the front panel of your amplifier will illuminate whenever AC is present at the AC connector. This LED indicates that the AC c
ページ10に含まれる内容の要旨
In Case of Trouble If you suspect a problem with this unit, first recheck all your connections. If only one channel is inoperative, the trouble may be caused by another component or even a defective hookup cable. However, if the same channel is at fault when you reverse the Left and Right channel pair cables to your HCA-806A (turn it off before moving wires), it may indicate trouble within the power amplifier itself. We suggest you contact your authorized Parasound Dealer or Installer, or call
ページ11に含まれる内容の要旨
Parasound HCA-806A Specifications Continuous Power Output > 80 watts RMS x 6, 20 Hz - 20 kHz, 8 W , all channels driven > 120 watts RMS x 6, 20 Hz - 20 kHz, 4 W , all channels driven Continuous Power Output - Bridged > 180 watts RMS, 20 Hz - 20 kHz, 8 , each bridged channel, 3+4, 5+6 Current Capacity 30 amperes peak, per channel Slew Rate > 130 V/μsecond Frequency Response 20 Hz - 120 kHz, +0/-3 dB Total Harmonic Distortion < 0.05% at full power < 0.02% typical levels IM Distortion < 0
ページ12に含まれる内容の要旨
Parasound Limited Warranty (USA only) Your Parasound HCA-806 amplifier is covered by a limited warranty against defects in materials and workmanship for a period of two years from date of purchase. This warranty is provided by the Parasound dealer where the unit was purchased. Warranty repair will be performed only when your purchase receipt is presented to validate your ownership, date of purchase. and authorized status of the selling dealer. Defective parts will be repaired or replaced wit
