ページ1に含まれる内容の要旨
User / Installation Manual
D-Class Marine Amplifier
MS-DA51600
Specifications and design are subject to change without notice
ページ2に含まれる内容の要旨
AMPLIFIER SPECIFICATIONS Peak Power (Watts) 1600 Frequency Response 10Hz -50kHz 300(l) x 210(w) x 50(h) Dimensions (mm) 11-13/16 x 8-1/4 x 2” 80W RMS x 4 + 250W RMS x 1 @ 4Ω 1% THD+N 130W RMS x 4 + Power Ratings 330W RMS x 1 @ 2Ω 1% THD+N 250W RMS x 2 @ 4Ω Bridged 1% THD+N + 250W RMS x 1 @ 4Ω 1% THD+N INSTALLATION GUIDELINES 1. Ensure the +12V lead is disconnected from the 5. Ensure the mounting location has sufficient battery before you connect any new equipment. air flow around the amplifie
ページ3に含まれる内容の要旨
LEVEL CONTROL This control is used to match the input level of the amplifier to the output level of you head unit. We recommend the following method. NOTE: Remove screws and the top cover of amplifier to access controls. 1. Turn the amplifier level to zero 3. Adjust the level control until the desired maximum volume is achieved without distortion. 2. Turn the volume of the head unit to and the bass and treble to zero 4. Failure to follow these steps may cause permanent damage to the audio sy
ページ4に含まれる内容の要旨
AMPLIFIER DIMENSIONS 300 11-13/16" 268 10-9/16" All dimensions provided are in millimeters (mm) unless indicated 4 6.5 1/4" 12 15/32" 160 6-5/16" 50 1-31/32" 210 8-9/32"
ページ5に含まれる内容の要旨
CONTROL DESCRIPTIONS 1 2 3 4 5 6 7 8 9 10 1. SPEAKER OUTPUT: Connect your speakers to these terminals. 14 2. FRONT RCA INPUT: Connect these RCA connectors to a head unit with a front low level output connection. 3. REAR RCA INPUT: 11 15 Connect these RCA connectors to a head unit with a rear low level output connection. 16 16 17 4. SUBWOOFER RCA INPUT: 12 Connect these RCA connectors to a head unit with a subwoofer low level output connection. 18 5. REMOTE LEVEL CONTROL CONNECTION: 19 13 Conn
ページ6に含まれる内容の要旨
INSTALLATION INSTRUCTIONS 3 CHANNEL INSTALLATION (2-8 Ohm) (2-8 Ohm) RL RR (2-8 Ohm) 6
ページ7に含まれる内容の要旨
5 CHANNEL INSTALLATION (2-8 Ohm) (2-8 Ohm) RL RR FL FR (2-8 Ohm) (2-8 Ohm) (2-8 Ohm) 7
ページ8に含まれる内容の要旨
resistance amperage current TECH TIPS BASIC TOOLS In any installation these basic tools may be required. For custom type installations, additional tools may be neccesary. • Elec tric drill • Fla t blade scr e w driv er • Crimping t ool • Elec trical tape • Allen k ey se t • Phillips scr e w driv er • Wir e strippers • Silic on sealant • Utility knif e, sabr e saw , jigsaw , nibbler OHMS LAW SIMPLIFIED E IR I 2 W E I W W WR 2 I E R 2 IW E E R R W 2 I R E W/REI 8 voltage watts
ページ9に含まれる内容の要旨
SERIES AND PARALLEL SUBWOOFER WIRING FOR DUAL VOICE COIL SUBWOOFERS PARALLEL VOICE COIL WIRING (2 OHM OPERATION) To wire a 4 Ohm DVC subwoofer in parallel to get 2 Ohm, use two short pieces of speaker wire and link the positive from one coil to the positive of the second coil, and do the same for the negative as shown below. Then wire the amplifier to opposite sides of the subwoofer in order to equalise any connection resistance. + - 2 Ohm operation SERIES VOICE COIL WIRING (4 OHM OPERATIO
ページ10に含まれる内容の要旨
PARALLEL WIRING FORMULA FOR 2 SPEAKERS 4 Ohm 8 Ohm 2.67 Ohms R1 x R2 4 Ohms x 8 Ohms 32 = LOAD IMPEDANCE = = 2.67 Ohms R1 + R2 4 Ohms + 8 Ohms 12 SERIES WIRING FORMULA FOR 2 SPEAKERS 4 Ohm 4 Ohm 8 Ohms R1 + R2 = LOAD IMPEDANCE 10
ページ11に含まれる内容の要旨
RECORD YOUR PURCHASE DETAILS HERE: SERIAL NUMBER DATE OF PURCHASE AFFIX RECEIPT HERE www.fusionelectronics.com FUSION Electronics New Zealand Ph: +64 9 369 2900 FUSION Electronics Australia Ph: +61 1300 736 012 FUSION Electronics Europe Ph: +44 845 299 7586 FUSION Electronics USA Ph: +1 623 580 9000 For further product and installation information, please visit www.fusionelectronics.com Pour plus d’informations sur les produits et l’installation, rendez-vous sur www.fusionelectronics.com Para
ページ12に含まれる内容の要旨
