ページ1に含まれる内容の要旨
8 Port HD/SD-SDI Switch
User’s Guide
Models
SW-HDSDI-8X1
© 2008 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations
or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to
specifications and product descriptions at any time without notice. No license, whether exp
ページ2に含まれる内容の要旨
Table of Contents Section 1: Getting Started ...................................................................................................................... 3 1.1 Important Safeguards ............................................................................................................ 3 1.2 Safety Instructions ................................................................................................................. 3 1.3 Regulatory Notices Federal Communications Commi
ページ3に含まれる内容の要旨
Section 1: Getting Started 1.1 Important Safeguards Please read all of these instructions carefully before you use the device. Save this manual for future reference. What the warranty does not cover Any product, on which the serial number has been defaced, modified or removed. Damage, deterioration or malfunction resulting from: Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions suppl
ページ4に含まれる内容の要旨
1.3 Regulatory Notices Federal Communications Commission (FCC) This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. 1.4 Introduction Avenview SW-HDSDI-8X1, 8 Port HD/SD-SDI Switch receives, equalizes 8 SDI inputs, perfectly switch
ページ5に含まれる内容の要旨
1.6 Before Installation Put the product in an even and stable location. If the product falls down or drops, it may cause an injury or malfunction. Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high humidity. Use the DC power adapter with correct specifications. If inappropriate power supply is used then it may cause a fire. Do not twist or pull by force ends of the optical cable. It can cause malfunction. 1.7 Panel Description
ページ6に含まれる内容の要旨
7. Power Switch 8. 5V DC Power Jack 9. SYNC Signal Input 10. SDI Output 11. SYNC Signal Loop Out 12. SDI Input 1.8 Installation To setup Avenview SW-HDSDI-8X1 follow these steps for connecting to a device: 1. Connect SDI enable equipments to the output of SW-HDSDI-8X1 2. Connect the SDI input sources to the inputs of SW-HDSDI-8X1 3. Plug power adapter cable into 5V DC power jack of SW-HDSDI-8X1 4. Use IR Remote, RS232 or front panel push button to switch between inputs.
ページ7に含まれる内容の要旨
Section 2: Specifications Item Description SD-SDI SDI Standards HD-SDI Auto HD/SD-SDI Detection Yes Supported Protocols SMPTE 259M / SMPTE 292M Video Bandwidth Single Link: 1.485Gbps & 1.485 / 1.002 Gbps Data Rates 143 / 270 / 1483 / 1485 Mbps HD: 720p50/59.94/60, 1035i50/59.94/60, 1080i50/59.94/60, 1080p24/30 Video Support SD: NTSC@59.94Hz, PAL@50Hz Output Impedance 75Ω HD-SDI: up to 150m Cable Equalization SD-SDI: up to 300m Synchronized BNC loop-out at input and output Loop O
ページ8に含まれる内容の要旨
Disclaimer While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequentia
