ページ1に含まれる内容の要旨
KAV–300iL
Remote Control
THE LEADER IN AUDIO ENGINEERING
Integrated Amplifier
Instructions for Use
Owner’s Reference
ページ2に含まれる内容の要旨
KAV–300iL Remote Control Integrated Amplifier Instructions for Use v 01.2 CONTACT Krell Industries, Inc. INFORMATION 45 Connair Road Orange, CT 06477-3650 USA TEL 203-799-9954 FAX 203-891-2028 E-MAIL krell@krellonline.com WEBSITE http://www.krellonline.com This product complies with the EMC directive (89/336/EEC) and the low-voltage directive (73/23/EEC). Do not place the integrated amplifier where it could be exposed to dripping or WARNINGS splashing. The ventilation grids on the top and bo
ページ3に含まれる内容の要旨
Contents Page INTRODUCTION 1 DEFINITION OF TERMS 2 UNPACKING 4 PLACEMENT 5 AC Power Guidelines 5 Power Cord 5 FRONT PANEL DESCRIPTION 7 BACK PANEL DESCRIPTION 10 REMOTE CONTROL DESCRIPTION 13 Battery Installation and Removal 13 Remote Control Functions 13 CONNECTING THE KAV–300iL TO YOUR SYSTEM 15 Connection Steps 15 OPERATING YOUR KAV–300iL 16 Amplifier Operation 16 Tape Input and Output 17 OPTIONAL CONFIGURATIONS 18 Configuring the KAV–300iL for Theater Throughput 18 HOW TO TROUBLESHOOT SYSTEM
ページ4に含まれる内容の要旨
Illustrations Page FIGURE 1 The KAV–300iL Front Panel 6 FIGURE 2 The KAV–300iL Back Panel 9 FIGURE 3 The KAV–300iL Remote Control 12 iv Krell KAV–300iL
ページ5に含まれる内容の要旨
Introduction Thank you for your purchase of the Krell KAV–300iL Remote Control Integrated Amplifier. This fully integrated amplifier and pre- amplifier has a fully balanced signal path from input to output and employs a wide bandwidth design with low negative feedback for sonic accuracy throughout the frequency spectrum. All circuits up to the driver stage are pure Class A. Krell’s new surface mount technology (SMT) means that the KAV–300iL is an integrated amplifier with big power—200 Watts pe
ページ6に含まれる内容の要旨
Definition of Terms Following are the definitions of key terms used in your owner’s ref- erence manual. CONFIGURATIONS Theater Throughput Theater Throughput is a Krell configuration option that allows the signal from a surround preamp/processor to pass through a Krell preamplifier or integrated amplifier with no gain, for integrated vol- ume and balance management of Krell home theater systems. INPUT AND OUTPUT Balanced CONNECTIONS A symmetrical input or output circuit that has equal impedance
ページ7に含まれる内容の要旨
Definition of Terms, continued TECHNOLOGY Krell Current Mode A proprietary Krell circuit topology in which the audio gain stages of a component operate in the current rather than voltage domain. This unique technology provides the component with exceptional speed and a wide bandwidth. Krell KAV–300iL 3
ページ8に含まれる内容の要旨
Unpacking After opening the box and removing the top layer of foam, the KAV–300iL and the KAV–300iL accessory kit containing the follow- ing items will be visible: 1 AC power cord 1 12 VDC (12 V trigger) cable 2 spare loudspeaker fuses (AGC 8) 1 KAV–300iLremote control 1 CR2025 lithium battery Grasp the underside of the amplifier and lift it straight out of the packing box. Place the amplifier in a safe location and remove the protective plastic wrapping. Notes If any of these items are not inc
ページ9に含まれる内容の要旨
Placement Before you install the KAV–300iL into your system, review the fol- lowing guidelines to choose the location for the KAV–300iL. This will facilitate a clean, trouble-free installation. The KAV–300iL does not require any type of special rack or cabinet for installation. For the dimensions of the KAV–300iL, see Specifications, on the back cover. Place the KAV–300iL on a firm, level surface, away from excessive heat, humidity, or moisture. The KAV–300iL requires at least two inches (5 cm)
ページ10に含まれる内容の要旨
Figure 1 The KAV-300iL Front Panel 3 1 2 4 6 7 8 9 11 10 5 Power Mode Indicators 1 Power Button 8 Mute Button 2 Power LED 9 Mute LED 3 Stand-by LED 4 Infrared Sensor Volume Adjustment Functions Analog Devices 10 Level Up 5 S-1, S-2, S-3, and and Down Buttons B-1 Buttons and LED 11 Front Panel Display 6 Tape Button 7 Tape LED
ページ11に含まれる内容の要旨
Front Panel Description See Figure 1 on page 6 The front panel of the KAV–300iL accesses power on and off, analog input selections, volume control, and mute. The front panel display shows the volume and balance levels, and Theater Throughput status. POWER 1 Power Button Use this button to switch the KAV–300iL between the stand-by and the operational modes. 2 Power LED The blue power LED illuminates when the KAV–300iL is in the operational mode. The power LED also flashes when any remote contro
ページ12に含まれる内容の要旨
Front Panel Description continued MODE INDICATORS 8 Mute Button Use this button to interrupt the signal of the input you have select- ed. To unmute, press the mute button again. 9 Mute LED The red mute LED illuminates when you press the mute button or mute key (28) on the remote control. VOLUME ADJUSTMENT 10 Level Up and Down Buttons FUNCTIONS The volume level buttons adjust the amplifier output level, which is indicated numerically on the front panel display; range is 0-151. 11 Front Panel Di
ページ13に含まれる内容の要旨
Figure 2 The KAV-300iL Back Panel 19 30 18 INPUTS OUTPUTS 12VDC RC–5 50/60 Hz RIGHT OUTPUT B–1 RIGHT B–1 LEFT S – 1 S – 2 S – 3 TAPE TAPE PREAMP OUT IN IN LEFT OUTPUT LEFT RIGHT FUSE FUSE AGC 8 AGC 8 NO USER SERVICEABLE PARTS INSIDE KAV–300iL MADE IN USA 23 12 13 14 15 16 17 12 23 22 21 Amplifier Channel Analog Outputs Outputs 16 Left and Right Tape Outputs 12 Left and Right Loudspeaker 17 Left and Right Preamp Outputs Outputs Remote Connections Analog Inputs 18 RC-5 In 13 Left and Right Balanc
ページ14に含まれる内容の要旨
Back Panel Description See Figure 2 on page 9 The KAV–300iL back panel provides connections for all inputs and outputs, power on/off, and additional remote connections. AMPLIFIER CHANNEL 12 Left and Right Loudspeaker Outputs OUTPUTS The KAV–300iL is equipped with standard binding posts for each amplifier channel. These connectors accept bare wire, pins, or spade lugs. Use the red terminal for the positive connection and the black terminal for the negative connection. 13 Left and Right Balanced A
ページ15に含まれる内容の要旨
Back Panel Description, continued REMOTE 20 12 VDC In CONNECTIONS, The KAV–300iL is equipped with an input that receives 12 VDC continued (12 V trigger) power on/off signals from other Krell components and other devices that incorporate a 12 V trigger. This allows you to turn the KAV–300iL on or off, or to and from stand-by, from other components. Notes The 12 VDC output current is limited to 30 ma. Consult the owner’s reference of the components used in a custom installation to take full advan
ページ16に含まれる内容の要旨
Figure 3 The KAV-300iL Remote Control Power 24 Power Key 25 Pre Key 24 25 Analog Functions 27 26 Analog Input Keys 28 27 Tape Key Output Control Functions 29 26 29 Mute Key 29 Vol (Volume) Keys 30 Bal (Balance) Keys 30 Note Remote control keys listed above function with the KAV-300iL. Other keys on this remote control may activate other Krell components. Consult the Krell reference manual for each model to review your component’s full remote control capabilities. 12 Krell KAV–300iL
ページ17に含まれる内容の要旨
Remote Control Description See Figure 3 on page 12 The KAV-300iL remote control uses one CR2025 lithium battery, Battery which is included with the shipment. Installation and To open the battery compartment on the back of the remote control: Removal 1. Place the remote face down on the table. 2. Use your thumbnail or a small jeweler’s or eyeglass screw- driver to move the small switch toward the center of the remote, while using your index fingernail or screwdriver to pull down gently on the
ページ18に含まれる内容の要旨
Remote Control Functions continued ANALOG FUNCTIONS 26 Analog Input Keys Use these keys to select a balanced source (B-1) or single-ended sources (S-1, S-2, or S-3). The selected input LED on the front panel illuminates. 27 Tape Key Use this key to monitor the output signal of a three-head analog tape recorder, compared to the output signal from an audio source, when making a recording. See Tape Input and Output, on page 17. The red tape monitor LED on the front panel illumi- nates when the
ページ19に含まれる内容の要旨
Connecting the KAV–300iL to Your System USING BALANCED Krell recommends using balanced interconnect cables. Balanced CONNECTIONS interconnect cables not only can minimize sonic loss but are also immune to induced noise, especially with installations using long cables. Balanced connections have 6 dB more gain than single- ended connections. When level matching is critical, keep this gain value in mind. Follow these steps to connect the KAV–300iL to your system. Connection Steps 1. Make sure all
ページ20に含まれる内容の要旨
Operating Your KAV–300iL This section provides information about operating the KAV–300iL. The KAV–300iL provides basic input selection and volume control operation from the front panel. The remote control includes addi- tional preamplifier functions as well as CD transport and amplifier controls. See Remote Control, on page 13, for more information. After the KAV–300iL is connected to AC power and is in the stand-by mode, use the power button (1) or key (24) to switch the component to the oper
