ページ1に含まれる内容の要旨
10/100/1000 Gigabit
Switches
Use this guide to install the following products:
SD2005 5-Port 10/100/1000 Gigabit Switch
SD2008 8-Port 10/100/1000 Gigabit Switch
User Guide
ページ2に含まれる内容の要旨
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2003 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders. LIMITED WARRANTY Linksys warrants to the original end user purchaser (“You”) that, for a period of the product’s lifetime, (the “Wa
ページ3に含まれる内容の要旨
Table of Contents Chapter 1: Introduction The 10/100/1000 Gigabit Switch Chapter 1: Introduction 1 The 10/100/1000 Gigabit Switch 1 The 5- or 8-Port 10/100/1000 Gigabit Switch provides non-blocking, wire Features 1 speed switching for your 10, 100, and 1000 megabit network clients. Drop this Switch in place of your current workgroup hub or switch, and you can Chapter 2: Getting to Know the 10/100/1000 upgrade your high-requirement workstations to full Gigabit speeds as neces- Gigabit Switch 2 sa
ページ4に含まれる内容の要旨
Chapter 2: Getting to Know the 10/100/1000 Gigabit Switch Overview The 5- and 8-Port 10/100/1000 Gigabit Switches differ in number of LEDs and Figure 2-3 ports. Pictured here is the 5-Port Switch; however, the other Switch is similar in form. The power port is located on the side panel of the Switch (see Figure 2-3). Front Panel LEDs (power) The power port is where you will connect the included power adapter. Figure 2-1 System Green. The System LED will light up when the Switch is powered on. F
ページ5に含まれる内容の要旨
Connecting Network Devices Chapter 3: Connecting the To connect network devices to the Switch, follow these instructions. 10/100/1000 Gigabit Switch 1. Make sure all the devices you will connect to the Switch are powered off. Overview 2. Connect a Category 5 Ethernet This chapter will explain how to connect network devices to the Switch. For an network cable to one of the example of a typical network configuration, see the application diagram shown numbered ports on the Switch. in Figure 3-1.
ページ6に含まれる内容の要旨
Placement Options Appendix A: Glossary Set the Switch on its four rubber feet, or hang the Switch on a wall using its wall-mount slots. 10BaseT - An Ethernet standard that uses twisted wire pairs. To use the wall-mount option, follow these instructions: 100BaseTX - IEEE physical layer specification for 100 Mbps over two pairs of Category 5 UTP or STP wire. 1. The wall-mount slots are two crisscross slots on the Switch’s 1000Base-T - Provides half-duplex and full-duplex 1000Mbps Ethernet service
ページ7に含まれる内容の要旨
Fast Ethernet - A 100 Mbps technology based on the 10Base-T Ethernet Appendix B: Specifications CSMA/CD network access method. Hub - The device that serves as the central location for attaching wires from Model Number SD2005 5-Port 10/100/1000 Gigabit Switch workstations. Can be passive, where there is no amplification of the signals; or SD2008 8-Port 10/100/1000 Gigabit Switch active, where the hubs are used like repeaters to provide an extension of the cable that connects to a workstation. Sta
ページ8に含まれる内容の要旨
Appendix C: Warranty Information Appendix D: Contact Information BE SURE TO HAVE YOUR PROOF OF PURCHASE AND A BARCODE For help with the installation or operation of this 10/100/1000 Gigabit Switch, FROM THE PRODUCT’S PACKAGING ON HAND WHEN CALLING. contact Linksys Technical Support at one of the phone numbers or Internet RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF addresses below. PURCHASE. Sales Information 800-546-5797 (LINKSYS) IN NO EVENT SHALL LINKSYS’S LIABILITY EXCEED THE PRICE
ページ9に含まれる内容の要旨
http://www.linksys.com © Copyright 2003 Cisco Systems, Inc. All Rights Reserved.
