ページ1に含まれる内容の要旨
Amplifier Manual
Manuel de l’amplificateur
Models: Ti1500.1, Ti2500.1
Ti600.4, Ti800.4
Features
• 24dB V ariable Low Pass and Subsonic Cr ossovers (T i2500.1, T i1500.1)
• 18dB V ariable High and Low Pass Cr ossovers (T i800.4, T i600.4)
• Cr ossovers featur e 41 Detents for Exact Fr equency Selection
• Audiophile Bi-Polar Output T ransistors (T i800.4, T i600.4)
• High Efficiency Class D T opology (T i2500.1, T i1500.1)
• Massive Unr egulated Power Supplies featuring Hand W ound T ransfor
ページ2に含まれる内容の要旨
Amplifier Owner’s Manual Specifications MONOBLOCK SPECIFICATIONS Frequency Response: ± 1dB from 20Hz to 300Hz Signal to Noise Ratio: >90dB Subsonic and Low Pass Crossovers: 24dB per octave Low Pass Crossover Range: 30Hz to 300Hz Subsonic Crossover Range: 10Hz to 55Hz Bass Boost @ 45Hz: 0 to +18dB Low Level Input Range: 200 millivolts to 8 volts Lowest Recommend Load: 1 ohm Typical Efficiency: 80% Damping Factor: Greater than 200 Ti1500.1 Ti2500.1 Dynamic Power 14.4Vdc >1% THD 1100 x 1 @ 2 ohm D
ページ3に含まれる内容の要旨
Amplifier Owner’s Manual ti2500.1 - ti1500.1 Monoblock Power Amplifier REMOTE MONITORING DISPLAY (RMD) INPUT Connect optional RMD V oltage Display to this port Connect pr eamp signal cables fr om the head unit to these terminals. LEVEL OUTPUT Used to r each maximum amplifier power with a wide variety of headunits. Pr ovides a full range signal for an additional amplifier . Ther e is no signal loss if using this output. SUBSONIC CROSSOVER FREQUENCY Contr ols the highpass cr ossover point for th
ページ4に含まれる内容の要旨
Amplifier Owner’s Manual ti800.4 - ti600.4 4 Channel Power Amplifier INPUT LOW PASS LEVEL CONTROL (LPL) Connect pr eamp signal cables fr om the head unit to these terminals. This port is for connecting the optional r emote level contr ol (LPL44). This allows up to 20dB of volume adjustment. This is not a bass boost, it contr ols the level of the entir e low pass signal of the r ear channels. CROSSOVER FREQUENCY Contr ols the cr ossover point for the speaker outputs. REMOTE MONITORING DISPLAY
ページ5に含まれる内容の要旨
Amplifier Owner’s Manual Crossover Settings All cr ossover fr equency potentiometers have 41 detents or “clicks” so the end user can set the exact cr oss over fr equency desir ed. No mor e tur ning the potentiometer and guessing wher e your cr ossover points ar e. Y ou get exact contr ol of your amplifier’ s output. Ti2500.1 - Ti1500.1 Ti800.4 - Ti600.4 Subsonic LP Bass Boost HP LP Bass Boost clicks clicks (20~400hz) (40~400Hz) (10~55hz) (30~300Hz) 1 434 434 0.1 1 55 313 0.0 2 433 432 0.1 2 5
ページ6に含まれる内容の要旨
Amplifier Owner’s Manual How to strap two monoblocks Strapping or linking two Ti amplifiers allows you to deliver a ton of power into a single voice coil commonly used in SPL competitions. The example below shows two Ti1500.1s delivering a total of 3000 watts into a single 2 ohm voice coil. DO NOT STRAP AMPLIFIERS INTO A 1 OHM LOAD. NOTES: The “Master” amplifier’s preamp section controls both amplifiers. “Slave” amplifier’s pre-amp control are disabled. Min Load is 2 ohm when strapped. HEADUNIT
ページ7に含まれる内容の要旨
Manuel de l’amplificateur Spécifications CARACTÉRISTIQUES TECHNIQUES MONOBLOC Réponse en fréquence : ± 1 dB de 20 Hz à 300Hz Rapport signal/bruit : >90dB Filtres passifs subsoniques et passe-bas: 24dB par octave Plage du filtre passif passe-bas: 30Hz à 300Hz Plage du filtre passif subsonique: 10Hz à 55Hz Amplification des basses à 45 Hz : 0 à +18dB Gamme d’entrée de niveau faible: 200 millivolts à 8 volts Charge minimale recommandée: 1 ohm Efficacité type: 80% Taux d’amortissement: Supérieur à
ページ8に含まれる内容の要旨
Manuel de l’amplificateur ti2500.1 - ti1500.1 Monoblock Power Amplifier ENTRÉE ENTRÉE DE L’AFFICHAGE DE TENSION A DISTANCE (RMD) Connectez le RMD d’affichage de tension facultatif à cette prise jack. Reliez les câbles de signal préampli de l’unité principale sur ces bor nes. SORTIE GAIN NIVEAU Sert à atteindr e une puissance d’amplificateur maximale avec une grande variété Four nit un signal pleine gamme pour un amplificateur supplémentair e. Il n’y a pas de perte de signal en cas d’utilisati
ページ9に含まれる内容の要旨
Manuel de l’amplificateur ti800.4 - ti600.4 4 Channel Power Amplifier ENTRÉE COMMANDE À DISTANCE DU NIVEAU DES BASSES (LPL) Reliez les câbles de signal préampli de l’unité principale sur ces bor nes. Ce port sert à connecter la télécommande de niveau optionnelle (LPL44). Cela permet un ajustement du volume allant jusqu’à 20 dB. Ce n’est pas une amplification des basses mais permet de contrôler le niveau du signal du filtr e passe-bas. FRÉQUENCE DE FILTRE PASSIF PASSE-BAS et PASS
ページ10に含まれる内容の要旨
Manuel de l’amplificateur Réglages du filtre passif Ti2500.1 - Ti1500.1 Ti800.4 - Ti600.4 HP LP Bass Boost Subsonic LP Bass Boost clicks clicks (10~55hz) (30~300Hz) (20~400hz) (40~400Hz) 1 55 313 0.0 1 434 434 0.1 2 52 313 0.0 2 433 432 0.1 3 52 313 0.0 3 427 415 0.3 4 416 385 0.6 4 52 313 0.0 5 404 361 0.9 5 52 289 0.2 6 48 289 0.4 6 392 343 1.3 7 48 268 0.6 7 382 325 1.7 8 371 309 2.0 8 48 268 0.7 9 362 295 2.4 9 48 247 0.9 10 48 247 1.0 10 353 283 2.7 11 44 229 1.1 11 336 275 3.1 12 301 229
ページ11に含まれる内容の要旨
Manuel de l’amplificateur Comment sangle deux monoblocs AUTORADIO MASTER + CABLE RCA PRINCIPAL Relier ensemble les bornes haut-parleur négatives (-) des - amplificateurs. PAS UTILIZE SLAVE © 2010 Phoenix Gold • www.phoenixgold.com phoenix gold ti amp manual.indd 11 3/2/10 11:20:46 AM
ページ12に含まれる内容の要旨
Phoenix Gold A Division of AAMP of America™ 13190 56th Court Clearwater, Florida 33760 P: 888-228-5560 info@phoenixgold.com www.phoenixgold.com © 2010 AAMP of Florida, Inc Designed and Engineered in the USA Phoenix Gold Pr oduct W arranty LIMITED W ARRANTY ON AMPLIFIERS Phoenix Gold warrants this pr oduct to be fr ee of defects in materials and workmanship for a period of one (1) years fr om the original date of pur chase. This warranty is not transferable and applies only to the original pu
