ページ1に含まれる内容の要旨
10/100/1000Mbps
Intelligent Ethernet Switch
MGSW-2402
User’s Manaul
ページ2に含まれる内容の要旨
Trademarks Copyright PLANET Technology Corp. 2002. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in
ページ3に含まれる内容の要旨
TABLE OF CONTENTS 1. INTROUCTION........................................................................................................................................4 1.1 CHECKLIST ...............................................................................................................................4 1.2 ABOUT THE SWITCH ..................................................................................................................4 1.3 FEATURES ...............................
ページ4に含まれる内容の要旨
1. INTROUCTION 1.1 Checklist Check the contents of your package for following parts: MGSW-2402. User's manual CD. Power cord. 19” rack mount kit. RS-232 cable. Quick Installation Guide. If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair. 1.2 About the Switch The MGS
ページ5に含まれる内容の要旨
Internal power supply Auto MDI/ MDI-X on each port Network management configuration: − Web-based management − Console and Telnet Configuration − SNMP network management − IEEE 802.1Q Tagging VLAN ( 256 VLAN Group ) − IEEE 802.1D Spanning Tree Protocol ( STP ) − Port Trunking supported − IGMP and Sniffer ( Port Mirroring ) supported − Port Priority - 802.1p & TOS ( Type of Service ) supported − Static Address Table for manual address addition − Broadcast Storm Filter function sup
ページ6に含まれる内容の要旨
2. HARDWARE DESCRIPTION This product series provide three different running speed – 10Mbps, 100Mbps, and 1000Mbps in the same switch and automatically distinguish the speed of incoming connection. This section describes the hardware features of these Switches. For easier management and control of the switch, familiarize yourself with its display indicators, and ports. Front panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the
ページ7に含まれる内容の要旨
Power Notice: 1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data loss or network downtime. 2. In some area, installing a surge suppression device may also help to protect your switch from being damaged by unregulated surge or current to the Switch or the power adapter. 2.3 Hardware Installation
ページ8に含まれる内容の要旨
3.WEB-BASED MANAGEMENT This chapter describes how to manage the Switch through the at-hand browser like Internet Browser IE 4.0 or Netscape Communicator 4.x or above. Please check the JAVA applet is enabled in your browser’s option or preference. 3.1 Configuration The management function of this interface runs as an unsigned Java applet. As a result, your browser’s security setting should be set as following: • For Netscape 4 or later: 1. Click on Edit 2. Pick up Preferences item
ページ9に含まれる内容の要旨
Figure 3-1 : Password Screen The default user name and password is "root". After the password is entered you will see the main menu screen. Figure 3-2: The start up screen of MGSW-2402 Web Page 3.3 Home The Home page displays the configuration of the MGSW-2402 Intelligent Switch. System Name An administratively-assigned name of the managed unit System Location The physical location of this managed unit System Contact The contact person for this managed unit. System Up Time Th
ページ10に含まれる内容の要旨
3.4 Modules Modules page shows the modules that have installed into the MGSW-2402-Slot Intelligent Switch. There are fixed 24x 10/100 Base-TX ports in Module 0, and another 2 slot ( module 1 and module 2 ) are used for expansion. In the following example, 1-port Gigabit 1000Base-SX ( LX ) Fiber Module, and 4-port 100Base-FX (ST) Fiber Module are installed into the Switch. Figure 3-3 The Modules Page 3.5 Ports Inside Ports page, you can enable/disable each port, configure Speed/Dupl
ページ11に含まれる内容の要旨
3.6 Statistics The Statistic page displays the detailed information about each port. You can compare and evaluate throughput or other port parameters. All screen data is updated automatically and you can also update the data manually. Figure 3-5 The Statistics Page 3.7 VLAN A VLAN ( Virtual LAN ) is a group of switch ports designated by the switch as belonging to the same broadcast domain. This feature allows workgroup to be defined on the basis of their logical location instead of
ページ12に含まれる内容の要旨
Figure 3-6 The VLAN Page In the VLAN management window, you will see 2 VLANs in the page. To select a certain VLAN, you can do the following: Press ">>" button to display the next two VLANs Press "<<" button to display the previous two VLANs Press ">>|" button to display the last two VLANs Press "|<<" button to display the first two VLANs Enter the VLAN index in the "VLAN" edit box then press "Go to" button You can add, edit and remove port members of each VLAN and then finally pre
ページ13に含まれる内容の要旨
You can add, edit and remove port members of each trunk and then press "Apply" button after you have finished configuring the trunks you need. ( Note: Make sure trunking ports are in the same VLAN group. ) 3.9 STP (Spanning Tree Protocol) Spanning tree is a link management protocol that provides path redundancy while preventing undesirable loops in the network. For Layer 2 Ethernet network to function properly, only one active path must exist between two stations. The spanning-tree
ページ14に含まれる内容の要旨
3.10 Port Security Port Security allows you to restrict specific MAC addresses to reside in some port. For example, a dummy hub is attached to some port for extension, and you just only allow 2 users to access this port at the same time, you can use the port security window to set the parameters. Figure 3-9. The Port Security page To restrict the number of MAC address to reside in a port, you must do the following : Click the “ Enable “ checkbox for that port. IF the “ Enable “checkb
ページ15に含まれる内容の要旨
Figure 3-10. Port Priority – 802.1p page Programmable Mapping of 802.1p to Internal Priority The received packets with 802.1q tag are assigned priority according to a flexible and programmable mapping of the 802.1p user-priority tag (3 bits, value from 0 to 7) to the internal priority queue. The default is to assign a packet to high priority queue when the 802.1p user-priority tag is 4 to 7, and to low priority queue when the 802.1p user-priority tag is 0 to 3. Please check the corres
ページ16に含まれる内容の要旨
3.13 IGMP Multicasting is used to support real-time applications such as video conferencing or streaming audio. IGMP ( Internet Group Management Protocol ) allow you to query for any attached hosts who want to receive a specific multicast service. The switch looks up the IP Multicast Group used for this service and adds any port which received a similar request to that group. It then propagates the service request on to any neighboring multicast switch to ensure that it will continue to
ページ17に含まれる内容の要旨
Static addresses are manually entered into the Static Address Table. 1. Enter the MAC address in the MAC Address field (ex. 00-00-00-00-00-01) and VLAN ID (default is 1) 2. Select the Module and Port you want to associate with this entry with from the Port drop-down box. 3. Click <
ページ18に含まれる内容の要旨
3-15 The Port Mirroring page If you want to monitor all receive and transmit packets of one port. You can do the following: Choose the monitored port in " Mirror Source Port " choice box in the corresponding mirror source module. Only one port can be monitored in one module at the same time. Choose the corresponding target module, port in "Mirror Target Module" and "Mirror Target Port" choice box. Click the corresponding "Enabled" check box. Press "Apply" button 3.17 IP Config You
ページ19に含まれる内容の要旨
Enter the same password in "Password" and "Confirm Password" edit box Press the "Apply" button You should reboot system to let your settings take effect if you have changed one of the IP address, subnet mask and default gateway. 3.18 SNMP You can manage the Switch using third-party’s SNMP ( Simple Network Management Protocol ) agent. Access rights to the SNMP agent are controlled by community strings. To set system name, system location and system contact, you can type t
ページ20に含まれる内容の要旨
Figure 3-18 Save & Reboot page 3.20 Upgrade You can on-line upgrade the firmware of the managed unit. The following steps is needed to upgrade the firmware: Use HTTP or FTP to download the new version firmware from our website. Enter password in the "Password" edit box. Enter the file downloaded in the "File Path" edit box. (You can use "Browse" button to select the file.) Press the "Upgrade" button. After you have successfully upgraded the new firmware, please reboot th
