ページ1に含まれる内容の要旨
10/100Mbps Desktop
Fast Ethernet Switch
SW-504 / SW-804
User's Manual
ページ2に含まれる内容の要旨
Trademarks Copyright © PLANET Technology Corp. 2007. Content subjects to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particul
ページ3に含まれる内容の要旨
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at its own expense. CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous
ページ4に含まれる内容の要旨
Table of Contents 1. INTRODUCTION ........................................................................ 5 1.1 Package Contents ............................................................... 5 1.2 How to Use This Manual ..................................................... 5 1.3 Product Features ................................................................. 6 1.4 Product Specifications ......................................................... 7 2. INSTALLATION ........................
ページ5に含まれる内容の要旨
1. INTRODUCTION 1.1 Package Contents Check the contents of your package for following parts: ● Desktop Fast Ethernet Switch x 1 ● User’s manual x 1 ● Power adapter x 1 If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair. 1.2 How to Use This Manual This Desktop Fast Ethernet Switch User Manual is st
ページ6に含まれる内容の要旨
1.3 Product Features ● Comply with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX ● 5/8-Port 10/100Mbps Auto-Negotiation ports - 10/20Mbps (Half- duplex), 100/200Mbps (Full-duplex) Auto-sensing ● Compact size design for wall mount or desktop placement ● High performance Store-and-Forward Switching Architecture ● Runt and CRC filtering ● Flow control (Back Pressure) supports in half-duplex mode ● 1K MAC Address Table, automatically learning and aging ● LED indicators array for easy diagnostic
ページ7に含まれる内容の要旨
1.4 Product Specifications Model SW-504 SW-804 Hardware Specification 5 10/100Base-TX 8 10/100Base-TX RJ-45 Network Ports RJ-45 MDI/MDI-X ports MDI/MDI-X ports Dimensions 184 x 110 x 30mm (W x D x H) Weight (KG) 0.17 KG Power External Power adapter DC 9V 700 mA Requirement Switch Specification Switch Store-and-Forward Architecture Address Table 1K entries, auto learning/ageing Switch 0.74Mpps 1.19Mpps Throughput Switch Fabric 1Gbps 1.6Gbps Shared Buffer 384K 768K Flow Control IEEE 802.3x fu
ページ8に含まれる内容の要旨
2. INSTALLATION This section describes the functionalities of the Desktop Fast Ethernet Switch’s components and guides how to install it on the desktop. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. 2.1 Product Description With concepts of “Easy to Install and use”, “Compact-sized design”, and “Simple troubleshooting”, PLANET SW-504/SW-804 provides cost-conscious business and home users with the foundation of an integrated system of small-
ページ9に含まれる内容の要旨
2.1.2 Switch Front Panel Figure 2-1 & 2-2 show the front panel and rear panel of SW-504 Figure 2-1 SW-504 front panel Figure 2-2 SW-504 rear panel Figure 2-3 & 2-4 show the front panel and rear panel of SW-804 SW-804 LNK/ACT 1 2 3 4 5 6 7 8 Figure 2-3 SW-804 front panel
ページ10に含まれる内容の要旨
Figure 2-4 SW-804 rear panel 2.1.3 LED Indicators LED Color Function Lights to indicate that the Switch is powered PWR Green on. Lit: indicate the link through that port is successfully established. LNK/ACT Green Blink: indicate that the Switch is actively sending or receiving data over that port. Power Notice: 1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all the time, please consider using UPS (Uninterrupted Power
ページ11に含まれる内容の要旨
2.2.1 Desktop Installation To install the Switch on desktop, simply follow the next steps: Step1: Attach the rubber feet to the recessed areas on the bottom of the Switch. Step2: Place the Switch on desktop near a DC power source. Step3: Keep enough ventilation space between the Switch and the surrounding objects. When choosing a location, please keep in mind the environmental restrictions discussed in Chapter 1, Section 1.4 Product Specification. Note Step4: Connect your Switch to network
ページ12に含まれる内容の要旨
3. SWITCH OPERATION 3.1 Address Table The Switch is implemented with an address table. This address table composed of many entries. Each entry is used to store the address information of some node in network, including MAC address, port no, etc. This information comes from the learning process of Ethernet Switch. 3.2 Learning When one packet comes in from any port, the Switch will record the source address, port no. And the other related information in address table. This information will
ページ13に含まれる内容の要旨
The Ethernet Switch scans the destination address from the packet- header, searches the routing table provided for the incoming port and forwards the packet, only if required. The fast forwarding makes the switch attractive for connecting servers directly to the network, thereby increasing throughput and availability. However, the switch is most commonly used to segment existing hubs, which nearly always improves overall performance. An Ethernet Switching can be easily configured in any Et
ページ14に含まれる内容の要旨
4. TROUBLESHOOTING This chapter contains information to help you solve issues. If Desktop Fast Ethernet Switch is not functioning properly, make sure the Desktop Fast Ethernet Switch was set up according to instructions in this manual. Some stations cannot talk to other stations located on the other port Solution: The address table may contain older information than of the address table of that node. Please power down to refresh the address information. Performance is bad Solution: Check t
ページ15に含まれる内容の要旨
Appendix A A.1 Switch’s RJ-45 Pin Assignments When connecting your Desktop Fast Ethernet Switch to another switch, a bridge or a hub, a straight or crossover cable is necessary. Each port of the Switch supports auto-MDI/MDI-X detection. That means you can directly connect the Switch to any Ethernet devices without making a crossover cable. The following table and diagram show the standard RJ- 45 receptacle/ connector and their pin assignments: RJ-45 Connector pin assignment MDI-X MDI Contact
ページ16に含まれる内容の要旨
coded. The following shows the pin allocation and color of straight cable and crossover cable connection: Figure A-1 Straight-Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network. 1
