ページ1に含まれる内容の要旨
10/100/1000Mbps
Managed Stackable Switch
SGSW-4802
User’s Manual
ページ2に含まれる内容の要旨
Trademarks Copyright © PLANET Technology Corp. 2003. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a
ページ3に含まれる内容の要旨
TABLE OF CONTENTS 1. Introduction.........................................................................................................................................1 1.1 Checklist ..........................................................................................................................................1 1.2 About the Switch..............................................................................................................................1 1.3 Features .......
ページ4に含まれる内容の要旨
3.21 Save & Reboot.............................................................................................................................34 3.21.1 Save......................................................................................................................................34 3.21.2 Backup ..................................................................................................................................34 3.21.3 Restore .......................................
ページ5に含まれる内容の要旨
1. INTRODUCTION 1.1 Checklist Check the contents of your package for following parts: l SGSW-4802. l User's manual CD. l Power cord. l 19” rack mounting kit. l RS-232 cable. l Quick Installation Guide. If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair. 1.2 About the Swit
ページ6に含まれる内容の要旨
w Internal power supply w Auto MDI/ MDI-X on each port w Network management configuration: - Web-based management - Console and Telnet Configuration - SNMP network management - IEEE 802.1Q Tagging VLAN (32 VLAN Groups) - Port Trunking supported - IEEE 802.1D Spanning Tree Protocol (STP) - IGMP and Sniffer (Port Mirroring) supported - Port Priority - 802.1p supported - MAC / IP Address search - Port security control (MAC address filtering) - Virtual stacking up to 16 units - Broad
ページ7に含まれる内容の要旨
VLAN IEEE 802.1Q VLAN, up to 32 VLANs supported IEEE 802.1p QoS support with 2 priority queue using WFQ (Weighted Fair QoS Queuing) IGMP Multicast Filtering Passive snooping on IGMP Query/Report messages Port trunking Up to 4 ports can be combined into a fat pipe Port Mirroring 1 mirroring port to monitor several mirrored ports Standards Conformance Regulation Compliance FCC Part 15 Class A, CE IEEE 802.3 (Ethernet) IEEE 802.3u (Fast Ethernet), IEEE 802.3z (1000Base-S
ページ8に含まれる内容の要旨
2. HARDWARE DESCRIPTION This product series provide three different running speed – 10Mbps, 100Mbps, and 1000Mbps in the same switch and automatically distinguish the speed of incoming connection. This section describes the hardware features of SGSW-4802. For easier management and control of the switch, familiarize yourself with its display indicators, and ports. Front panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the switch
ページ9に含まれる内容の要旨
2.2 Rear Panel The rear panel of the Switch indicates an AC inlet power socket, which accepts input power from 100 to 240VAC, 50-60Hz. 100- 240V AC 50/ 60Hz SGSW-4802 Switch rear panel Power Notice: 1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all the time, please consider using UPS (Uninterrupted Power Supply) for your de- vice. It will prevent you from network data loss or network downtime. 2. In some area, i
ページ10に含まれる内容の要旨
minal program may be a good choice. It can be accessed from the Start menu. Click START, then Programs, Accessories and then Hyper Terminal. MS-DOS based terminal program such as PC-PLUS, PROCOMM, can also make the connection with the device built-in software. The COM port should be configured as: ¨ Baud : 38400 ¨ Parity : None ¨ Data bits : 8 ¨ Stop bits : 1 ¨ Flow Control: none Once the terminal has connected to the device, power on the device. The terminal will display that
ページ11に含まれる内容の要旨
To setup the IP address, please use “sys set ip” command in the following format: sys set ip For example, to configure the switch with the following IP settings: IP Address: 192.168.0.2 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.0.254 Press input the following command and press button: sys set ip 192.168.0.2 255.255.255.0 192.168.0.254 If the IP is successful configured, the switch will automatically restart as the fol
ページ12に含まれる内容の要旨
3. WEB-BASED MANAGEMENT 3.1 Configuration As well as the menu-driven system configuration program, the agent module provides an embedded HTTP Web agent. This agent can be accessed by any computer on the network that using a standard Web browser (Internet Explorer 5.0 or above, or Netscape Navigator 4.5 or above). Using the Web browser management interface you can configure a switch and view statistics to monitor network activity. The Web interface also provides access to a range of S
ページ13に含まれる内容の要旨
3.2 Web Pages To access the Web-browser interface you must first enter the password. The default password is "admin" You will see the following screen comes out on the Web browser program: Figure 3-1: SGSW-4802 login Web Page After the password is entered you will see the main menu web screen of SGSW-4802. Figure 3-2: The start up screen of SGSW-4802 Web Page 3.3 Port Config This section allows you to have an easy access in configuring the ports of the management Switch. Notice tha
ページ14に含まれる内容の要旨
Figure 3-3: The Port Config Web Page Choose Port You can choose a port either by clicking on the picture or by selecting it at the “Choose Port” field. Speed/ Duplex Speed/ Duplex is to select the operation mode of chosen port. The options are as: ‘Auto’: Auto negotiation ‘10Mbps HD’: 10 Base-T Half Duplex ‘10Mpbs FD’: 10Base-T Full Duplex ‘100Mpbs HD’: 100Base-TX Half Duplex ‘100Mbps FD’: 100Base-TX Full Duplex Broadcast Rate Limit This function sets broadcast limit to the desire
ページ15に含まれる内容の要旨
dresses. It should be noted that if the cpu port (i.e. the switch port connected to the management workstation) is disabled, without doubt, the communication link between user and the switch will not proceed further. It is recommended to locate the link your PC used before disable the port state. Flow Control This feature enables or disables the Flow Control function of the port. Flow control can eliminate frame loss by "blocking" traffic from end stations or segments connected directly
ページ16に含まれる内容の要旨
3.5 Trunk config The SGSW-4802 provides 2 trunk groups and maximum up to 4-ports per trunk. Port Trunking is the ability to group together several switch ports to increase the bandwidth between the management switch and other switch. This is an inexpensive method to increase throughput between switches (or to servers). We define the Port Trunking as the ability to group a set of ports into a single logical link. The port trunk acts as single link between switches. It doesn’t create a loop
ページ17に含まれる内容の要旨
3.6 Advanced Configuration The available options in “Advanced menu” are: STP Config The Spanning Tree Setup Screen IGMP Config The IGMP Setup Screen Stack Config The Stack Setup Screen SNMP Config The SNMP Setup Screen RMON Statistics Show RMON statistics information Port Security The Port Security Setup Screen MirrorPort Config The Mirror Port Setup Screen Aging Control The Aging Control Setup Screen Address Search The Address Search Setup Screen 3.7 STP Config The STP Config p
ページ18に含まれる内容の要旨
3.7.1 STP Port This function allows assigning Path Cost value and Priority level on each port of SGSW-4802. Please refer to the detail description of Path Cost and Priority and setup procedures shown as below. Description of Parameters Bridge Port This option shows the port of the bridge that connects to the root bridge. Path Cost The STA algorithm to determine the best path between devices uses this parameter. Therefore, lower values should be assigned to ports attached to
ページ19に含まれる内容の要旨
3.7.2 STP Bridge This function provides to have a clearer view in Spanning Tree parameters of SGSW-4802. The STP Bridge screen in Figure 3-7 appears. Figure 3-7: The STP Bridge Web Page Description of Parameters STP State When STP is enabled, it will dynamically detect network looping owing to mis-configuration of the network topology. The redundant connectors will be disabled to avoid looping of packets. Looping would often result in flooding of broadcast packets, halting the norma
ページ20に含まれる内容の要旨
Setup Procedures Step 1: Select Spanning Tree state option, either to enable or disable it. Step 2: Set Root Priority from 0 s – 65535 s, and Hello Time from 1 s – 10 s. Step 3: Key in the Forward Delay Time, Maximum Age and Hello Time. Step 4: Click “Apply” button and save it if everything is OK. The screen is divided into two sections. Current Spanning Tree Root section displays the ! read-only Spanning Tree settings for the current root switch and the parameters this NOTE switc
