ページ1に含まれる内容の要旨
10/100/1000Mbps
Intelligent Gigabit / Fast Ethernet Switch
WGSD-1020
User’s Manual
ページ2に含まれる内容の要旨
Trademarks Copyright © PLANET Technology Corp. 2003. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a p
ページ3に含まれる内容の要旨
TABLE OF CONTENTS 1. INTRODUCTION .......................................................................................................................................1 1.1 CHECKLIST..............................................................................................................................................1 1.2 ABOUT THE SWITCH.................................................................................................................................1 1.3 FEATURES..
ページ4に含まれる内容の要旨
APPENDIX A NETWORKING CONNECTION.............................................................................................86 A.1 SWITCH‘S RJ-45 PIN ASSIGNMENTS ......................................................................................................86 A.2 10/100MBPS, 10/100BASE-TX .............................................................................................................86 A.3 RJ-45 CABLE PIN ASSIGNMENT ......................................................
ページ5に含まれる内容の要旨
1. INTRODUCTION 1.1 Checklist Check the contents of your package for following parts: ● WGSD-1020 ● User's manual CD ● RS-232 cable ● Power cord ● Quick installation Guide If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair. 1.2 About the Switch The Ethernet Switch is equipped with
ページ6に含まれる内容の要旨
◆ Support IGMP V1.0 ◆ Support LACP IEEE 802.3ad Port Trunking ◆ Support MAC address filtering ◆ Complies with IEEE 802.1d Spanning Tree ◆ Support port sniffer function ◆ SNMP agent: - MIB 2 (RFC-1213) - Bridge MIB (RFC-1493) - Ethernet MIB (RFC-1643) - RMON MIB (RFC-1493) – statistics, history, alarms, and events ◆ Support to handle up to 1522 bytes packet ◆ One RS232 port as local control console ◆ Telnet remote control console ◆ Web browser based on HTTP server ◆ TFTP/X
ページ7に含まれる内容の要旨
2. HARDWARE DESCRIPTION This section describes the hardware features of the Giga Switch. For easier management and control of the switch, familiarize yourself with its display indicators, and ports. Front panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the Switch, read this chapter carefully. 2.1 Front Panel The unit front panel provides a simple interface monitoring the switching. It includes a power indicator for eac
ページ8に含まれる内容の要旨
1000Base-T LNK/ACT LED Color Function LNK / ACT Green Lit: indicate the link through that port is successfully established. Blink: indicate that the switch is actively sending or receiving data over that port. 1000/100 LED Color Function 1000 Orange Lit: indicate that connection made through the corresponding port is running at 1000Mbps. Lit: indicate that connection made through the 100 Green corresponding port is running at 100Mbps. FDX
ページ9に含まれる内容の要旨
2.3 Hardware Installation 2.3.1 Before start up Before your installation, please refer to the followings for your cabling: 100Base-TX All 100Base-TX ports come with auto-negotiation capability. They automatically support 100Base-TX and 10Base-T networks. Users only need to plug a working network device into one of the 100Base-TX ports, then turn on the Switch. The port will automatically runs in 10Mbps, 20Mbps, 100Mbps or 200Mbps after the negotiation with the connected device. 1000Ba
ページ10に含まれる内容の要旨
Figure 3. End node or Hub or Switch connection Notice: Cable distance for Switch The cable distance between Ethernet Switch and hub/PC should not exceed 100 meter for UTP/STP cable. Make sure the wiring is correct It can be used Category 3/4/5 cable in 10 Mbps operation. To reliably operate your network at 100Mbps and 1000Mbps, you must use an Unshielded Twisted-Pair (UTP) Category 5 cable, or better Data Grade cabling. While a Category 3
ページ11に含まれる内容の要旨
3. SWITCH MANAGEMENT This chapter describes how to manage the Switch. Topics include: - Overview - Management methods - Assigning an IP address to the Switch - Logging on to the Switch 3.1 Overview The Switch provides a user-friendly, menu driven console interface. Using this interface, you can per- form various switch configuration and management activities, including: - Assigning an IP address - Configuring Switch settings - Display console port information - Configuring each
ページ12に含まれる内容の要旨
3.2.2 Remote Console Management You can manage the Switch remotely by having a remote host establish a Telnet connection to the Switch via an Ethernet or modem link. Using this management method: The Switch must have an Internet Protocol (IP) address The Remote Console Management interface is identical in appearance and functionality to the Local Console Management interface described in the previous section. 3.2.3 Web Management You can manage the Switch remotely by having a remote ho
ページ13に含まれる内容の要旨
4. CONSOLE INTERFACE 4.1 CONNECT TO PC RS-232 serial cable Use the bundled RS-232 serial cable and attach the 9-pin female connector to the male connector on the switch. Plug the other side of this cable to your PC. Hyper Terminal In Windows 95/98/2000/XP, launch “HyperTerminal”, create a new connection, and adjust settings as below: § Emulation: VT-100 compatible § Baud per second: 9600 § Data bits: 8 § Parity: None § Stop bits: 1 § Flow Control: None To gain a demo, p
ページ14に含まれる内容の要旨
4.2 Login in Login is required to access the command console after the self-test completes successfully. The factory default user name is "admin" without password. You may change it in the System Menu. To access to the Main Menu, please always enter the correct user name. (See Figure 4-2) Figure 4-2 WGSD-1020 login screen 4.3 Main screen After login the WGSD-1020, the main screen shows as below.
ページ15に含まれる内容の要旨
4.3.1 Status and Counters From the Switch main menu screen (see Figure 4-3), highlight Status and counters and press enter. The Status and Counters sub-screen in Figure 4-4 appears. Figure 4-4 Status and Counters sub-screen This sub-menu contains four items: Port Status: Please refer to chapter 4.3.1.1. Port Counters: Please refer to chapter 4.3.1.2 System Information: Please refer to chapter 4.3.1.3 Main Menu:
ページ16に含まれる内容の要旨
4.3.1.2 Port Counters Display the traffic counters of each port on WGSD-1020. Figure 4-6 Port Counters screen 4.3.1.3 System Information Display the Switch information. Figure 4-7 System Information screen - 12 -
ページ17に含まれる内容の要旨
4.3.2 Switch Static Configuration From the Switch Static Configuration screen (see Figure 4-8), highlight Switch Static Configuration and press Enter. The Switch Static Configuration sub-screen in Figure 4-9 appears. Figure 4-8 Switch Static Configuration screen Figure 4-9 Switch Static Configuration sub-screen This sub-menu contains eight items: Administr
ページ18に含まれる内容の要旨
4.3.2.1 Administration Configuration Figure 4-10 Device Configuration screen This sub-menu contains five items: Device Information: please refer to chapter 4.3.2.1.1 IP Configuration: please refer to chapter 4.3.2.1.2 Change Username: please refer to chapter 4.3.2.1.3 Change Password: please refer to chapter 4.3.2.1.4 Previous Menu: return to previous menu 4.3.2.1.1 Device Information Display the Device information.
ページ19に含まれる内容の要旨
4.3.2.1.2 IP Configuration Press ”Edit” to modify the IP address, Subnet Mask and Gateway. Figure 4-12 IP Configuration screen Press “Tab” to move the cursor to IP Address, Subnet Mask and Gateway to input new value. After setup completed, press “ctrl-A” to save the current configuration. The following screen in Figure 4-13 appears. Figure 4-13 IP Configuration save successful screen You need to reboot the Switch to take effect of your IP configurati
ページ20に含まれる内容の要旨
4.3.2.1.3 Change Username Press “Edit” to input the new username and choose “save” to save the current configuration. The following screen in Figure 4-14 appears. Figure 4-14 Edit Username Configuration screen Figure 4-15 Username Configuration save successfully screen - 16 -
