ページ1に含まれる内容の要旨
EM-200
User Manual
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Disclaimer The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warran
ページ4に含まれる内容の要旨
About this manual This manual is intended for system administrators who are familiar with setting up a new system and installing an operating system. The manual consists of the following sections: Chapter 1 Getting Started: This section covers unpacking and checking the package contents, identifying components, installing the battery pack, charging the battery and powering on. Chapter 2 BIOS Setup Utility: The BIOS chapter provides information on navigating and changing settings in the
ページ5に含まれる内容の要旨
Revision history Version 1.0, August 2009 iii
ページ6に含まれる内容の要旨
TABLE OF CONTENTS CHAPTER 1 GETTING STARTED ................................................ 1 Unpacking the machine..................................................................................1 Checking the package contents ....................................................................2 Identifying components .................................................................................3 Installing the battery pack ................................................................
ページ7に含まれる内容の要旨
CHAPTER 1 GETTING STARTED This chapter describes the procedures from unpacking the EM-200, to powering it on. The following topics are described. • Unpacking the machine on page 1 • Checking the package contents on page 2 • Identifying components on page 3 • Installing the battery pack on page 8 • Charging the battery pack on page 9 • “Powering on” on page 10 Unpacking the machine The machine and cable accessories are packed in a cardboard carton with foam padding for protection during
ページ8に含まれる内容の要旨
Checking the package contents After you unpack the device, check that the following items are included. Metal Stylus EM-200 Battery QSG Driver CD with drivers Quick Start Guide and the user manual PDF file. Protection pack Power cord AC adapter If any item is missing or appears damaged, contact your dealer immediately. 2 C H A P T E R 1 G E T T I N G S TA R T E D
ページ9に含まれる内容の要旨
Identifying components This section describes the parts and connectors on the machine. Front view 1 2 3 4 5 6 7 Figure 1.2 Front view 8 9 Component Description 1 Power indicator 2 Battery charging indicator 3 HDD status indicator 4 WiFi On/ Off indicator 5 Bluetooth On/ Off indicator 6 3.5G LAN On/Off indicator (optional) 7 Built-in Microphone 8 Camera (optional) 9 10.1-inch touch panel 3
ページ10に含まれる内容の要旨
Left view 1 2 3 4 5 6 Figure 1.3 Left view Component Description 1 5-in-1 media card slot 2 Express card 34 slot 3 USB port 4 Power button 5 RJ45 LAN jack 6 DC IN 4 C H A P T E R 1 G E T T I N G S TA R T E D
ページ11に含まれる内容の要旨
Right view 1 2 3 4 5 Figure 1.4 Right view Component Description 1 VGA port 2 USB port 3 Ventilation hole 4 Headphone jack 5 Microphone jack 5
ページ12に含まれる内容の要旨
Rear view 3 1 2 1 3 Figure 1.5 Rear view Component Description 1 Speaker 2 Battery pack 3 Charger pin: connect to a cradle for charging the battery. Do not short-circuit the 3 charger pins. A short-circuit may cause damage to the machine and present risks for electric shock or fire. IMPORTANT 6 C H A P T E R 1 G E T T I N G S TA R T E D
ページ13に含まれる内容の要旨
Bottom view 2 1 1 3 4 5 6 7 Figure 1.6 Bottom view Component Description 1 Mounting hole 2 Camera (optional) 3 Battery lock switch 4 Memory, WiFi module, Bluetooth module and 3.5G LAN module (optional) slots 5 Battery pack 6 HDD compartment 7 Battery release latch 7
ページ14に含まれる内容の要旨
Installing the battery pack 1. Overturn the EM200 so that the bottom is facing up toward you, as shown in the right. Slide the battery release latch to the unlock position. 2. Align EM200 battery compartment pins to the battery connector. Slightly slide and press the battery pack into the compartment until the battery lock switch is bounced back. 3. As shown in the right, slide the battery release latch to the lock posi- tion. 8 C H A P T E R 1 G E T T I N G S TA R T E D
ページ15に含まれる内容の要旨
Charging the battery pack Plug the AC adapter power cord into an electrical outlet, then connect the DC plug of the adapter cable to the EM-200. It takes approximately 2–4 hours to fully char ge the battery for the first time. Subsequent char ges might take longer. Charge the battery within a temperature range 0˚C to 45˚C. NOTE To protect and prolong the life of the battery, do not charge it for 24 hours or longer at a time. IMPORTANT Please make sure to perform 3 complete full charge and dis
ページ16に含まれる内容の要旨
Powering on The power button located on the left side of the EM200, press the power button the turn it on. To force power off , long press the power button for 4~5 seconds. NOTE 10 C H A P T E R 1 G E T T I N G S TA R T E D
ページ17に含まれる内容の要旨
CHAPTER 2 BIOS SETUP The primary function of the BIOS (Basic Input and Output System) is to identify and initiate component hardware. The BIOS parameters are stored in non-volatile BIOS memory (CMOS). CMOS contents don’t get erased when the computer is turned off. The following topics are described in this chapter. • About the Setup Utility on page 11 • Using the USB keyboard on page 11 • Main Menu on page 14 • Advanced Menu on page 15 • Security Menu on page 19 • Boot Menu on page 2
ページ18に含まれる内容の要旨
Entering the Setup Utility Press the F2 key during booting to access the BIOS Setup Utility: InsydelH2O Setup Utility Main Advanced Security Boot Exit Item Specific Help System BIOS Version GA-D1USB28 F04 Processor Type Intel(R) Atom(TM) CPU N270 @ 1.66GHz System Bus Speed 533 MHz System Memory Speed 533 MHz Cache RAM 0512 KB Total Memory 1024 MB System Time [18:47:25] System Date [06/21/2009] F1 Help ↑↓ Select Item F7/F8 Change Values F9 Setup Default ESC Exit ←→Select Menu
ページ19に含まれる内容の要旨
Using BIOS When you start the Setup Utility, the main menu appears. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing . Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for information. Some options (marked with a triangle ►) lead to submenus t
ページ20に含まれる内容の要旨
Main Menu Press right/left arrow key to select the Main menu, which displays the following screen: InsydelH2O Setup Utility Main Advanced Security Boot Exit Item Specific Help System BIOS Version GA-D1USB28 F04 Processor Type Intel(R) Atom(TM) CPU N270 @ 1.66GHz System Bus Speed 533 MHz System Memory Speed 533 MHz Figure 2.2 Main menu Cache RAM 0512 KB Total Memory 1024 MB System Time [18:47:25] System Date [06/21/2009] F1 Help ↑↓ Select Item F7/F8 Change Values F9 Setup Default E
