ページ1に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 2
Model 800-EFM
External Feature Module
User’s Guide
800-EFM
Note: The 800-EFM External Feature Module can be
set as a music on hold adapter, external paging
adapter, or a door intercom adapter
Please read before using feature module.
ページ2に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 3 Getting Started Getting Started Congratulations! You’ve purchased a TMC Model 800-EFM External Feature Module that meets the highest standards for quality and convenience in the Small Office/Home Office environment. To get the most from your Feature Module, please take time to read this guide thoroughly. IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce t
ページ3に含まれる内容の要旨
Part A EXT v23 091302 in order for booklet.qxd 9/14/2002 4:04 PM Page 6 Getting Started Before you begin . . . The TMC Model 800-EFM External Feature Module is designed for easy installation in your home or office. However, it is important that you follow these few simple guidelines: - Take a few minutes to read this manual so that you thoroughly understand the instructions to be followed for proper installation of your Feature Module. - This User’s Guide provides easy to understand directio
ページ4に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 5 Table of Contents Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i Reference Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v Section 1A - Installing Your External Paging Adapter . . . . . . . . . . . . .1-7 Step 1: Connect Line Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Step 2: Set DIP Switches to Proper Postions
ページ5に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 6 Table of Contents Section 3A - Installing Your Music On Hold Adapter . . . . . . . . . . . . . .25-29 Step 1: Connect Line Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Step 2: Set DIP Switches to Proper Positions . . . . . . . . . . . . . . . . .27 Step 3: Connect Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Step 4: Connect Music Source . . . . . . . . . . . . . . . . . . . . . . . .
ページ6に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 7 Reference Drawing Paging Volume Control Knob for External Paging Adapter AC Adapter Jack Music Volume Control Knob for Music on Hold Adapter Strain Relief Tab Dip Switches Jacks for connection Music Input Jack to Wall Status Indicator Lamp for Music on Hold Adapter Jacks for connection to a Phone v
ページ7に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 8 Installing Your External Paging Adapter Page Section 2 Step 1: Connect Line Cord 1A 3 Step 2: Set DIP Switches to Proper Positions Installing 4 Step 3: Connect Power Cord 5 Step 4: Connect Wiring Block Your to External Paging Adapter External 6 Step 5: Connect Amplifier and Speaker to Wiring Block Paging Adapter 7 Step 6: Adjust Speaker Volume to Desired Level 1
ページ8に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 9 Installing Your External Paging Adapter Step 1: Connect Line Cord 1 Connect Line Cord Connect one end of a long telephone line cord L1/L2 to the jack on the back of the feature module labeled L1/L2. Connect the other end to a jack Lines labeled Lines 1 & 2 or to a jack labeled line 1. 1&2 PLEASE NOTE: You must be sure to connect the cord to LINE 1. It does not matter if it is also connected to line 2. Note also that you can insta
ページ9に含まれる内容の要旨
Part A EXT v23 091302 in order for booklet.qxd 9/14/2002 4:04 PM Page 18 Installing Your External Paging Adapter Step 2: Set DIP Switches to Proper Positions Set Switches 7-8 IMPORTANT: Make Set switch 7 in the up position and switch sure that switch 7 is 8 in the down position to set this feature set in the up position and switch 8 is set in module as an External Paging Adapter. the down position. Set Switch 5 The setting of this DIP switch determines whether your External Paging Adapter wil
ページ10に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 11 Installing Your External Paging Adapter Step 3: Connect Power Cord 1 Connect Power Cord to Module Plug the AC power cord into the adapter jack at the rear of the Feature Module. Thread the power cord around the strain relief tab. 2 Connect Power Cord to Wall Outlet Plug the AC adapter into an electrical outlet not controlled by a wall switch. 3 Make Sure that Status Indicator lamp is Blinking This indicates that the feature mod
ページ11に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 12 Installing Your External Paging Adapter Step 4: Connect Wiring Block to External Paging Adapter 1 Locate 8-wire Cord Find the 8-wire cord which was enclosed with your External Paging Adapter. Note that this is a black cord which is approximately 6 inches long. Note that you must use this cord, as any other cord may not work. 2 Connect Cord to Feature Module Plug one end of the 8-wire cord into the jack on the back of your Ex
ページ12に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 13 Installing Your External Paging Adapter Step 5: Connect Amplifier and Speaker to Wiring Block 1 Install Amplifier and Speaker Please follow the installation instructions that came with your amplifier and speaker. Note that you may be installing a speaker with a built-in amplifier. These are called “amplified speakers” or “self-powered speakers”. In this case you would not need an external amplifier. 2 Connect Wiring Block to I
ページ13に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 14 Installing Your External Paging Adapter Step 6: Adjust Speaker Volume to Desired Level 1 Listen to Speaker Volume At the System phone nearest the External Paging Adapter, make an announcement through that external speaker (see page 10 for instructions on doing this). Listen to the vol- ume of your announcement through the speak- er, or ask someone else to make the announcement while you listen to the volume level. 2 Adjust the V
ページ14に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 16 Using Your External Paging Adapter Page Section 10 Operation of your External 1B Paging Adapter 11 Important Points to Note Using Your 12 Troubleshooting Guide External Paging Adapter 9
ページ15に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 17 Using Your External Paging Adapter Operation of your External Paging Adapter To make an announcement through a particular external speaker: You may connect as many External Paging Adapters to your system as you like. Connect each one to a separate amplifier and speaker 1 Press PAGE. and assign each a different station number from 12 to 26 (See page 3) 2 Dial the two-digit station number of the speaker you wish to page. When you w
ページ16に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 18 Using Your External Paging Adapter Important Points to Note You must attach your External Paging Adapter to line 1 for it to function. You may connect up to 15 External Paging Adapters to your system. Connect each one to a separate External Paging speaker and assign each one a differ- ent station number from 12 to 26. You must assign each external paging adapter its own unique station num- ber, and you must make sure that you have
ページ17に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 21 Using Your External Paging Adapter Troubleshooting Guide If you are having difficulty with your External Paging Adapter, DO NOT RETURN IT! You may find your problem and solution listed below. If not, call TMC’s toll-free customer support line at 1-800-TMC-1638, and an expert will walk you through your problem. You may also use this toll-free line if you ever have a question that is not answered in your User’s Guide. The Feature M
ページ18に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 22 Installing Your Door Intercom Adapter Page Section 14 Step 1: Connect Line Cord 2A 15 Step 2: Set DIP Switches to Proper Positions Installing 16 Step 3: Connect Power Cord 17 Step 4: Connect Wiring Block Your to Door Intercom Adapter Door Intercom 18 Step 5: Connect Door Speaker to Wiring Block Adapter 19 Step 6: Connect Doorbell to Wiring Block 20 Step 7: Connect Magnetic Door Strike to Wiring Block (Optional) 13
ページ19に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 25 Installing Your Door Intercom Adapter Step 1: Connect Line Cord 1 Connect Line Cord Connect one end of a long telephone line cord L1/L2 Lines to the jack on the back of the feature module 1&2 labeled L1/L2. Connect the other end to a jack labeled Lines 1 & 2 or to a jack labeled line 1. PLEASE NOTE: You must be sure to connect the cord to LINE 1. It does not matter if it is also connected to line 2. 14
ページ20に含まれる内容の要旨
800-EFM guide for PDF v1 091102.qxd 9/11/2002 2:40 PM Page 26 Installing Your Door Intercom Adapter Step 2: Set DIP Switches to Proper Positions Set Switches 7-8 IMPORTANT: Make Set switch 7 in the down position and sure that switch 7 is switch 8 in the up position to set this fea- set in the down posi- tion and switch 8 is set ture module as a Door Intercom Adapter. in the up position. Set Switches 5-6 (Optional) The setting of these DIP switches deter- mines how many seconds the magnetic 2
