UNICOM Electric Unicom Velocity 10/100/1000Base-T 1000Base-SX/LX Gigabit Ethernet Converter GEP-5300TF-Cの取扱説明書

ページ1に含まれる内容の要旨

For full coverage of your warranty, be sure
to register your product using the enclosed
registration card.
10/100/1000Base-T
1000Base-SX/LX
Gigabit Ethernet Converter
GEP-5300TF-C 1000Base-T/SX (SC/MM/550m)
GEP-5400TF-C 1000Base-T/LX (SC/SM/10km)
Rev. 2.0
908 Canada Court
City of Industry, CA 91748 U.S.A.
Phone: 626.964.7873 or 800.346.6668 Fax: 626.964.7880
www.unicomlink.com e-mail: info@unicomlink.com
USER’S MANUAL
©UNICOM 2009. UNICOM and “A Network Systems Solution” are trademarks of UNICOM

ページ2に含まれる内容の要旨

Package Contents Package contents include the following:
10/100/1000Base-T to 1000Base-SX/LX Converter (Multi-Mode or Single Mode)
DC Power Adapter
User’s Manual
Rack Mount Brackets
Warranty card (not shown) Gigabit User’s Manual Power Adapter Rack Mount Converter Brackets (Multi-Mode or Single Mode) IMPORTANT: If any piece is missing or damaged, please contact your local dealer or reseller for service. For Your Records Product Name: Serial Number: Date of Purchase: Purchased from: Not

ページ3に含まれる内容の要旨

Product Specifications Introduction Congratulations on purchasing a quality UNICOM product. Standard Compliance: IEEE 802.3 10/100/1000Base-T Gigabit Ethernet IEEE 802.3 1000Base-SX/LX Gigabit Ethernet Unicom’s VELOCITY Series represents the newest, most advanced generation of signal conversion technology. Protocol: CSMA/CD Unicom’s Giga Fiber Converter is a cost- effective solution for the Interface: (1) 10/100/1000Base-T, Shielded RJ-45 Jack conversion of 10/100/1000Base-T (Auto MDI/MDIX) and

ページ4に含まれる内容の要旨

Key Features Cabling • Twisted-pair segments can be Unshielded Twisted Pair (UTP) or Standards: IEEE 802.3 10BASE-T Shielded Twisted Pair (STP) cabling. The cable must comply with the IEEE 802.3u 100BASE-TX IEEE 802.3 10/100/1000Base-T standard for Category 5e/6. The IEEE 802.3ab 1000BaseT, cable between the converter and the link partner (switch, hub, IEEE 802.3z 1000BaseSX/LX standards workstation, etc.) must be 100 meters (328 ft.) or less in length. IEEE 802.3x Flow Control and Back pressure

ページ5に含まれる内容の要旨

10/100/1000T SPD 100Base-SX Auto MDI/MDIX Installing Converters into Chassis Hardware Description Follow the steps below to install modular converters into the 10 space The Front Panel Converter Chassis (pn: FEP-593110). The Front Panel of the 10/100/1000T to 1000SX/LX converters A. Remove the blank bracket from the chassis by rotating screw consists of one RJ-45 Port ( Auto MDI/MDIX ) one fiber 1000Base- counterclockwise. Put the blank bracket aside. SX/LX Port and 6 LED Indicators (SPD, LK/ACT

ページ6に含まれる内容の要旨

LED Indicators DIP Switch Description There are six diagnostic LEDs located on the front panel of these The DIP-switch is used to configure operation mode for LLF (Link converters. The LEDs provide real-time information on system status. Lost Forwarding) and operation mode for Copper/Fiber port. The The indicators include SPD, LK/ACT, FDX, Fiber LK/ACT, FDX/COL and default value of Dipswitch is OFF. PWR. The following table provides describes these LEDs: 10/100/1000Base-T to 1000Base-FX converte