ページ1に含まれる内容の要旨
1012606
3-POINT MOUNTING KIT
For Woods BH90-X Backhoe
Tested. Proven. Unbeatable.
SAVE THIS
MANUAL!
Include it with
your Backhoe Manual.
It contains safety,
operation, and repair
part information not
found in other
manuals.
MAN0549
(6/30/2006)
INSTALLATION MANUAL
ページ2に含まれる内容の要旨
TO THE DEALER: ® Assembly and proper installation of this product is the responsibility of the Woods dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Product Registration included with this manual. The customer must sign the registration which certifies that all Dealer Check List items have been completed. The dea
ページ3に含まれる内容の要旨
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Keep hands and body away from pressurized ! lines. Use paper or cardboard, not hands or other LEA EL INSTRUCTIVO! body parts to check for leaks. Wear safety goggles. Si no lee Ingles, pida ayuda a Hydraulic fluid under pressure can easily penetrate alguien que si lo lea para que le skin and will cause serious injury or death. traduzca las medidas de seguridad. Make sure that all operating and service person- nel know that if hydra
ページ4に含まれる内容の要旨
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) � Read Mounting Kit Manual instructions on attaching and removing backhoe and use Always wear relatively tight and belted clothing extreme care. to avoid getting caught in moving parts. Wear � Always stand between rear tire and backhoe sturdy, rough-soled work shoes and protective stabilizer arms or along side of tractor to avoid equipment for eyes, hair, hands, hearing, and head; being tr
ページ5に含まれる内容の要旨
BACKHOE 3-POINT MOUNT INSTALLATION TRACTOR PREPARATION NOTE: For installing this 3-point mounting kit, refer- ence to right, left, forward and rearward directions are determined from the operator’s position in the back- hoe seat. NOTE: Leave all hardware loose until mounting kit has been fit up. 1. Refer to the WOODS BH90-X Backhoe Opera- tor’s Manual for backhoe assembly instructions. 2. Remove the tractor top link and top link storage bracket, if equipped. * Operator’s seat must be located i
ページ6に含まれる内容の要旨
Attach Top Link to Backhoe 1. Attach top link (1) to the main frame using two 1. 1017875 Top link cap screws (7), four hardened flat washers (16), 2. 37670 Double top link and two hex nuts (8). 7. 14334 3/4 NC x 3 HHCS GR5 2. Slide double top link (2) over top link (1) and 8. 1450 3/4 NC Hex nut secure using two cap screws (10) and lock huts 10. 34157 7/8 NC x 3-1/2 HHCS GR5 (12). See Figure 3. 12. 34194 7/8 NC Lock nut NOTE: To estimate the overall length of the two 16. 57798 3/4 Hardened fl
ページ7に含まれる内容の要旨
Attach Offset Bars to Backhoe 3. Attach offset bars (3) to right and left rear brack- ets using sleeves (15), cap screws (10), and lock nuts (12). Do not tighten nuts at this time. 4. Swing offset bars up and attach it to the double top link bar using cap screw (11) and lock nut (12). See Figure 4. 3. 37679 Offset bar 10. 34157 7/8 NC x 3-1/2 HHCS GR5 11. 34163 7/8 NC x 5 HHCS GR5 12. 34194 7/8 NC Lock nut 15. 38696 Sleeve, .88 x 1.25 x 1.06 Figure 4. Offset Bar Installation Attach Backhoe t
ページ8に含まれる内容の要旨
Attach Backhoe to Tractor (Continued) 5. Place tractor 3-point lower lift arms between right and left mounting brackets on the backhoe. Secure into position using hitch pins (14), sleeves (13) if needed, and klik pin (17). 6. Connect double top link bar to the tractor top link bracket. Use top link pin supplied with your tractor and sleeve (9). If necessary, separate and adjust top link bars IN or OUT to maintain the backhoe vertical position. See “Tractor Connections” on page 11 for tractor
ページ9に含まれる内容の要旨
Remove Backhoe The only time the backhoe may be operated from a position other than the operator seat is during backhoe attachment and removal. Opera- tor must � Read Mounting Kit Manual instructions on attaching and removing backhoe and use extreme care. � Always stand between rear tire and back- hoe stabilizer arms or along side of tractor to avoid being trapped should the boom swing 6" Blocks BH1 control be accidentally activated. Figure 7. Backhoe Storage Position (Typical) 1. Remo
ページ10に含まれる内容の要旨
Attach Backhoe to Tractor 4. Raise the 3-point mount up by lowering stabilizers and boom section until even with tractor 3-point lift arms. Attach tractor 3-point lift arms to right and left rear brackets using hitch pins (14), This mounting kit is designed to provide sleeves (13), and klik pin (17). See page 8. secure mounting and adequate operator clear- 5. Raise backhoe with stabilizer and boom section ance when properly installed. Check clearance to establish ground clearance betwe
ページ11に含まれる内容の要旨
Tractor Connections There may be more than one hole provided in tractor top link attachment bracket. Select hole A, B, or C that most evenly distributes the load between top link bracket top and bottom mounting bolts. See Figure 8. For the Massey Ferguson 1455V tractor use hole position D. NOTE: The maximum width between tractor top link attachment plates must not exceed 2-1/2 inches. This will prevent excessive bending loads to the tractor top link pin. For tractors with draft control, select
ページ12に含まれる内容の要旨
1012606 3-POINT MOUNTING KIT 8 12 2 16 9 16 7 1 10 12 15 3 11 8 4 12 CD7022 16 16 10 6 17 14 5 13 REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1017875 1 Top link 11 34163 * 1 7/8 NC x 5 HHCS GR5 2 37670 1 Double top link (upper) 12 34194 * 5 7/8 NC Lock nut 3 37679 2 Offset links, .75 x 3 x 32.23 x 12.95 13 34291 2 Sleeve, 5/32 x 1-7/16 x 1-7/8 4 37682 1 Right mounting bracket 14 37487 2 Hitch pin, .88 x 3.0 5 37683 1 Left mounting bracket 15 38696 2 Sleeve, .88 x 1.25 x 1.06 6 13759 * 4
ページ13に含まれる内容の要旨
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware define
ページ14に含まれる内容の要旨
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 1/2 5/8 3/4 7/8 IN 1 2 7 34 5 6 MM 25 50 75 100 125 150 175 Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG ............................................................ Agriculture NC.................................................... National Coarse ATF .............................. Automatic Transmission Fluid NF ..
ページ15に含まれる内容の要旨
WARRANTY TM TM (All Models Except Mow’n Machine Zero-Turn Mowers and Woods Boundary Utility Vehicles) Please Enter Information Below and Save for Future Reference. Date Purchased: __________________________ From (Dealer): ________________________________________ Model Number: __________________________ Serial Number:________________________________________ Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set forth bel
ページ16に含まれる内容の要旨
WARRANTY TM (Replacement Parts For All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months. Under no circumstances will this Warranty apply in th
